Adaptec 2100S - SCSI RAID Controller Safety guide

STORAGE MANAGEMENT
SOFTWARE USER’SGUIDE
A DAPTEC ATA RAID 2400A
A DAPTEC SCSI RAID 2100S/3200S/3210S/3400S/3410S

R
Adaptec
Storage Management Software
User’s Guide

Copyright
© 2001 Adaptec, Inc. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the prior
written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec and the Adaptec logo are trademarks of Adaptec, Inc., which may be
registered in some jurisdictions. Windows 95, Windows 98, Windows Me,
Windows NT, and Windows 2000 are trademarks of Microsoft Corporation in the US
and other countries, used under license.
All other trademarks are the property of their respective owners.
Changes
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from
errors or omissions in this document, or from the use of the information contained
herein.
Adaptec reserves the right to make changes in the product design without reservation
and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER
REMEDIES.

Adaptec Software License Agreement
PLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE
SOFTWARE LICENSE TERMS OF ADAPTEC, INC. AND OTHER LICENSORS
WHOSE SOFTWARE MAY BE BUNDLED WITH THIS PRODUCT.
BY YOUR USE OF THE SOFTWARE INCLUDED WITH THIS PRODUCT YOU
AGREE TO THE LICENSE TERMS REQUIRED BY THE LICENSOR OF THAT
SOFTWARE, AS SET FORTH DURING THE INSTALLATION PROCESS. IF YOU DO
NOT AGREE TO THE LICENSE TERMS APPLICABLE TO THE SOFTWARE, YOU
MAY RETURN THE ENTIRE UNUSED PRODUCT FOR A FULL REFUND.
(Single User, Non-Networked Applications)
In return for acquiring a license to use the Adaptec software, which may include
software from third party licensors and patches made available by Adaptec
(“Software”), and the related documentation, you agree to the following terms and
conditions:
1. License. This Agreement grants you, the Licensee, a license to:
a. Use the Software on a single computer system, which is not intended for use
by more than five (5) users; and:
b. Make one copy of the Software in machine readable form solely for back-up
purposes, provided you reproduce Adaptec's copyright proprietary legends.
Notwithstanding the foregoing, the Software may be used on the home, laptop
or other secondary computer of the principal user of the Software, and an
additional copy of the Software may be made to support such use. As used in
this license, the Software is “in use” when it is either loaded into RAM or
installed on a hard disk or other permanent memory device. The Software may
be “in use” on only one computer at any given time. (Different license terms
and fees are applicable for networked or multiple user applications.) As a
specific condition of this license, you agree to use the Software in compliance
with all applicable laws, including copyright laws, and that you will not copy,
transmit, perform or distribute any audio or other content using the Software
without obtaining all necessary licenses or permissions from the owner of the
content.
2. Restrictions. You may not distribute copies of the Software to others or
electronically transfer the Software from one computer to another over a network.
You may not post or otherwise make available the Software, or any portion
thereof, in any form, on the Internet. You may not use the Software in a computer
service business, including in time sharing applications. The Software contains
trade secrets and, in order to protect them, you may not decompile, reverse
engineer, disassemble, or otherwise reduce the Software to a human-perceivable
form. YOU MAY NOT MODIFY, ADAPT, TRANSLATE, RENT, LEASE, LOAN,
RESELL FOR PROFIT, DISTRIBUTE, NETWORK OR CREATE DERIVATIVE
WORKS BASED UPON THE SOFTWARE OR ANY PART THEREOF.

