ABB Slimline XRG1 User manual

—
I N S TA LL AT ION I N S T R U C T I O N
Switch Disconnector Fuse
Slimline XRG1
— Switch Disconnector Fuse Slimline XRG1 rev. A / 1SEQ100099P0001

—
Table of contents
01 Use of symbols
07
ITS
10
EFM
12
Motor operation
14 Fuse replacement
15 Accessory
04 Busbar overview
Manual operation
06

1
SWI TCH DIS CON NEC TO R FUS E, XR G1
Hazardous voltage
Warns about a situation where a hazardous
voltage may cause physical injury to a per-
son or damage to equipment.
General warning
Warns about a situation where something
other than electrical equipment may cause
physical injury to a person or damage to
equipment.
—
Use of symbols
Caution
Provides important information or warns
about a situation that may have a detrimen-
tal effect on equipment.
Information
Provides important information about the
equipment.

—
Receiving, handling and storage
Receiving and handling
Upon receipt, carefully inspect the switch
for damage that may have occurred during
transit. If damage is evident, or there is vis-
ible indication of rough handling, immedi-
ately file a damage claim with the transpor-
tation company, and notify your local ABB
sales office.
Do not remove the shipping package until
ready to install the switch.
Storage
If the unit will not be placed into service im-
mediately, store the switch on its original
package in a clean, dry location. To prevent
condensation, maintain a uniform tempera-
ture. Store the unit in a heated building, al-
lowing adequate air circulation and protec-
tion from dirt and moisture. Storing the
unit outdoors could cause harmful conden-
sation inside the switch enclosure.
HAZARD OF EQUIPMENT
OVERTURNING
When moving with a fork lift, do not re-
move the shipping package until the device
is in its final location.
Failure to follow this instruction will result
in personal injury or equipment damage.
Warning
2SWI TC H D ISCO NN ECTOR FU SE, XRG 1

—
Read these safety instructions
carefully before using this product!
HAZARD OF ELECTRIC SHOCK,
EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective
equipment and follow safe electrical work
practices.
• This equipment must only be installed
and serviced by qualified electrical per-
sonnel.
• Before performing visual inspections,
tests, or maintenance on the equipment,
disconnect all sources of electric power.
Assume that all circuits are live unless
they are completely deenergized, tested,
grounded, and tagged. Pay particular at-
tention to the design of the power sys-
tem. Consider all sources of power, in-
cluding the possibility of backfeeding.
• Turn off switch before removing or mak-
ing load side connections.
• Always use a properly rated voltage sens-
ing device at all line and load to confirm
switch is off.
• Turn off power supplying switch before
doing any other work on or inside switch.
Failure to follow these instructions could
result in death or serious injury.
Danger
3
SWI TCH DIS CON NEC TO R FUS E, XR G1

—
Busbar overview
A B C
D
F
E
A
B
C
D
E
F
50/5-2p
-
-
-
100
75
5
50/5-3p
50
50
-
-
75
5
50/5-4p
50
50
50
-
75
5
50/10-2p
-
-
-
100
75
10
50/10-3p
50
50
-
-
75
10
50/10-4p
50
50
50
-
75
10
4SWI TC H D ISCO NN ECTOR FU SE, XRG 1

—
Busbar overview
A
B
C
D
E
F
185/10-2p
-
-
-
370
77.5
10
185/10-3p
185
185
-
-
77.5
10
185/10-4p
185
185
97.5
-
77.5
10
AB
C
D
F
E
5
SWI TCH DIS CON NEC TO R FUS E, XR G1

—
Manual operation
1
2
45°
3
(4)
44
(4)
6SWI TC H D ISCO NN ECTOR FU SE, XRG 1

—
Motor operation
1
45°
24
3
5(5)
5
7
SWI TCH DIS CON NEC TO R FUS E, XR G1

—
Motor operation
Front cover must be
locked before operating
Close
Open
2
1
8SWI TC H D ISCO NN ECTOR FU SE, XRG 1
Signal: >0.5 sec or permanent