ADB Safegate RELIANCE User manual

RELIANCE Omni Light
8-inch
User Manual
UM-5027, Rev. 1.0, 2020/12/10

A.0 Disclaimer / Standard Warranty
CE certification
The equipment listed as CE certified means that the product complies with the essential requirements concerning safety and
hygiene. The European directives that have been taken into consideration in the design are available on written request to
ADB SAFEGATE.
ETL certification
The equipment listed as ETL certified means that the product complies with the essential requirements concerning safety and
FAA Airfield regulations. The FAA directives that have been taken into consideration in the design are available on written
request to ADB SAFEGATE.
All Products Guarantee
ADB SAFEGATE will correct by repair or replacement per the applicable guarantee above, at its option, equipment or parts
which fail because of mechanical, electrical or physical defects, provided that the goods have been properly handled and
stored prior to installation, properly installed and properly operated after installation, and provided further that Buyer gives
ADB SAFEGATE written notice of such defects after delivery of the goods to Buyer. Refer to the Safety section for more
information on Material Handling Precautions and Storage precautions that must be followed.
ADB SAFEGATE reserves the right to examine goods upon which a claim is made. Said goods must be presented in the same
condition as when the defect therein was discovered. ADB SAFEGATE furthers reserves the right to require the return of such
goods to establish any claim.
ADB SAFEGATE's obligation under this guarantee is limited to making repair or replacement within a reasonable time after
receipt of such written notice and does not include any other costs such as the cost of removal of defective part, installation
of repaired product, labor or consequential damages of any kind, the exclusive remedy being to require such new parts to be
furnished.
ADB SAFEGATE's liability under no circumstances will exceed the contract price of goods claimed to be defective. Any returns
under this guarantee are to be on a transportation charges prepaid basis. For products not manufactured by, but sold by ADB
SAFEGATE, warranty is limited to that extended by the original manufacturer. This is ADB SAFEGATE's sole guarantee and
warranty with respect to the goods; there are no express warranties or warranties of fitness for any particular purpose or any
implied warranties of fitness for any particular purpose or any implied warranties other than those made expressly herein. All
such warranties being expressly disclaimed.
Standard Products Guarantee
Products of ADB SAFEGATE manufacture are guaranteed against mechanical, electrical, and physical defects (excluding lamps)
which may occur during proper and normal use for a period of two years from the date of ex-works delivery, and are
guaranteed to be merchantable and fit for the ordinary purposes for which such products are made.
Note
See your sales order contract for a complete warranty description.
FAA Certified product installed in the United States and purchased or funded with monies through the
Airport Improvement Program (AIP) installations guarantee
ADB SAFEGATE L858 Airfield Guidance Signs are warranted against mechanical and physical defects in design or manufacture
for a period of 2 years from date of installation, per FAA AC 150/5345-44 (applicable edition).
ADB SAFEGATE L858(L) Airfield Guidance Signs are warranted against electrical defects in design or manufacture of the LED or
LED specific circuitry for a period of 4 years from date of installation, per FAA EB67 (applicable edition).
ADB SAFEGATE LED light fixtures (with the exception of obstruction lighting) are warranted against electrical defects in design
or manufacture of the LED or LED specific circuitry for a period of 4 years from date of installation, per FAA EB67 (applicable
edition). .
UM-5027, Rev. 1.0, 2020/12/10 iii
Copyright © ADB SAFEGATE, All Rights Reserved