3. Ownership of Software. As Licensee, you own the media upon which the software
is recorded or fixed, but Adaptec and its licensors retain title and ownership of the
Software recorded on the original media and all subsequent copies of the
Software, regardless of the form or media in which or on which the original and
other copies may exist. This license is not a sale of the Software or any copy.
4. Confidentiality. You agree to maintain the Software in confidence and that you
will not disclose the Software to any third party without the express written
consent of Adaptec. You further agree to take all reasonable precautions to
preclude access of unauthorized persons to the Software.
5. Term. This license is effective until January 1, 2045, unless terminated earlier. You
may terminate the license at any time by destroying the Software (including the
related documentation) together with all copies or modifications in any form.
Adaptec will have the right to terminate our license immediately if you fail to
comply with any term or condition of this Agreement. Upon any termination,
including termination by you, you must destroy the Software (including the
related documentation), together with all copies or modifications in any form.
6. Special Terms Applicable to Databases. Where a database is included with the
Software, you acknowledge that it is licensed only in connection with the use of
the Software to perform disc creation, and that the database and all data derived
therefrom must be maintained in confidence in accordance with the provisions of
Section 4. This license does not grant you any rights to distribute or disclose such
database or data.
7. Limited Warranty. Adaptec and its Licensor warrant only that the media upon
which the Software is furnished will be free from defects in material or
workmanship under normal use and service for a period of thirty (30) days from
the date of delivery to you. ADAPTEC AND ITS LICENSORS DO NOT AND
CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU MAY OBTAIN
BY USING THE SOFTWARE OR DOCUMENTATION. THE FOREGOING
STATES THE SOLE AND EXCLUSIVE REMEDIES ADAPTEC AND ITS
LICENSORS WILL PROVIDE FOR BREACH OF WARRANTY. EXCEPT FOR THE
FOREGOING LIMITED WARRANTY, ADAPTEC AND ITS LICENSORS MAKE
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED, AS TO NON-INFRINGEMENT OF THIRD PARTY RIGHTS,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states
do not allow the exclusion of implied warranties or limitations on how long an
implied warranty may last, so the above limitations may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
8. The entire liability of Adaptec and its licensors, and your exclusive remedy for a
breach of this warranty, shall be:
a. The replacement of any media not meeting the above limited warranty which
is returned to Adaptec; or:
b. if Adaptec or its distributor is unable to deliver replacement media which is
free from defects in materials or workmanship, you may terminate this
Agreement by returning the Software and your money will be refunded.

9. Limitation of Liability. IN NO EVENT WILL ADAPTEC OR ITS LICENSORS BE
LIABLE TO YOU FOR ANY INCIDENTAL, CONSEQUENTIAL OR INDIRECT
DAMAGES, INCLUDING ANY LOST PROFITS, LOST SAVINGS, OR LOSS OF
DATA, EVEN IF ADAPTEC OR A LICENSOR HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER
PARTY. Some states do not allow the exclusion or limitation of special, incidental,
or consequential damages, so the above limitation or exclusion may not apply to
you.
10. Export. You acknowledge that the laws and regulations of the United States and
other countries may restrict the export and re-export of the Software. You agree
that you will not export or re-export the Software or documentation in any form in
violation of applicable United States and foreign law.
11. Government Restricted Rights. The Software is subject to restricted rights as
follows. If the Software is acquired under the terms of a GSA contract: use,
reproduction or disclosure is subject to the restrictions set forth in the applicable
ADP Schedule contract. If the Software is acquired under the terms of a DoD or
civilian agency contract, use, duplication or disclosure by the Government is
subject to the restrictions of this Agreement in accordance with 48 C.F.R. 12.212 of
the Federal Acquisition Regulations and its successors and 49 C.F.R. 227.7202-1 of
the DoD FAR Supplement and its successors.
12. General. You acknowledge that you have read this Agreement, understand it, and
that by using the Software you agree to be bound by its terms and conditions. You
further agree that it is the complete and exclusive statement of the agreement
between Adaptec and you, and supersedes any proposal or prior agreement, oral
or written, and any other communication between Adaptec and you relating to
the subject matter of this Agreement. No additional or any different terms will be
enforceable against Adaptec unless Adaptec gives its express consent, including
an express waiver of the terms of this Agreement, in writing signed by an officer
of Adaptec. You assume full responsibility for the use of the Software and agree to
use the Software legally and responsibly. This Agreement shall be governed by
California law, except as to copyright matters, which are covered by Federal law.
This Agreement is deemed entered into at Milpitas, California by both parties.
Should any provision of this Agreement be declared unenforceable in any
jurisdiction, then such provision shall be deemed severable from this Agreement
and shall not affect the remainder hereof. All rights in the Software not specifically
granted in this Agreement are reserved by Adaptec.
Should you have any questions concerning this Agreement, you may contact Adaptec
by writing to:
Adaptec, Inc.
Legal Department
691 South Milpitas Boulevard
Milpitas, California 95035.

