Abode Hex Professional AT2094 User manual

Important Technical Data
Minimum operating pressure 1.5 bar
Maximum operating pressure 5.5 bar*
Maximum hot water temperature 70°C*
Recommended hot water temperature 46°C
ote: If these temperatures or pressures are
exceeded, even for short periods, damage
can result. In these instances a thermostatic
mixing or pressure reducing valve should be
installed.
All Abode taps are either WRAS approved
or manufactured in accordance with
recognised European standards. Please
ensure that your Abode Kitchen mixer is
fitted in accordance with Local Water
Byelaws.
These installation guidelines have been prepared for your
direction and you must exercise due care at all times. We do
not accept responsibility for problems that may occur
through improper installation. Whilst assembling the tap take
care not to accidentally loosen any screwed assemblies.
Abode is a registered trademark of Abode.
Manufacturers Product Reference
©Abode
01/2019
Unit L, Zenith Park, Whaley Road, Barnsley,S75 1HT.
Tel: [phone] Fax: [phone] www.abodedesigns.co.uk
All errors and omissions excepted.
Hex Professional
5 Year warranty
Terms and Conditions
In the unlikely event that you should experience any
defect in the materials or workmanship of your new
Abode mixer within 5 years of purchase, the
purchaser’s sole remedy shall be the replacement
(at the manufacturer’s discretion) of all or any part of
the product that is defective. All working parts and
valves are guaranteed for a period of 5 years from
purchase. Decorative surface finishes and O-rings
are guaranteed for 1 year from the date of purchase
provided that our advice concerning care has been
observed and no scouring agents have been used.
This is provided that the mixer or tap has been used
for normal domestic purposes and that the care,
installation and maintenance instructions have been
observed. The warranty extends to the original
purchaser only.
Marks, scuffs and scratches caused by improper
installation or accidental damage are not covered by
this guarantee. either are shade variations or any
damage or defect caused by incorrect installation or
abuse of the fitting.
As we are continuously improving and developing
our range of products, finishes & colours, in the
event of a valid claim, we may not be able to provide
an identical replacement for the defective product
throughout the guarantee period. Where an identical
product is no longer available, we will supply the
nearest equivalent from our then current product
range. In assessing your claim, we must be given
the opportunity to inspect the product as installed
prior to removal. Any product returns must be
packaged as received and complete.
o other warranties, express or implied, are made,
including merchantability or fitness for a particular
purpose. Under no circumstances shall the
manufacturer be liable for any loss or damage
arising from the purchase, use or inability to use this
product, or for any special, indirect, incidental or
consequential damages. o liability is accepted for
consequential damage to other household fixtures,
fittings or furnishings arising from this claim, even if
attached to the product. o installer, dealer, agent or
employee of Abode has the authority to modify the
obligations or limitations of this warranty.
Care Instructions for your Kitchen Sink tap
To maintain the appearance of this product ensure that it is regularly cleaned only using a clean soft damp
cloth. A solution of warm water and a mild liquid detergent may be used where necessary and then the
fitting rinsed thoroughly and wiped dry. Any other cleaning action will invalidate your warranty.
If the mixertap has a diffuser it should be unscrewed and cleaned periodically in warm water.
Abrasive cleaners, scouring cleaners and acidic cleaners must not be used under any circumstances. Avoid contact
with all solvents (including chlorinated solvents, ketones or acetones as these may result in surface deterioration or
etching). Also avoid contact with any harsh household chemicals such as oven cleaners, drain cleaners, rust
removers, paint strippers and toilet bowl cleaners, bar keepers friend or Brasso.
Please leave these instructions for your customer.

Parts and Contents
Key Description Qty
A Professional body 1
B Base plinth 1
C Upper seal 1
D Fixing stud 1
E Triangular stabilising bracket 1
F Lower gasket 1
G Fixing bracket 1
H Fixing nut 1
I Hot Flexi tail
(with integral RV) 1
J Cold Flexi tail
(with integral RV) 1
Installation Instructions:
Preparation
Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove
any remaining solder, swarf or impurities from your system. Failure to carry out this simple procedure could cause
problems or damage to the workings of the mixertap.
We strongly recommend installing particle filters and isolation valves to both the hot and cold feed pipes in an
accessible position. This will help to prevent premature failure of the valves and ease any future maintenance.
All parts should be removed from their packaging and inspected for any transport damage prior to installation.
Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold
taps in the house and allow the water to run until the cold-water storage tank and pipes are fully empty. Please note,
the hot water storage cylinder (if applicable) will always remain full.
This mixertap requires a 35mm∅ tap hole, if replacing an existing tap, remove the tap & clean the end of the feed
pipes using wire wool the tap hole area should be free from dirt and sealant.
Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case
do this now.
Installation
1. Screw studded rod (D) into the base of the tap (A).
2. Place the upper seal (C) into the base plinth (B) then place the base plinth (B) onto the bottom of the tap
(A).
3. Screw the hot & cold water tail pipes (I & J) into the base of the tap (A) as shown.
4. Place the mixertap (A) and base plinth (B) onto the sink/worktop, passing the tail pipes (I & J) and
studded rod (D) through the tap hole and base plinth (B)
5. Pass the triangular stabiliser (E), lower gasket (F) and then the fixing bracket (G) over the studded rod
(D) and around the flexible tail pipes (I & J)
6. Fasten the fixing nut (H) securely onto the fixing stud (D) to fix the tap (A) into its correct location.
7. Connect the hot and cold tail pipes (I & J) to the water mains using ½” BSPx15mm compression fittings.
ote: on-return valves will be pre-inserted into tail pipes (I & J).
After installation
Once you have visually checked the new fittings and connections, ensure that all taps are closed except the new
mixer tap which should be left open. Turn on the water supply at the mains stop cock. As the system starts to refill,
check carefully for leaks. Once you are fully satisfied that there are no leaks, turn on the water heating.
Clean the tap to remove any marks created during installation as instructed then place the cloth bag that has been
provided to protect the tap until it is ready for use.