Note
See your sales order contract for a complete warranty description.
Liability
WARNING
Use of the equipment in ways other than described in the catalog leaflet and the manual may result in personal injury,
death, or property and equipment damage. Use this equipment only as described in the manual.
ADB SAFEGATE cannot be held responsible for injuries or damages resulting from non-standard, unintended uses of its
equipment. The equipment is designed and intended only for the purpose described in the manual. Uses not described in the
manual are considered unintended uses and may result in serious personal injury, death or property damage.
Unintended uses, includes the following actions:
•Making changes to equipment that have not been recommended or described in this manual or using parts that are not
genuine ADB SAFEGATE replacement parts or accessories.
•Failing to make sure that auxiliary equipment complies with approval agency requirements, local codes, and all applicable
safety standards if not in contradiction with the general rules.
•Using materials or auxiliary equipment that are inappropriate or incompatible with your ADB SAFEGATE equipment.
•Allowing unskilled personnel to perform any task on or with the equipment.
© ADB SAFEGATE BV
This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, photocopying, recording, nor otherwise, without ADB SAFEGATE BV's prior written consent.
This manual could contain technical inaccuracies or typographical errors. ADB SAFEGATE BV reserves the right to revise this
manual from time to time in the contents thereof without obligation of ADB SAFEGATE BV to notify any person of such
revision or change. Details and values given in this manual are average values and have been compiled with care. They are not
binding, however, and ADB SAFEGATE BV disclaims any liability for damages or detriments suffered as a result of reliance on
the information given herein or the use of products, processes or equipment to which this manual refers. No warranty is made
that the use of the information or of the products, processes or equipment to which this manual refers will not infringe any
third party's patents or rights. The information given does not release the buyer from making their own experiments and
tests.
RELIANCE Omni Light
iv
Copyright © ADB SAFEGATE, All Rights Reserved

TABLE OF CONTENTS
1.0 Safety ....................................................................................................................................................................................... 1
1.1 Safety Messages ........................................................................................................................................................................................................ 1
1.1.1 Introduction to Safety ................................................................................................................................................................................. 2
1.1.2 Intended Use .................................................................................................................................................................................................. 2
1.1.3 Material Handling Precautions: Storage .............................................................................................................................................. 3
1.1.4 Operation Safety ........................................................................................................................................................................................... 3
1.1.5 Maintenance Safety ..................................................................................................................................................................................... 3
1.1.6 Material Handling Precautions: Fasteners .......................................................................................................................................... 4
1.1.7 Material Handling Precautions, ESD ..................................................................................................................................................... 4
2.0 About this Manual ................................................................................................................................................................. 5
2.1 How to work with the manual .............................................................................................................................................................................. 5
2.2 Abbreviations and terms - AGL ........................................................................................................................................................................... 5
2.3 Abbreviations and Terms ........................................................................................................................................................................................ 5
3.0 General Information .............................................................................................................................................................. 7
3.1 Introduction to RELIANCE ...................................................................................................................................................................................... 7
3.2 LED Apron Maneuvering ........................................................................................................................................................................................ 8
3.3 LED Taxiway Edge ...................................................................................................................................................................................................... 9
4.0 Installation ............................................................................................................................................................................ 13
4.1 Unpacking the Unit ................................................................................................................................................................................................ 13
4.2 Tools required .......................................................................................................................................................................................................... 13
4.3 Installation and removal of the 8-inch light fixture ................................................................................................................................... 14
5.0 Operation .............................................................................................................................................................................. 17
5.1 RELIANCE Intelligent Lighting ........................................................................................................................................................................... 17
5.2 RELIANCE IQ and the 2A Concept ................................................................................................................................................................... 17
5.3 Sensor Interface Unit (SIU) .................................................................................................................................................................................. 17
5.4 Network Concentrator Unit (NCU) ................................................................................................................................................................... 17
5.5 Series Circuit Modem (SCM) .............................................................................................................................................................................. 17
5.6 Series Circuit Filter (SCF) ...................................................................................................................................................................................... 17
5.7 Control System Interface ..................................................................................................................................................................................... 17
5.8 Programming RELIANCE IQ ................................................................................................................................................................................ 18
5.8.1 Hardware equipment setup ................................................................................................................................................................... 18
5.8.2 Software Programming ........................................................................................................................................................................... 20
5.9 Connection in a Series Circuit ............................................................................................................................................................................ 24
5.9.1 Operational characteristics ..................................................................................................................................................................... 24
5.9.2 Power On or Default State ...................................................................................................................................................................... 24
5.9.3 Safe State ...................................................................................................................................................................................................... 24
5.9.4 Command Memory ................................................................................................................................................................................... 25
5.9.5 Soft ON/OFF ................................................................................................................................................................................................ 25
5.9.6 Sequenced Flashing .................................................................................................................................................................................. 25
6.0 Maintenance ......................................................................................................................................................................... 27
6.1 Safety instructions .................................................................................................................................................................................................. 27
6.2 Safety Considerations ........................................................................................................................................................................................... 27
6.3 Basic Maintenance Program ............................................................................................................................................................................... 28
6.4 Workshop Maintenance ....................................................................................................................................................................................... 28
6.4.1 Exploded View ............................................................................................................................................................................................. 30
6.4.2 Opening a 8‑inch fixture ......................................................................................................................................................................... 31
6.4.3 Closing a 8‑inch fixture ............................................................................................................................................................................ 31
6.4.4 Checking the light fixture for watertightness ................................................................................................................................. 33
6.4.5 Replacing a Light Engine in a 8‑inch Fixture ................................................................................................................................... 34
6.4.6 Replacing the Top Cover ......................................................................................................................................................................... 36
6.4.7 Replacing the Connection Board ......................................................................................................................................................... 39
6.4.8 Replacing the LED Board ......................................................................................................................................................................... 42
UM-5027, Rev. 1.0, 2020/12/10 v
Copyright © ADB SAFEGATE, All Rights Reserved