vii
Contents
1 Storage Management Software Overview
2 Storage Manager on ROM
Overview 2-2
Keyboard Reference 2-3
Menu Control 2-3
Left Pane – Tree View Control 2-4
Right Pane – Information View Control 2-4
Menu Reference 2-4
File 2-4
RAID 2-5
Action 2-5
Help 2-5
Icon Reference 2-6
Screen Layout 2-6
The Menu Bar 2-7
The Left Pane – Tree View 2-7
The Right Pane – Information View 2-8
Running SMOR 2-9
Information and Configuration Views 2-10
Controller BIOS Settings 2-10
Information Tab 2-13
Configuration Tab 2-15
Bus Configuration Tab 2-17
Device Information Tab 2-20
Array and Array Group Information 2-23
Setting the Configuration 2-25
Array Operations 2-26
Creating an Array 2-26
Creating a Multilevel RAID 2-28
Deleting an Array 2-29
Hot Spares 2-30
Rebuilding a Failed Array 2-31
Formatting a Drive – SCSI only 2-31
Upgrading Firmware – Flash HBA Option 2-32
Creating a SMOR Boot Disk 2-34

viii
Contents
3 Storage Manager
Introduction 3-2
System Requirements 3-3
Installing Storage Manager 3-4
Running Storage Manager 3-5
Using Storage Manager Locally 3-6
Using Storage Manager Remotely 3-6
Views 3-6
Physical Configuration View 3-6
Logical Configuration View 3-8
Logical Device Addresses 3-10
Array Groups 3-12
Status Reporting 3-23
Information Windows 3-24
Host Bus Adapter Information Window 3-24
Battery Backup Configuration Window – Adaptec 3200S/
3210S/3400S/3410S Only 3-26
Configure Host Bus Adapter Window 3-27
Flash Configuration Window 3-29
Device Information Window 3-31
Device Configuration Window 3-33
Saving the Subsystem Configuration 3-34
Events 3-35
Event Log 3-35
Event Broadcaster 3-37
Event Messaging by Pager – Windows 2000 and
Windows NT only 3-43
Formatting Drives – SCSI only 3-44
Drive Failures 3-45
Audible Alarm (SCSI Only)3-45
Rebuilding a Degraded Array 3-46
Assigning Hot Spares 3-47
Running a Verify Process 3-48
Background Task Priority 3-48
Controller I/O Statistics 3-49
Cache Statistics 3-51
Command Statistics 3-51
Device I/O Statistics 3-51
Remote Communication 3-54
Connecting Across a Network 3-55
Installation and Configuration 3-55

ix
Contents
4 RAIDUTIL Command Line Utility
Introduction 4-1
Exit Status 4-2
Device Address Syntax 4-2
Command Line Switches 4-3
Miscellaneous 4-4
Logical Drive Creation and Deletion 4-4
Array Modification 4-6
RAID Operation 4-7
Controller-Specific 4-8
Hot Spare Control 4-9
General Information and Feedback 4-10
ASNMP
Introduction A-1
Management Information Base A-2
Management Console A-2
Adaptec MIB Information A-3
SNMP A-5
What’s Included A-5
System Requirements A-6
Management Consoles A-6
Installing Adaptec SNMP Support A-6
Installing SNMP for Windows NT and
Windows 2000 A-7
Installing SNMP for Windows 95 A-7
Installing SNMP for Windows 98/Me A-7
Installing the MIB A-8
SNMP Architecture A-8
Adaptec SNMP Subagent A-9
Adaptec SNMP Trap Broadcaster Module A-9
BDMI
Introduction B-1
System Requirements B-2
Adaptec CI B-2
Installing DMI Support B-3
Adaptec DMI Modules B-3
DMI-Specific Files B-4

1-1
1
Storage Management
Software Overview
Your Adaptec RAID controller includes the following software tools
to manage your storage subsystem:
■Storage Manager Pro—The graphical user interface (GUI)
through which you interact with the storage subsystem. It
provides an intuitive graphical interface that enables you to do
such things as create and manage RAID arrays, set up security
levels for users and administrators, establish the means of
notifying users of disk failures, etc. Storage Manager Pro is
supported under the following operating systems:
■Windows 2000, Windows NT 4.0, Windows 95/98
■Novell NetWare 4.2; 5.x
■Red Hat Linux 6.x, 7.0
■FreeBSD
Storage Manager Pro is Adaptec’s primary RAID management
tool. For details, refer to the Storage Manager Pro User’s Guide.