ABB ACS880-01 Series User manual

maher.co.ir
ac.maher.co.ir

ABB industrial drives
User’s manual
ACS880-01 democase
Power and productivity
for a better world™


 
maher.co.ir
ac.maher.co.ir

2 User’s manual – ACS880  01 democase
List of related manuals
Drive hardware manuals and guides Code (English)
ACS880-01 hardware manual 3AUA0000078093
ACS880-01 quick installation guide for frames R1 to R3 3AUA0000085966
ACS880-01 quick installation guide for frames R4 and R5 3AUA0000099663
ACS880-01 quick installation guide for frames R6 to R9 3AUA0000099689
Drive firmware manuals and guides Code (English)
ACS880 primary control program firmware manual 3AUA0000085967
ACS880 drives with primary control program, quick startup 3AUA0000098062
guide
Option manuals and guides Code (English)
ACS-AP-I and ACS-AP-S assistant control panel user’s 3AUA0000085685
manual
Drive composer Start-up and maintenance PC tool User’s 3AUA0000094606
manual
Manuals and quick guides for I/O extension modules,
fieldbus adapters, encoder interfaces, etc.
You can find manuals and other product documents in PDF format on the Internet.
Go to www.abb.com/drives and select Document Library. You can browse the library
or enter selection criteria, for example a document code, in the search field.
ABB industrial drives

maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 3
SI1 SI2 SI3 SI4
IO-panel
STO 1 & 2
IO-cable
SI1-
button
(The red button on the lower left corner of the demo)
Safety instructions
General safety instructions
These safety instructions are intended for all personnel who work on the drive. For
complete safety instructions, see the drive manuals.
Ignoring these instructions can cause physical injury or death, or damage the
equipment. All electrical installations and maintenance work on the drive should be
carried out by qualified electricians only.
WARNING!
•Make sure that the drive and all adjoining equipment are properly
earthed.
•Do not attempt any maintenance on powered drive.
•After switching off the mains, always allow the intermediate circuit
capacitors 5 minutes to discharge before doing any maintenance
work on frequency converter, the motor or the motor cable.
•It is good practice to check (with a voltage indicating instrument) that
the drive is in fact discharged before beginning work.
WARNING!
If the demo unit is operated within the transportation enclosure, please
note that the motors and drives have less air available for cooling, which
may result in overheating.
Safety input connections
The safety connections in the demo are made as in the picture below. Safety inputs
2, 3 and 4 are not in use by default. Note that if the IO-cable is not connected, it will
automatically result in activation of the STO (safe torque off).
maher.co.ir
ac.maher.co.ir

4 User’s manual – ACS880  01 democase
Delivery content
ACS880-01 democase contains: (found in the pocket at the
back of the demo)
1. IO-panel with removable control panel
2. USB to Mini USB –cable for PC-connection
3. Ethernet cable for IO-panel connection
4. Quick installation guide ACS880-01 frames R1 to R3
5. Mains cord
6. Manual CD
7. FENA-01/-11 Ethernet adapter module manual
8. FEN-31 HTL encoder interface quick guide
9. Quick start-up guide for primary control program
1
2
3
4
5
6
9
7
8
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 5
Basic start-up
1. Lay the democase on its back (so that the door is pointing up) and open the door.
2. Pull the demo out of the case using the lifting strap and the handle hole (on the
lower part of the demo.) Warning! The demo weighs approximately 25kg. Use of
proper lifting technique with a straight back is advised.
3. Take out the mains cord and Ethernet cable from the pocket at the back of the
demo.
4. Plug in the mains cord and Ethernet cable (to connections marked: mains cord,
IO-panel connection A and IO-panel connection B on the layout section.)
5. Check that the Input voltage switch (115V/230V) is set according to the supply
voltage.*
6. Check that the Drive Main Supply is switched on.
7. Switch on the demo using the mains switch.
8. You can toggle control between the control panel and the IO-panel with the
“Loc/Rem” –button on the control panel.
* For more information check “AC input (supply) connection” in the Technical data
section
Mechanical brake
The mechanical brake is intended for momentary impulse braking for load
demonstration purposes. The mechanical brake is not designed for continuous load
which might damage the transformer and the brake itself.
maher.co.ir
ac.maher.co.ir

