AddBike V4.1 Manual

Non-contractual Photographs
AddBike User's and Installation Guide
May 2018
Applicable to the AddBike V4.1
This document indicates the correct practices to be respected during use and assembly / disassembly
of the AddBike. It is imperative to read this document entirely in order to keep your bike and your
AddBike in good working conditions for as long as possible.
Please keep this AddBike User’s Guide.

2VERSION V4.1
The AddBike is an innovative solution that transforms your bike into a practical, easy to handle
cargo bike. It consists of a two-wheeled base that allows the transportation of loads and the
installation of modules specifically designed for the AddBike. These modules give your bike
the capacity to carry bulkier loads, groceries or a child.
Welcome to the big family of AddBikers!!
There is no need to invest in expensive and large cargo bicycles. With the AddBike you can
quickly and easily turn your own bike into a compact cargo bike.
This version of the AddBike is compatible with the following modules:
•Carry’Box V4.1
•Carry’Box Kid V4.1
•Carry’Shop V4.1
Maximum capacities
Load
35 kg
Dimensions (LxWxH in cm)
Overall AddBike
68 x 54 x 83
Base volume available
45 x 32 x 60

VERSION V4.1 3
Table of Contents
1. General warning.......................................................................................................................................4
2. Lexicon of the AddBike.........................................................................................................................6
3. Advises for using the AddBike safely..............................................................................................9
4. Content of the AddBike parcel.......................................................................................................11
5. Assembly of the AddBike..................................................................................................................12
6. Installing the AddBike on the original bike...............................................................................17
A. Prepare your bike for the installation of the AddBike...............................................17
B. Installing the AddBike .............................................................................................................18
7. Security check before every use ....................................................................................................26
8. Good maintenance of your AddBike............................................................................................28
A. Periodical maintenance ..........................................................................................................28
B. Brakes.............................................................................................................................................31
9. Using the AddBike ...............................................................................................................................32
A. First use..........................................................................................................................................32
B. Using the AddBike to transport a load............................................................................33
C. Riding the AddBike with loads ............................................................................................34
D. Using the braking system......................................................................................................35
10. Uninstalling the AddBike...................................................................................................................36
A. Uninstalling the AddBike........................................................................................................36
B. Restoring the bike.....................................................................................................................38
11. Cleaning and storage..........................................................................................................................38
12. Guarantee Charter................................................................................................................................38
13. Assistance in case of problem ........................................................................................................38

4VERSION V4.1
1. General warning
Symbols and warnings:
WARNING!
This symbol indicates a hazard that could result in serious injury if the
instructions are not followed.
CAUTIONING!
This symbol indicates a hazard that may result in minor injury if the instructions
are not followed.
ADVICE!
This symbol indicates advice for the use or maintenance of your AddBike
The AddBike is compatible with the majority of bicycles; however, it is necessary to be vigilant
about the condition of the original bike. The latter must be in perfect working order, equipped
with efficient rear brakes and approved in accordance to ISO 4210 norms. The AddBike can
lead to weakening of the steering pivot in case of misuse and non-compliance with the
instructions.
Read and follow the instructions in this guide: Read the entire guide carefully and follow the
instructions to use the AddBike safely. If you do not understand certain indications, please contact
your AddBike dealer or contact AddBike directly at [e-mail]. Please keep this manual
for future reference. It is also important to take into account the directions for use of the bike
receiving the AddBike.
The AddBike Company disclaims all liability in case of non-compliance with the instructions in this
AddBike User's and Installation Guide and in case of modification of the product by the user.
Generic Risks
Like the use of any conventional bike, the use of an AddBike carries risks of injury and damage
(mainly falling). By using the AddBike, you accept full responsibility for these risks. You need to know
and apply the rules and road traffic regulations to ride safely and in full compliance with such rules
at the risk of exposing you to fines other legal persecutions.

VERSION V4.1 5
Using the AddBike
The AddBike is designed to be used in an urban context on asphalt surfaces. Do not try to go down
stairs with it, nor jump over or go off sidewalks higher than 5 cm. Do not use the AddBike on rocky
surfaces or any other surface with bumps or holes.
The AddBike is intended for use in daylight on public roads and bike paths. If you choose to use your
AddBike in the evening, at night or in other circumstances of low visibility, you must use appropriate
lighting as stipulated by pertinent traffic laws.
The AddBike is not designed for intensive use in sand or salt-water environment.
The AddBike is not designed to be stored outdoors for prolonged periods. It must be stored in a dry
and temperate place away from corrosive products.
Having a regular maintenance of the AddBike makes it possible to preserve its original qualities of
use and safety.
It is forbidden to use the AddBike on the following bikes:
•Bicycle with a wheel diameter greater than 29 inches;
•Bicycle with a wheel diameter less than 26 inches;
•Bike with fork axle of 15 and 20mm;
•Bike with only one fork arm;
•Bicycle with road racing handlebars;
•Children’s bicycle
•Carbon fork;
•Fat Bike; Speed Bike (Electric bike with a speed above 25 km / h).

