INNOVAPLAS MAJESTIC 8000 WITH DECK User manual

REV. 03/05/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
Sand
15 lbs
Sand
Contents of accessory box Majestic step Shell
(not included)
x6
x2
x4
AB
x6
1) Insert the two 39’’ posts
into the step recesses and
secure them in place with
the bolts, washers and
nuts provided.
2) Slide the deck support
on the top post. Do not
secure yet.
3) Insert the handrail over
the posts. Secure it using
the screws provided.
B3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely.
.
CAUTION Failing to install the Step CupTM system will greatly reduce the steadiness of the step and will void the
manufacturer warranty.
Insert the six Step CupsTM in the holes under
the step.*
B1) Insert half of the Step
Cup mushroom ring in
the hole, at a 45 degree
angle.
B2) With a flat screwdriver, compress the Step
Cup mushroom ring while pushing it into the hole.
WARNING
WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
SCREW BAG 140-0062
x4 x4 x4
(3 IN.)
(1 ¹⁄2 IN.)
x6
(³⁄4 IN.)
x10
AB C D E
MAJESTIC 8000 WITH DECK
Required tools (not included)
Phillips #2
Phillips #3 7/16 wrench
Phillips bit
D
A
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
x4
x4
x4
B
C

REV. 03/05/2020 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
D
C
MINIMUM 1"
POOL DECK ABOVE POOL TOP SEAT
POOL TOP SEAT FLUSH WITH DECK POOL
POOL DECK OFFSET FROM TOP SEAT
POOL DECK OFFSET FROM TOP SEAT
DECK
TOP SEAT
DECK
SPACER BLOCK
NOT INCLUDED
PLATFORM
DECK
AFFIX SPACER BLOCK
ON TOP SEAT
DECK
TOP SEAT
All Step Cups
TM
must be installed.
HOW TO MOUNT
YOUR DECK SUPPORT
FOR YOUR POOL
MAJESTIC 8000 WITH DECK
Sand
15 LB
1) Fill the ballast
with sand. The
approximate weight
should be 15 lbs.
CAUTION
To prevent pool liner puncture, keep a minimum 1" gap
between the pool liner and the rear underside of the step.
Align holes
2) Screw the lid in place
and align the cover ribs
with the holes in the
ballast base.
3) Fasten the cover to the
ballast base with the four
screws provided.
x4
D
x2
D
4) Slowly submerge the
step into the pool. Make
sure you do not damage
the pool liner in the
process.
5) Angle the whole step
so that it is entirely under
water. Purge all the air
from under the steps.
6) Slide the deck support
to the height of the deck.
D
E
E
x6
1) Affix the deck support to the deck
with the screws supplied.
2) Install the post cover on the
handrail.
3) Pull the deck support (already
fixed to the deck) upwards to create
a spring effect on the step.
4) Fasten the support to the rear
post while pushing the entire step
downwards.
5) Drop the ballast in the step hole.