6 User’s manual – ACS880  01 democase
Layout
Lifting strap
IO-panel
Control panel
Mechanical
brake
Input voltage
switch
(115V/230V)
Mains swi
tch
Fuse terminal
Mains cord
connection
IO-panel
connection B
LAN
connection
D2D
connection
24V out
External
power
External ZCU
supply switch
Safety input 1
(default: STO)
Drive main
supply switch
USB connection
IO-panel
connection A
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 7
Default IO button functions
SI1: Safe torque off (1)
SI2, SI3 & SI4
:
Not in u
se
(0= LED off,
1= LED on
)
AI1: Speed reference
AO1: Motor speed
AI2: Not in use
AO2: Motor current
DI1: Stop (0), Start (1)
DI2: Forward (0),
Reverse (1)
DI3: Reset
DI4:Ramp selection
DI5: Constant speed 1
Off (0), On (1)
DI6: Not in use
DIIL: Not in use
RO1: Ready (1)
RO2: Running (1)
RO3: Faulted (-1)
DIO1: Output:
Ready (1)
mode: Input (0),
Output (1)
DIO2: Output:
Running (1)
mode: Input (0),
Output (1)
maher.co.ir
ac.maher.co.ir

8 User’s manual – ACS880  01 democase
Parameters that need to be changed
Parameter
Name Setting Notes
95 HW configuration
95.01 Supply voltage [2] 380…415 V Correct rating settings made
91 Encoder module settings
91.11 Module 1 type [4] FEN-31
91.12 Module 1 location 003 FEN-31 location in Option slot 3
92 Encoder 1 configuration
92.01 Encoder 1 type [5] HTL
92.02 Encoder 1 source [1] Module 1
92.10 Pulses/revolution 1024
92.12 Speed calculation mode [0] A&B all
92.13 Position estimation enable [0] Disable
92.15 Transient filter [2] 1220 Hz
92.20 Enc cable fault func [0] No
After setting feedback parameters, activate settings with
91 Encoder 1 configuration
91.10 Encoder parameter refresh [1] Configure Will return to 'Done'after refresh
90 Feedback selection
90 .41 Motor feedback selection [1] Encoder 1
I/O settings
12 Standard AI
12.25 AI2 unit selection [2] V
12.28 AI2 max 10
Motor parameters and ID-run
99 Motor data
99.03 Motor type [0] Asynchronous
motor
99.04 Motor ctrl mode [0] DTC
99.06 Motor nominal current 1.2 A
99.07 Motor nominal voltage 230 V
99.08 Motor nominal frequency 50 Hz
99.09 Motor nominal speed 1360 rpm
99.10 Motor nominal power 0.18 kW
99.11 Motor nominal cosfii 0.71
99.13 Identification run request [1] Normal Start ID-run in 'Remote': Press DI1 ,
in 'Local': Press panel Start button
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 9
Supply switches
The democase supply can be controlled with the switches External ZCU supply
switch and Drive main supply switch. The two switches work separately. The
External ZCU supply switch controls the external 24V supply to the control unit of the
drive and the Drive main supply switch controls the 400V main supply to the drive.
For information about the internal connections refer to section: Technical data.
Change of fuse
WARNING! Turn off the democase and disconnect the power cord before
changing the fuse. Replace the fuse with the same type of fuse.
Changing the fuse does not require any tools. Open the fuse terminal by pressing
together the pins on the top and bottom of the fuse terminal and pulling the terminal
out. Pull out the old fuses and replace them with new fuses of the same type. Push
the fuse terminal back in.
Correct fuse type is: T2AL250V (Slow, 2.0A, 250V glass tube fuse)
There are two fuses of this type in the fuse terminal.
maher.co.ir
ac.maher.co.ir