6VERSION V4.1
Rear plaque
Attachment
axle
Gripping
mechanism
Wheel
Brake
Backrest
2. Lexicon of the AddBike
Figure 1 - Lexicon of the AddBike
Figure 2 - Zoom on the gripping mechanism of the AddBike

VERSION V4.1 7
Figure 3 - Brake handle of the AddBike
Figure 4 - Zoom on the braking system

8VERSION V4.1
Figure 5 - The AddBike base

VERSION V4.1 9
3. Advises for using the AddBike safely
Wearing a helmet
Always wear a helmet when using the AddBike to protect your head in case of fall.
Using the parking brake
To ensure safe loading and unloading, we recommend that you use the parking brake on the AddBike
(located on its brake lever) to stabilize the bike. See explanations in chapter 9.D.
The use of the parking brake is also recommended when parking your bike for extended periods.
Check that the parking brake is deactivated before riding with your bike.
Lighting
It is expressly forbidden by traffic regulations to ride at night or in bad weather without lighting. You
must be visible to other road users:
•Put on reflective and clear clothing, turn on the front and back lighting of your bike;
•Lighting and retro-reflector must be present at the rear and front of your bike.
In case of no compatibility between the AddBike and the lighting device of the
original bike, we advise you to install a lightning on the handlebar.
Drive in a way that is adapted to the environment
It is important to adapt the way you drive according to the conditions of use (weight and volume of
the transported load, wind, rain, brightness, etc.).
When using your bike under the rain or on wet surface conditions, take precautions since the braking
distance may increase and the grip may decrease. Also the braking symmetry between the two
wheels can be altered if one of the brake discs is wetter than the other. In this case, the discs should
be cleaned with a dry cloth and a suitable degreaser.
The AddBike is equipped with disc brakes with hydraulic system. When they are
under a lot of pressure, calipers, discs and pads become extremely hot. In case of
contact, a risk of burn is possible. Always wait for the brake to cool down before
maintenance.

10 VERSION V4.1
Always control your speed, avoid gaps
Except to indicate direction changes, always hold the handlebar firmly with both hands to be able to
control your bike as much as possible (depending on road deformations, movements in the
handlebar may change your course).
Respect the safety and the rules of the road
The use of the AddBike is subject to traffic regulations (respect for signs, direction of traffic,
prohibition to use sidewalks, etc.). Respect the traffic laws of the country of use.
Adjusting and checking the original bike
Always remember to control the rest of the bike and make your usual adjustments for maximum
driving comfort.
Inappropriate use of the AddBike may lead to weakening of the steering pivot. Follow carefully the
instructions in this "AddBike User's and Installation Guide" and check the condition of your bike
regularly.

VERSION V4.1 11
4. Content of the AddBike parcel
The box containing the AddBike comprises:
•AddBike’s chassis;
Figure 6 - AddBike’s chassis
•The wheels and brakes set;
Figure 7 - The wheel and brake set
•This V4.1 User and Installation Guide;
•The brakes’ instructions "Tektro Auriga Twin";
•Two transparent protection stickers;
•The AddBike’s cable clamp.
•A 120mm long screw (to replace the original screw if the latter is too short)

12 VERSION V4.1
5. Assembly of the AddBike
Your AddBike comes partially disassembled, so you need to assemble the different parts before
mounting your AddBike on your bike.
This action is to be performed only once in the entire life of the product, except if you wish to
transport it in its original box.
For the assembly of your AddBike, you will need the following tools:
Open end wrench,
size 19
Socket end wrench,
size 19
Allen wrench,
size 2.5
Figure 8 - Tools needed
•Take out all the contents of the box and close it;
•To facilitate assembly, place the AddBike without its wheels on the box (see Figure 9);
Figure 9 - The AddBike without wheel, on the box

VERSION V4.1 13
•Remove the nut from each wheel axle (see Figure 7);
•Mount the wheels on the stub axle. (See Figure 10);
Be very careful to mount the wheels on the correct side by looking at the following
drawing. In other words, the piece which supports the brake is secured on the
back of the main structure (stub axle), the brake cable is oriented upwards and
the arrows on the tires point towards the front.
Figure 10 - Installing the right wheel
•Replace the nut on the wheel axle and tighten them with the socket wrench (for the screw
head, hub side) and the 19 mm open end wrench (for the nut);
•Remove the screws of the distributor at the rear plaque (see Figure 11);
•Attach the hydraulic distributor to the rear plaque of the AddBike using the 2 previously
removed M4x16 BHC screws and the size 2.5 Allen wrench (see Figure 11) by aligning the
green stickers face to face.
•If the wheels have been mounted on the correct side, you should not be able to see the green
stickers.