6.4.9 Replacing a prism, its gaskets and the blue spacers (prism protection plates) in a 8‑inch fixture ............................ 44
6.4.10 Replacing the Bottom Cover and Converter ................................................................................................................................. 48
6.4.11 Resetting the Fail-open converter 2.3 ............................................................................................................................................. 49
6.4.12 Resetting the Fail-open converters 48010921 and 48011111 ............................................................................................... 50
7.0 Spare Parts ............................................................................................................................................................................ 53
7.1 Ordering Code Apron Maneuvering omnidirectional Light ................................................................................................................... 53
7.2 Ordering Code Taxiway Edge omnidirectional Light ................................................................................................................................ 54
7.3 Components ............................................................................................................................................................................................................. 55
7.4 Screws Overview ..................................................................................................................................................................................................... 55
A.0 INTEROPERABILITY ............................................................................................................................................................. 57
B.0 POWER TABLE ...................................................................................................................................................................... 59
C.0 CABLE LOSS .......................................................................................................................................................................... 61
D.0 SUPPORT .............................................................................................................................................................................. 63
D.1 ADB SAFEGATE Website ...................................................................................................................................................................................... 63
D.2 Recycling .................................................................................................................................................................................................................... 63
D.2.1 Local Authority Recycling ....................................................................................................................................................................... 63
D.2.2 ADB SAFEGATE Recycling ....................................................................................................................................................................... 64
RELIANCE Omni Light
TABLE OF CONTENTS
vi
Copyright © ADB SAFEGATE, All Rights Reserved

