ABB TL Series User manual

1/4
—
T WILI GHT SW ITCH
TL LINE
Installation manual
TL1, TL1 Pole, TLS
Installation Manual
Document ID: 9AKK107991A3020
Revision: A
2020-10-13
Disclaimer
The information in this document is subject to change without notice and should not be construed
as a commitment by ABB Spa. ABB Spa assumes no responsibility for any errors that may appear in
this document.
In no event shall ABB Spa be liable for direct, indirect, special, incidental or consequential damages
of any nature or kind arising from the use of this document, nor shall ABB Spa be liable for
incidental or consequential damages arising from use of any software or hardware described in
this document.
Copyrights
This document and parts thereof must not be reproduced or copied without written permission
from ABB Spa, and the contents thereof must not be imparted to a third party nor used for any
unauthorized purpose.
The software or hardware described in this document is furnished under a license and may be
used, copied, or disclosed only in accordance with the terms of such license.
© Copyright 2020 ABB Spa. All rights reserved.
Trademarks
ABB Spa is a registered trademark of the ABB Group. All other brand or product names mentioned
in this document may be trademarks or registered trademarks of their respective holders.
Contact
ABB SpA
Via Dell'industria, 18
20010 – Vittuone – Milano
Italy
Tel. [phone]

2/4
Safety warning
The device must always be protected on the incoming side by fuse or circuit
breaker with a max nominal current of 16A
1. Mounting Instruction TL1 + TLs (peripherical device)
Tightening torque
Important notice
After installation the cable coming out from the device must be fixed re-
liably.
2. Mounting Instruction TL1 Pole
Tightening torque

3/4
3. Technical data
TL1
TL1 Pole
Rated supply voltage
V
110 ÷ 230 AC
Contact type
1NO polarized
Incandescent lamps
110 V
W
1000
230V
W
1000
LED/CFL –externally ballasted
110 V
W
300
230V
W
300
LEDi/CFLi –self ballasted
110 V
W
30
230V
W
100
Rated frequency
Hx
50/60
Switching delay ON
s
23+-10%
25+-10%
Switching delay OFF
s
23+-10%
35+-10%
Brightness range (with tolerance of +-20%)
lx
2…200
Protection degree twilight switch
IP20
IP54
Protection degree sensor
IP54
Operating temperature twilight switch
°C
-25…+55°
-40…+70
Operating temperature sensor
°C
-40…+70
Storage temperature twilight switch
°C
-40…+70
-50…+80
Storage temperature sensor
°C
-50…+80
Power consumption
W
0.4 W cosphi 0.4 (idle)
0.9 W cosphi 0.42 (active)
0.25 W cosphi 0.35 (idle)
0.8 W cosphi 0.4 (active)

4/4
TL1
TL1 Pole
Max terminal cross section
mm2
6
Terminals
loss-proof screw
Screw Type
PZ1
Tightening torque: terminals
Nm
1.2
Tightening torque: screw sensor
Nm
1.2
Mounting
on DIN Rail
Pole/wall mounted
Switching status indication /brightness range
red/green LEDs
Max wiring length
m
100
Max wiring width
1000w
mm2
2,5
all other
mm2
1,5
sensor
mm2
0,75
Modules
n°
1
Reference standards
EN 60669-1
EN 60662-2-1
EN60730-1