Abode AB2450 User manual

Wall or Ceiling Mounted Outlet
5 Year Warranty Terms & Conditions:
In the unlikely event that you should experience any defect in the materials or workmanship of your
new Abode product within FIVE years of purchase, the purchaser’s sole remedy shall be the
replacement (at the manufacturer’s discretion) of all or any part of the product that is defective.
Valves are guaranteed for a period of FIVE years from purchase. Decorative surface finishes and O-
rings are guaranteed for ONE year from the date of purchase provided that our advice concerning
care has been observed and no scouring agents have been used.
This is provided that the product has been used for normal domestic purposes in the UK and that the
care, installation and maintenance instructions have been observed. The warranty extends to the
original purchaser only. You should retain a copy of your dated invoice as proof of purchase to
validate any claims under this warranty.
Marks and scratches caused by improper installation or accidental damage are not covered by this
guarantee. Neither are shade variations or any damage or defect caused by incorrect installation or
abuse of the fitting.
As we are continuously improving and developing our products range, finishes & colours, in the event
of a valid claim, we may not be able to provide an identical replacement for the defective product
throughout the warranty period. Where an identical product is no longer available, we will supply the
nearest equivalent from our then current product range. In assessing your claim, we must be given
the opportunity to inspect the product as installed prior to removal. Any product returns must be
packaged carefully as received and complete.
No other warranties, express or implied, are made, including merchantability or fitness for a particular
purpose. Under no circumstances shall the manufacturer be liable for any loss or damage arising
from the purchase, use or inability to use this product, or for any special, indirect, incidental or
consequential damages. No liability is accepted for consequential damage to other household
fixtures, fittings or furnishings arising from this claim, even if attached to the product. No installer,
dealer, agent or employee of Abode has the authority to modify the obligations or limitations of this
warranty.
Product Care Instructions:
To maintain the appearance of this product, ensure that it is regularly cleaned only using a clean, soft
damp cloth. A solution of warm water and a mild liquid detergent may be used where necessary, and
then the fitting rinsed thoroughly and wiped dry. Any other cleaning action or cleaning products will
invalidate your warranty.
Abrasive cleaners, scouring cleaners, limescale cleaners and acidic cleaners must not be used
under any circumstances. Avoid contact with all solvents (including chlorinated solvents, ketones or
acetones as these may result in surface deterioration or etching). Also avoid contact with any harsh
household chemicals such as bleach cleaners, drain cleaners, rust removers, paint strippers and
toilet bowl cleaners, toothpaste, mouthwash, bar keepers friend or Brasso.
Please leave these instructions for your customer.

Installation Preparation:
All parts should be removed from their packaging and inspected for any transport damage and
completeness prior to installation; you should read these instructions throughout before commencing
installation.
We do not accept responsibility for problems that may occur through improper installation. Always ensure
you have sufficient hot and cold water pressure available to allow correct function before specifying or
installing this product.
We strongly recommend installing particle filters and isolation valves to both the hot and cold feed pipes
in an accessible position. This will help to prevent premature failure of the valves and ease any future
maintenance.
Shut off your water heating system and ensure that your mains stopcock is closed. Ensure both the hot
and cold water supplies are isolated before commencing installation.
Installation:
Key Description Qty.
A
Shower arm /
Wall outlet
1
B
Back plate
(*Dependant
on model)
1*
C
½” Female 90°
backplate
elbow
0
D
½” Union
(*Dependant
on model)
1*
E
Finished wall /
ceiling surface
n/a
F Rigid inlet pipe 0
G Wall fixings 0
1. Open the wall / ceiling out to the required width and depth for supply pipes (F) and elbow (C).
•All serviceable parts should be given suitable access to allow easy future maintenance.
•You should ensure that both the product and required fittings will fit into the depth and area
of the mounting surface available before installation. Roughly assemble the product and
plumbing connections (example ½” union (D) to establish the required sizes ‘A-C’.
‘A’
Distance from finished
surface to fixed
connector
‘B’
Cavity depth for
supply pipes and
fixings
‘C’ Finished hole
diameter

2. Fix elbow (C) or inlet pipes (F) securely to the wall or ceiling using appropriate fixings (G). Note
these fixings should be secure enough to support the attached products weight safely during use.
•Before installing this new connection it is essential that you thoroughly flush through
the supply pipes in order to remove any remaining solder, swarf or impurities from your
system. Failure to carry out this simple procedure could cause problems or damage to the
workings of any attached product and invalidate the warranty.
3. If the shower arm / wall outlet (A) has a ½” Female connection then screw an appropriate sized ½”
Union (D) into ½” elbow (C) to suit the fitting depth and the shower arm / wall outlet (A) connection
size using PTFE tape or sealing compound to ensure a water tight connection, cap off the
incoming pipework and pressure test it for leaks, if tested ok remove the testing cap but cover it
temporarily with a cloth to prevent dirt entering the supply feed.
4. Make good the finished surface (E) using tiles or similar, now prepare hole ‘D’ in the tiles. Ensure
back plate (B) will cover the finished hole diameter ‘C’.
5. If applicable put back plate (B) over the shower arm / wall outlet (A).
6. Screw the shower arm / wall outlet (A) into the elbow (C) or ½” Union (D) using PTFE tape or
sealing compound to ensure a water tight connection and the body of the outlet (A) faces the
correct direction. Test the water tightness of all inlet pipes and connections before progressing with
the installation.
7. Watchfully Seal around the finished wall surface (E) and back plate (B) if applicable to prevent
water ingress into the wall. Note take care not to apply sealant to sections of thread on the shower
arm / wall outlet (A) or ½” Union (D) that are required for fixing later.
After installation:
Once you have visually checked the installation of the new product and all connections, ensure that all other
fittings are closed except the new product which should be left open.
Turn on your water heating system and ensure that your mains stopcock is open. Reconnect both the hot and
cold water supplies to this fitting.
Check the function of flow and function of hot, cold and mixed water, where possible check the function of the
thermostatic valve maximum temperature, and shut off function by interrupting the cold water source during
use.
Turn off the product and check carefully for any leaks around all connections on the fitting and adjoining
plumbing. If possible return to the installation after a longer period to double check for slower leaks. If pressure
testing equipment is available check the installation to the maximum recommended pressure.
Clean the product to remove any marks created during installation as instructed, and then place a bag over the
product to protect the product finish until it is ready for use.

Important Technical Data:
•Minimum operating pressure: only applicable to models supplied with shower head, check
you have sufficient water pressure for the model you are installing at
www.abodedesigns.co.uk before installation.
•Maximum operating pressure 5 bar*
*Note: If this pressure is exceeded, even for short periods, damage can result. In these instances a
pressure reducing valve should be installed
For safety purposes do not use any products as a grab or support rail
All Abode products are either WRAS approved or manufactured in accordance with recognised
European standards. Please ensure that your Abode product is fitted in accordance with Local
Water Byelaws.
Whilst assembling this product take care not to accidentally loosen any screwed assemblies. PTFE
tape can be used to ensure watertight joins on threaded connections, do not over tighten
connections or allow pipes to be twisted or folded.
The installation should be periodically checked for damage, if the property is left unattended for a
prolonged period we recommend isolating water supplies.
All errors and omissions excepted.
Manufacturers Reference
©Abode 04/2020
Unit L, Zenith Park, Whaley Road, Barnsley,S75 1HT.
Tel: [phone] Fax: [phone]
www.abodedesigns.co.uk