List of Figures
Figure 1: RELIANCE Omni, 4 prisms ................................................................................................................................................................................... 7
Figure 2: In an 8‑in base ....................................................................................................................................................................................................... 13
Figure 3: In a 12‑in base with adapter ring ................................................................................................................................................................... 13
Figure 4: Omnidirectional Light, 4 prisms, 8-inch ...................................................................................................................................................... 30
Figure 5: Fixture upside down ............................................................................................................................................................................................ 31
Figure 6: Lifting up housing ................................................................................................................................................................................................ 31
Figure 7: Removing gasket .................................................................................................................................................................................................. 31
Figure 8: Converter with 1 connector .............................................................................................................................................................................. 32
Figure 9: Converter with 2 connectors ............................................................................................................................................................................ 32
Figure 10: Fixture facing down ........................................................................................................................................................................................... 33
Figure 11: Tightening screws .............................................................................................................................................................................................. 33
Figure 12: Light engine replacement ............................................................................................................................................................................... 34
Figure 13: Removing the LED board holder .................................................................................................................................................................. 35
Figure 14: Tightening screws .............................................................................................................................................................................................. 35
Figure 15: LED board ............................................................................................................................................................................................................. 36
Figure 16: Top cover with bottom cover ........................................................................................................................................................................ 37
Figure 17: Replacing the connection board .................................................................................................................................................................. 39
Figure 18: Two connector types (replaceable) ............................................................................................................................................................. 40
Figure 19: Red and black cable connections ................................................................................................................................................................ 41
Figure 20: LED sub assembly (Optical assembly) ........................................................................................................................................................ 43
Figure 21: Exploded view - prism replacement ........................................................................................................................................................... 45
Figure 22: Remove LED board holder ............................................................................................................................................................................. 46
Figure 23: Remove prism and gasket .............................................................................................................................................................................. 46
Figure 24: New prism into prism gasket ........................................................................................................................................................................ 46
Figure 25: Prism holder edge ............................................................................................................................................................................................. 47
Figure 26: Tighten screws in sequence ........................................................................................................................................................................... 47
Figure 27: Correct gasket position ................................................................................................................................................................................... 48
Figure 28: Converter with 1 connector ........................................................................................................................................................................... 49
Figure 29: Converter with 2 connectors ......................................................................................................................................................................... 49
Figure 30: 2-way electrical shunt / jumper .................................................................................................................................................................... 49
Figure 31: Converter with 1 connector ........................................................................................................................................................................... 50
Figure 32: Converter with 2 connectors ......................................................................................................................................................................... 50
Figure 33: Converter with 1 connector ........................................................................................................................................................................... 50
Figure 34: Converter with 2 connectors ......................................................................................................................................................................... 50
UM-5027, Rev. 1.0, 2020/12/10 vii
Copyright © ADB SAFEGATE, All Rights Reserved

RELIANCE Omni Light
List of Figures
viii
Copyright © ADB SAFEGATE, All Rights Reserved

List of Tables
Table 1: Legend Exploded View ......................................................................................................................................................................................... 30
Table 2: Interoperability matrix .......................................................................................................................................................................................... 57
UM-5027, Rev. 1.0, 2020/12/10 ix
Copyright © ADB SAFEGATE, All Rights Reserved

RELIANCE Omni Light
List of Tables
x
Copyright © ADB SAFEGATE, All Rights Reserved

1.0 Safety
Introduction to Safety
This section contains general safety instructions for installing and using ADB SAFEGATE equipment. Some safety instructions
may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this
manual where appropriate.
1.1 Safety Messages
HAZARD Icons used in the manual
For all HAZARD symbols in use, see the Safety section. All symbols must comply with ISO and ANSI standards.
Carefully read and observe all safety instructions in this manual, which alert you to safety hazards and conditions that may
result in personal injury, death or property and equipment damage and are accompanied by the symbol shown below.
WARNING
Failure to observe a warning may result in personal injury, death or equipment damage.
DANGER - Risk of electrical shock or ARC FLASH
Disconnect equipment from line voltage. Failure to observe this warning may result in personal injury, death, or
equipment damage. ARC Flash may cause blindness, severe burns or death.
WARNING - Wear personal protective equipment
Failure to observe may result in serious injury.
WARNING - Do not touch
Failure to observe this warning may result in personal injury, death, or equipment damage.
CAUTION
Failure to observe a caution may result in equipment damage.
Qualified Personnel
Important Information
The term qualified personnel is defined here as individuals who thoroughly understand the equipment and its safe
operation, maintenance and repair. Qualified personnel are physically capable of performing the required tasks, familiar
with all relevant safety rules and regulations and have been trained to safely install, operate, maintain and repair the
equipment. It is the responsibility of the company operating this equipment to ensure that its personnel meet these
requirements.
Always use required personal protective equipment (PPE) and follow safe electrical work practice.
UM-5027, Rev. 1.0, 2020/12/10 1
Copyright © ADB SAFEGATE, All Rights Reserved

