ACV 381323-01 User manual

2
1
4
3
© 12/2008 ALL RIGHTS RESERVED. Technical changes possible. No liability for misprints.
Compatible with double DIN devices
 •PorscheCayenne
Double DIN Kit contents
• (1) Metal Frame
• (2) Facia Plate
Installation Kit (3)
Trim Frame (4)
InstallationManual
DoubleDINKit
Part-No.: 381323-01

LOCATION & REMOVAL
With the head unit now removed locate the power ISO
plug and the Black optical plug shown below.
Insert OPTICAL leads into TOOKI-POR loom and car loom
to create loop, see diagram below
To remove the (out) fibre optic cable from the factory con-
nector you will need to remove the black outer casing and
push out the blue locking insert. You will need to do the
same to insert the cable into the supplied loom. (shown in
previous fig)
Next connect the Yellow to 12v+ perm and the Black to
12v– ground (you may use the 12v+ & 12v- from the power
iso) , plug in the microphone (supplied) and insert optical
plug into the interface.
INSTALLATION
Installation is made at the front unit.
To remove the head unit you will need to remove the
surrounding trim then the 4 screws securing the unit, as
below. Some models are removed with specific radio
keys.
TOOKI-POR is designed to work with a radio that has a
factory SIM card based GSM phone option rather than
Bluetooth. As such, certain functions displayed on the
radio are not supported by the TOOKI-POR.
The factory phone module (if fitted) will need to be re-
moved from its power and optical connection (optical
cables must be re-connected to continue loop) This
module is located under the drivers (O/S) seat on all
models. It is possible to install the TOOKI kit at the Fac-
tory phone location and allocate 12v+ perm and
ground.
INTERFACE CAR CONNECTOR
OUT cable from screen
IN cable from interface
1. Press TEL on PCM Radio.
2. “Tooki Searching” indicates no phone connected.
3. Start the pairing procedure on your mobile phone.
Make sure the Bluetooth feature is turned on.
Consult your phone’s manual for phone-specific
pairing procedures.
4. Once your mobile phone discovers Tooki xxxx
(last 4 digits will vary), select and pair Tooki.
5. When prompted for a passkey, enter 6888 on your
mobile phone.
6. Once pairing is complete, go to the head unit and
select “dialled calls” Choose the phone you wish to
pair, choose select,. Go down to “dial” and press
bottom right rotary control. After a short while you
should see your signal strength indicator on the
PCM Radio. Pressing “Tel” will then show you
your network provider and signal strength.
7. You may pair up to 5 different mobile phones.
For information on phone selection, section 6
8. To delete a paired phone select phone book, scroll to
the phone name you wish to delete, select the name
by pushing the rotary button. When the name is se-
lected press the “phone up” hard key on the unit and
you should see the message “deleting”
OPERATING INSTRUCTIONS
Mount the metal brackets to the
double DIN head unit.
The position of the copper
coloured holder can be adjusted
to your needs for perfect t.
(see sample)
(sample photo) (sample photo)
InstallationManualDoubleDINKit381323-01
1. Porsche Cayenne with
OEM head unit.
3. Place facia plate on the dash-
board. Fix it with the 4 original
screws.
Push the Metal Frame into the
facia plate
Connect all required circuit points
and push the double DIN head
unit in the metal frame until it
snaps in.
Place the trim frame.
Reinstall everything in reverse
order to nish installation.
All installation work must be performed by a qualied professional installer only.
The manufacturer / dealer is not liable for any kind of incidential or indirect damages.
2. Remove trim frame, surrounding
the OEM head unit.
Remove the 4 screws.
Remove the OEM head unit.