aci aSENSE RL User manual

Dismounting of the sensor
Pull the top part upwards
Push the front part with the lid upwards Fold the front part with the lid forwards
while keeping the wall plate steady and loose it from the hooks (#1)
4
3
2
6
1
5
1
aSENSE RL
1 top part
2 lid
3 front part
4 wall plate
5 screw
6 label with settings
inside the top part
Installation and Operation Instructions
Installation Instructions AUTOMATION COMPONENTS, INC
I0000658Rev 1 Page 1 of 4 2305 Pleasant View Road
Middleton, Wisconsin 53562
[phone]
www.workaci.com

Installation Instructions AUTOMATION COMPONENTS, INC
I0000658Rev 1 Page 2 of 4 2305 Pleasant View Road
Middleton, Wisconsin 53562
[phone]
www.workaci.com
Mounting of the sensor
The wall plate is screwed onto the wall (A) Put the top tabs of the front part into the top
The screw head diameter should be max 7,5 mm holes of the wall plate.
The screw head height should be max 2,5 mm (B) Press the lower edge of the case onto
the wall plate to latch
+
~
The top part is pushed under the Terminals and jumpers on aSENSE RL.
locking hooks of the wall plate The darker positions are default settings.
and is secured with a screw Terminals and jumpers are located under the top part.
If for some reason the PCB must be removed it must be handed carefully
and protected from electrostatic discharge! Normally, removing the PCB is
not required.
A
B
+
~
(Unit without Relay)

Installation Instructions AUTOMATION COMPONENTS, INC
I0000658Rev 1 Page 3 of 4 2305 Pleasant View Road
Middleton, Wisconsin 53562
[phone]
www.workaci.com
Electrical connections
The power supply has to be connected to and . is considered as
system ground. If the analogue output is connected to a controller the same ground
reference has to be used for the aSENSE RL unit and for the control system! Unless
different transformers are used, special precautions need to be taken.
PLEASE NOTE! The same ground reference
has to be used for the aSENSE RL unit and for
the control system!
If possible keep the sensor powered up after mounting.
Connect the analogue output before measuring.
Connection
Terminal
Function
Electrical Data
Remarks
Power (+)
Power ground (-)
24 VAC/DC+ (+-20%),
3W
24 VAC/DC-
2W without output
load
See note 1!
Out(1)
Out(2)
Analogue Output 1 (+)
Analogue Output 2 (+)
0-10 VDC or 0-20 mA,
2-10 VDC or 4-20 mA,
Same as Output 1
According to positions
of OUT1 and start
point jumpers.
See note 2!
According to positions
of OUT2 and start
point jumpers.
See note 2 and 3!
5
6
7
Normally closed relay
Relay COM
Normally open relay
Contact free relay
minimum load 1mA/5V
rated load
0,5A/125VAC;
1A/24VDC
Triggered by register
Out(3)
8
Not used
Table I. Electrical terminal connections for aSENSE RL
Note 1: The ground terminal is used as negative power supply DC input or AC phase ground
(halfwave rectifier). A single transformer may be used for the entire system.
Note 2:aSENSE RL can deliver a voltage or a current loop for Out(1) / Out(2). To change between
voltage and current output mode the hardware jumpers are used. There is one jumper for Out(1) and
one for Out(2), so that one output can be a voltage output and the other a current output. Both, voltage
output and current output can have start points 0 % (0-10 VDC or 0-20mA) or 20% (2-10 VDC or 4-
20mA). The same start point is used for both outputs. See the function manual.
Note 3: Please use voltage outputs for temperature measurements. The accuracy of temperature
measurements is valid only for units configured in voltage outputs mode.
~
+
~
+

Installation Instructions AUTOMATION COMPONENTS, INC
I0000658Rev 1 Page 4 of 4 2305 Pleasant View Road
Middleton, Wisconsin 53562
[phone]
www.workaci.com
Dimensions and holes
Dimensions of sensor in mm and (inches)
Dimensions of mounting plate in mm and (inches)
120(4,72)
31(1,22)
83(3,26)
29,8(1,17)
30(1,18)
7,8(0,31)
4,2(0,16)
2(0,08)
52,5(2,07)
30(1,18)
25(0,98)
30(1,18)
Mounting of the sensor onto the
wall
Please use screws with screw
head diameter less than 7,5 mm
(0,295 inches) and screw head
height less than 2,5 mm (0,1
inches)