1.1.1 Introduction to Safety
CAUTION
Unsafe Equipment Use
This equipment may contain electrostatic devices, hazardous voltages and sharp edges on components
• Read installation instructions in their entirety before starting installation.
• Become familiar with the general safety instructions in this section of the manual before installing,
operating, maintaining or repairing this equipment.
• Read and carefully follow the instructions throughout this manual for performing specific tasks and
working with specific equipment.
• Make this manual available to personnel installing, operating, maintaining or repairing this
equipment.
• Follow all applicable safety procedures required by your company, industry standards and
government or other regulatory agencies.
• Install all electrical connections to local code.
• Use only electrical wire of sufficient gauge and insulation to handle the rated current demand. All
wiring must meet local codes.
• Route electrical wiring along a protected path. Make sure they will not be damaged by moving
equipment.
• Protect components from damage, wear, and harsh environment conditions.
• Allow ample room for maintenance, panel accessibility, and cover removal.
• Protect equipment with safety devices as specified by applicable safety regulations
• If safety devices must be removed for installation, install them immediately after the work is
completed and check them for proper functioning prior to returning power to the circuit.
Failure to follow this instruction can result in serious injury or equipment damage
Additional Reference Materials
Important Information
•IEC - International Standards and Conformity Assessment for all electrical, electronic and related technologies.
•IEC 60364 - Electrical Installations in Buildings.
•FAA Advisory: AC 150/5340-26 (current edition), Maintenance of Airport Visual Aid Facilities.
•Maintenance personnel must refer to the maintenance procedure described in the ICAO Airport Services Manual,
Part 9.
•ANSI/NFPA 79, Electrical Standards for Metalworking Machine Tools.
•National and local electrical codes and standards.
1.1.2 Intended Use
CAUTION
Use this equipment as intended by the manufacturer
This equipment is designed to perform a specific function, do not use this equipment for other purposes
• Using this equipment in ways other than described in this manual may result in personal injury, death
or property and equipment damage. Use this equipment only as described in this manual.
Failure to follow this instruction can result in serious injury or equipment damage
RELIANCE Omni Light
Safety
2
Copyright © ADB SAFEGATE, All Rights Reserved

1.1.3 Material Handling Precautions: Storage
CAUTION
Improper Storage
Store this equipment properly
• If equipment is to be stored prior to installation, it must be protected from the weather and kept free
of condensation and dust.
Failure to follow this instruction can result in equipment damage
1.1.4 Operation Safety
CAUTION
Improper Operation
Do Not Operate this equipment other than as specified by the manufacturer
• Only qualified personnel, physically capable of operating the equipment and with no impairments in
their judgment or reaction times, should operate this equipment.
• Read all system component manuals before operating this equipment. A thorough understanding of
system components and their operation will help you operate the system safely and efficiently.
• Before starting this equipment, check all safety interlocks, fire-detection systems, and protective
devices such as panels and covers. Make sure all devices are fully functional. Do not operate the
system if these devices are not working properly. Do not deactivate or bypass automatic safety
interlocks or locked-out electrical disconnects or pneumatic valves.
• Protect equipment with safety devices as specified by applicable safety regulations.
• If safety devices must be removed for installation, install them immediately after the work is
completed and check them for proper functioning.
• Route electrical wiring along a protected path. Make sure they will not be damaged by moving
equipment.
• Never operate equipment with a known malfunction.
• Do not attempt to operate or service electrical equipment if standing water is present.
• Use this equipment only in the environments for which it is rated. Do not operate this equipment in
humid, flammable, or explosive environments unless it has been rated for safe operation in these
environments.
• Never touch exposed electrical connections on equipment while the power is ON.
Failure to follow these instructions can result in equipment damage
1.1.5 Maintenance Safety
DANGER
Electric Shock Hazard
This equipment may contain electrostatic devices
• Do not operate a system that contains malfunctioning components. If a component malfunctions,
turn the system OFF immediately.
• Disconnect and lock out electrical power.
• Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component
according to instructions provided in its manual.
Failure to follow these instructions can result in death or equipment damage
UM-5027, Rev. 1.0, 2020/12/10 3
Copyright © ADB SAFEGATE, All Rights Reserved