10 User’s manual – ACS880  01 democase
Technical data
Dimensions
Height: 650 mm
980 mm (trolley handle pulled up)
Width: 490 mm
Depth: 385 mm
Weight: 30 kg
Drive type code
ACS880-01-02A4-3+K473+L502
(K473 = FENA-11, L502 = FEN-31)
Motor details
ABB M2VA 63 B 4 (3GVA 062 142-ASC)
AC input (supply) connection
U1 ~ 100V - 240V
The democase can be used with both 115V and 230V supply. It is important to check
that the input voltage switch (115V/230V) is in the correct position for the supply. I.e.
if you are using 230V supply, then “230V” should be visible in the switch. If the
switch is set incorrectly you will burn the fuse.
Degree of protection
Drive: IP21
Motor: IP55
Parameter
ACS880
-
01 parameter
Value
Motor type 99.03 Motor type AM
Rated current In 99.06 Motor nominal current 1.2 A
Rated voltage Un 99.07 Motor nominal voltage 230.0 V
Frequency Fn 99.08 Motor nominal frequency 50.0 Hz
Rated speed 99.09 Motor nominal speed 1360 rpm
Rated power Pn 99.10 Motor nominal power 0.18 kW
COS 99.11 Motor nominal cosfii 0.71
Rated torque 99.12 Motor nominal torque 0.82 Nm
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 11
Ambient conditions
The demo is designed for demonstration purposes and for indoor use only.
Ambient temperature:
- Transport: -40 to +70 °C
- Storage: -40 to +70 °C
- Operation: -15 to +40 °C, no frost allowed
Altitude:
- 0 to 4,000 m without an effect on demo operation
Relative humidity:
- 5 to 95%, no condensation allowed
For more detailed information, refer to the drive Hardware Manual.
Internal connections
230V
115V
400V
24V
Drive Main
Supply switch
Ext ZCU
Supply switch
Mains switch
ACS880-01
drive
M2VA 63 B 4
motor
Input voltage switch
(115V/230V)
maher.co.ir
ac.maher.co.ir

12 User’s manual – ACS880  01 democase
Further information
Product and service inquiries
Address any inquiries about the product to your local ABB representative, quoting
the type designation and serial number of the unit in question. A listing of ABB sales,
support and service contacts can be found by navigating to www.abb.com/drives and
selecting Sales, Support and Service network.
Product training
For information on ABB product training, navigate to www.abb.com/drives and select
Training courses.
Providing feedback on ABB Drives manuals
Your comments on our manuals are welcome. Go to www.abb.com/drives and select
Document Library – Manuals feedback form (LV AC Drives).
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 13
This page is intentionally left blank.
maher.co.ir
ac.maher.co.ir

14 User’s manual – ACS880  01 democase
This page is intentionally left blank.
maher.co.ir
ac.maher.co.ir

User’s manual – ACS880  01 democase 15
This page is intentionally left blank.
maher.co.ir
ac.maher.co.ir

16 User’s manual – ACS880  01 democase
Contact us
ABB Oy
ABB Inc.
ABB Beijing Drive Systems Co. Ltd.
Drives Drives & Motors No. 1, Block D, A-10 Jiuxianqiao Beilu
P.O. Box 184 16250 West Glendale Drive Chaoyang District
FI-00381 HELSINKI New Berlin, WI 53151 Beijing, P.R. China, 100015
FINLAND USA Telephone [phone]
Telephone [phone] Telephone [phone] Fax [phone]
Fax [phone]-800-HELP-365 www.abb.com/drives
www.abb.com/drives Fax [phone]
Automation Technologies www.abb.com/drives
3AUA0000127806 Rev A (EN) EFFECTIVE: 2012-11-02
Power and productivity
for a better world™


 
maher.co.ir
ac.maher.co.ir