14 VERSION V4.1
Figure 11 - Attaching the hydraulic distributor
Here is a back view of your AddBike after assembly:
Figure 12 - Back view of the AddBike after assembly
If you have trouble assembling your AddBike, please contact your dealer or contact AddBike directly
at: [e-mail]

VERSION V4.1 15
If you ordered the mudguard option:
It is easier to install the mudguards before attaching the wheels to the AddBike’s chassis
•Check that both mudguards are included in your box.
•Each fender is attached to a caliper bracket (see Figure 4) according to the figure below. Take
into account that the mudguard support does not simply clamps against the caliper bracket but
is positioned around it thanks to a notch (see Figure 13).
Figure 13 - Positioning the mudguard on the wheel

16 VERSION V4.1
Figure 14bis –Position of the silver washers
•Remove both screws from the caliper bracket.
Be sure to hold in place the brake caliper and the silver washers (see Figure 14bis)
located between the caliper and the caliper bracket (these two elements are no
longer held when both screws are removed).
•Position the mudguard and replace by hand the two previously removed screws, tightening
them with an Allen wrench size 5 (see Figure 14).
Figure 14 - Attaching the mudguard to the caliper bracket

VERSION V4.1 17
6. Installing the AddBike on the original bike
You will find a video of the installation and uninstallation of the AddBike on a bike on our website:
www.addbike.fr
The AddBike must be installed and uninstalled as explained. Improper installation
can lead to accidents that could cause serious injury.
For the installation of the AddBike on the original bike, you will need a set of Allen wrench and open
end wrench. Remove your wheel with the appropriate tools (See Figure 15).
Set of open-end wrench (variable
according to your bike)
Set of Allen wrench
(size 4 for the AddBike’s brakes, and
variable according to your bike)
Figure 15 - Tools Needed
A. Prepare your bike for the installation of the AddBike
Check the general condition of your original bike; there should be no visible cracks
and twisted elements. If this is the case, do not install the AddBike on this bike.
Remove any parts interfering with the installation and / or use of the AddBike
Some parts of the bike may interfere with the installation and / or operation of the AddBike. For
example, it is essential to remove the front mudguard, the front basket and the front dynamo. For
other elements, such as the front lighting, it is necessary to check their compatibility with the AddBike
before deciding whether to maintain them or not. If there is a friction between the AddBike and / or
its modules and an element of the original bike, this must lead to the uninstallation and / or removal
of the element in question.

18 VERSION V4.1
B. Installing the AddBike
Step 1: Remove the front wheel from your bike
Your bike with its front wheel
Your bike without its front wheel
Figure 16 - Your bike with and without front wheel
Depending on the brake and attachment system of the front wheel, disassembly may vary.
Therefore, you have to identify the braking system of your bicycle.
•In most cases, bikes are equipped with rim brakes. In this case, to remove the brake system from
the wheel, pull the brake cable out of its housing (see Figure 17).
Figure 17- Disconnecting the front brake of your bike

VERSION V4.1 19
•If your wheel is equipped with a disc brake, be sure to put the shim back between the pads to
avoid blocking the brake.
If in doubt, or for any other brake system, contact your AddBike dealer or a
professional on cycle servicing.
Identify your wheel lock system (quick coupler, screw-nut ...).
•In most cases, the bikes are equipped with a quick release system. To remove the system:
oOpen the quick release lever (see Figure 18);
oLoosen the adjustment nut manually ;
oRelease the wheel.
Quick release in closed position
Quick release in open position
Figure 18 - Quick release system
•If your wheel is equipped with a nut, loosen it with a suitable wrench to be able to
disassemble the wheel.
If your wheel is equipped with a drum brake or a dynamo hub, we advise you to
contact an AddBike dealer or a professional on cycle servicing to disassemble
them.

20 VERSION V4.1
Step 2: Installing the AddBike on the original bike
The AddBike
Your bike without its front wheel
Your bike with the AddBike
Figure 19 - Demonstration on the assembly of the AddBike
It is not necessary to lift the whole bike when installing or uninstalling the
AddBike. Only the front part of the bike is raised or lowered during the different
stages.
Risk of pinching! Be careful not to get your fingers trapped between the
clamping grips and the fork during tipping.
•Place the AddBike in front of your bike with the front edge of the seat touching the floor (see
Figure 20).
Figure 20 - Your AddBike and your bike in position