1.1.6 Material Handling Precautions: Fasteners
DANGER
Foreign Object Damage - FOD
This equipment may contain fasteners that may come loose - torque properly.
• Only use fasteners of the same type as the one originally supplied with the equipment.
• Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product
installation and create safety risk .
• You need to know what base the light fixture will be installed in, in order to chose the correct gasket,
bolts and nuts.
• Bolt type, length, and torque value are determined by type of base, height of spacers used, and clamp
force required in FAA Engineering Brief No 83 (latest revision).
• Due to the risk of bolts vibrating loose, do not use any type of washer with the fixing bolts (such as
split lock washers) other than an anti-vibration washer. Anti-vibration washers as defined in FAA EB
83 (latest edition) must be used. For installations other than FAA, use the base can manufacturer's
recommendations.
• Always tighten the fasteners to the recommended torque. Use a calibrated torque wrench and apply
the recommended adhesive type.
• Obey the instructions of the adhesives necessary for the fasteners.
Failure to follow these warnings may cause the fasteners to loosen, damage the equipment,
potentially to loosen the equipment. This can lead to a highly dangerous situation of FOD, with
potential lethal consequences.
Note
To minimize the risk of errors, the ADB SAFEGATE Sales Representative will have information on which gasket goes
with which base. This information is also provided in the product Data sheets, the User Manuals and the Spare Part
Lists.
CAUTION
Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product installation and
create multiple safety risks.
To obtain a safe and watertight installation the O-ring and retaining bolt stated in the document must be used.
You need to know what base the light fixture will be installed in, in order to choose the correct gasket, bolts and nuts.
Failure to follow these cautions can result in equipment damage or aircraft FOD.
1.1.7 Material Handling Precautions, ESD
CAUTION
Electrostatic Sensitive Devices
This equipment may contain electrostatic devices
• Protect from electrostatic discharge.
• Electronic modules and components should be touched only when this is unavoidable e.g. soldering,
replacement.
• Before touching any component of the cabinet you shall bring your body to the same potential as the
cabinet by touching a conductive earthed part of the cabinet.
• Electronic modules or components must not be brought in contact with highly insulating materials
such as plastic sheets, synthetic fiber clothing. They must be laid down on conductive surfaces.
• The tip of the soldering iron must be grounded.
• Electronic modules and components must be stored and transported in conductive packing.
Failure to follow this instruction can result in equipment damage
RELIANCE Omni Light
Safety
4
Copyright © ADB SAFEGATE, All Rights Reserved

2.0 About this Manual
This document includes information on the RELIANCE omnidirectional 8-inch inset light fixture with a focus on safety,
installation and maintenance procedures.
For more information, see www.adbsafegate.com.
Note
It is very important to read this document before any work is started.
2.1 How to work with the manual
1. Become familiar with the structure and content.
2. Carry out the actions completely and in the given sequence.
2.2 Abbreviations and terms - AGL
Abbreviations and terms Description
FAA Federal Aviation Administration
ICAO International Civil Aviation Organization
IEC International Electrical Committee
ISO International Standardization Organization
ANSI American National Standards Institute
NFPA National Fire Protection Association
AC Advisory Circular (FAA)
ESD Electro-Static Discharge; Electrostatic-Sensitive Devices
LED Light Emitting Diode
PPE Personal Protective Equipment
FOD Foreign Object Damage
Mounting support A piece of equipment, on which the fixture is installed.
Toe-in The toe-in angle is the angle the beam of light makes with the longitudinal axis of the runway or
taxiway.
2.3 Abbreviations and Terms
This document may include the abbreviations and terms listed below.
Abbreviation and term Description
ASP Airfield Smart Power
A-SMGCS Advanced Surface Movement Guidance and Control System
CAA Civil Aviation Authority
CCR Constant Current Regulator
FAA Federal Aviation Administration
ICAO International Civil Aviation Organization
UM-5027, Rev. 1.0, 2020/12/10 5
Copyright © ADB SAFEGATE, All Rights Reserved

Abbreviation and term Description
IEC International Electrotechnical Committee
ILCMS Individual Light Control and Monitoring System
LED Light Emitting Diode
LMS Light Monitor and Switch unit
NATO North Atlantic Treaty Organization
NCU Network Concentrator Unit
SCF Series Circuit Filter
SCM Series Circuit Modem
SMGCS Surface Movement Guidance and Control System
SSU System Switch Unit
STAC Service Technique de l'Aviation Civile (France)
STANAG Standardization Agreement (NATO)
RELIANCE Omni Light
About this Manual
6
Copyright © ADB SAFEGATE, All Rights Reserved

3.0 General Information
WARNING
Read installation instructions in their entirety before starting installation.
•Become familiar with the general safety instructions in this section of the manual before installing, operating,
maintaining or repairing this equipment.
•Read and carefully follow the instructions throughout this manual for performing specific tasks and working with
specific equipment.
•these warnings may result in serious injury or equipment damage.
Figure 1: RELIANCE Omni, 4 prisms
3.1 Introduction to RELIANCE
RELIANCE - the all in one revolution
The RELIANCE omnidirectional light light is a low protrusion light-emitting diode (LED) fixture, available in three versions:
RELIANCE A LED light fixture with integrated fail open technology with CCR monitoring
compatibility
RELIANCE IQ A RELIANCE with additional and integrated intelligence (IQ) in a built-in converter for
individual monitoring and control, based on RELIANCE Intelligent Light Control and
Monitor System (ILCMS)
RELIANCE IQ0 RELIANCE IQ light fixture with disabled IQ (ILCMS) functionality. Non-MON light fixture
with possibility to activate IQ at a later stage
NOTICE
RELIANCE IQ light fixtures are not fail-open light fixtures. When IQ is activated the monitoring as well as the control
functionality is handled by the ILCMS system.
UM-5027, Rev. 1.0, 2020/12/10 7
Copyright © ADB SAFEGATE, All Rights Reserved

3.2 LED Apron Maneuvering
Compliance with Standards (current versions)
ICAO Annex 14, Volume 1
IEC 61827
EASA CS-ADR-DSN
Canada TP 312
Australia MOS 139
Uses
The RELIANCE™ 8-inch omnidirectional low-protrusion inset LED light fixture is provided with red or yellow LEDs. This fixture
can be used in the following applications:
•Aircraft Stand Maneuvering Guidance
Features and Benefits
Efficiency •RELIANCE IQ with integrated intelligence
•RELIANCE with integrated fail-open technology
•Operates on CCRs designed in compliance with IEC or FAA requirements
•Easy maintenance due to modular design, few mechanical parts
•No visual flicker. PWM is used for some applications to optimize the LED performance and light fixtures
show no visual flickering.
Sustainability •Light-emitting diode (LED) technology that offers a long-lasting light source with low power consumption
•IP68 protected, anodized aluminum housing designed for harsh weather environments (all fastenings in stainless steel)
•Protected top cover for improved durability and protection from external forces
•Compatible with existing infrastructure
•Fixture compatible with all ADB SAFEGATE 8-inch bases
Safety •Light engine protected against towbar impact and high load upon maneuvering vehicles and aircrafts
•Shorted LED detection according to FAA Engineering Brief No.67D
•Available with IR as an option
Accessories
Refer to the RELIANCE inset user manual for 8-inch lights.
Power Supply
An integrated, encapsulated 6.6A electronic converter. Two-pole L-823 FAA Style 6 (2-pin) plug for connection to the
transformer. Power factor typically > 0.95 at 6.6 A. Power consumption 35 W.
French (flat 3-pin) plugs are also available for the French market.
RELIANCE Omni Light
General Information
8
Copyright © ADB SAFEGATE, All Rights Reserved

Note
•Refer to the appendix of RELIANCE inset user manual for 8-inch lights for a complete power table and the cable
loss formula.
•Refer to the annex section.
Maintenance and Installation
Refer to the RELIANCE inset user manual for 8-inch lights and to the interoperability information for installation in a specific
base.
Dimensions and Weight
Outer diameter / depth Approx. 203 mm / 81.35 mm
8 in / 3.2 in3
Weight without packaging Approx. 2.8 kg
6.1 lb
Operating Conditions
Operating temperature -60 °C to +55 °C / -76 °F to +131 °F
Storage temperature -60 °C to +80 °C / -76 °F to +176 °F
Relative humidity Up to 100%
Note
Deep base and / or adapter rings to be ordered separately.
For more information about the product, including manuals and certifications, please see our Product Center on the ADB
SAFEGATE website: www.adbsafegate.com.
3.3 LED Taxiway Edge
Compliance with Standards (current versions)
FAA L-852T(L)
ICAO Annex 14, Volume 1
IEC 61827
EASA CS-ADR-DSN
Canada TP 312
Australia MOS 139
US Navy NAVAIR 5150AAA-2, WP 006-04
UFC 3-535-01
UM-5027, Rev. 1.0, 2020/12/10 9
Copyright © ADB SAFEGATE, All Rights Reserved

Uses
The RELIANCE™ 8-inch omnidirectional low-protrusion protected inset LED light fixture is provided with blue or yellow LEDs.
This fixture , with an infrared (IR) option, can be used in the following applications:
•Taxiway Edge, L-852T(L)
•NAVAIR Edge
•UFC Edge
•Intermediate Holding Position (MOS)
Features and Benefits
Efficiency •RELIANCE IQ with integrated intelligence
•RELIANCE with integrated fail-open technology
•Operates on 3- or 5-step ferroresonant or thyristor CCRs designed in compliance with IEC or FAA
requirements
•Easy maintenance due to modular design, few mechanical parts
Sustainability •Light-emitting diode (LED) technology that offers a long-lasting light source with low power consumption
•IP68 protected (all fastenings in stainless steel)
•Protected top cover for improved durability and protection from external forces
•Compatible with existing infrastructure
•Fixture compatible with all ADB SAFEGATE 8-inch bases
Safety •Light engine protected against towbar impact and high load upon maneuvering vehicles and aircrafts
•Shorted LED detection according to FAA Engineering Brief No.67D
•Available with IR as an option
Accessories
Refer to the RELIANCE inset user manual for 8-inch lights.
Power Supply
An integrated, encapsulated 6.6A electronic converter. Two-pole L-823 FAA Style 6 (2-pin-) plug for connection to the
transformer. Power factor typically >0.95 at 6.6 A. Power consumption 12 W.
French (flat 3-pin) plugs are also available for the French market. Please check ordering code.
Note
•Refer to the appendix of RELIANCE inset user manual for 8-inch lights for a complete power table and the cable
loss formula.
•Refer to the annex section.
Maintenance and Installation
Refer to the RELIANCE inset user manual for 8-inch lights and to the interoperability info for installation in a specific base.
RELIANCE Omni Light
General Information
10
Copyright © ADB SAFEGATE, All Rights Reserved