ADEMCO ASC25 Series User manual

ASC25-INST 1/96
(anEMcaJ
ASC25 SERIES
(ASC25, ASC25R, ASC25~
MICROPROCESSOR BASED ACOUSTIC GLASS
BREAK DETECTORS
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
coverage: 25 ft. (7.6 m] maximum to fanhes! point of glass being
protected. For glass sizes 0“,, 12 x12 (0.3m x0,3m),
tYPes Of II? (0.64cm) Plate, Tempered, Laminated and
wired glass, and 1[8 (0.32cm) Plate glass (DSB).
Mo”nfi.g: Drectly to the cei6ng, on . . opposite wall, or an sdjacent
wall.
lnp”t Powe. 12 VDC (9 VDC min. to 15 VDC max.) 21 mA nominal
012 VDC (24 mA max. in LED latch mode).
Standby: Connect to power sources capable of supplying stand-by
power of 23 mA-H for each hour of required standby time.
4-bo.r minimum standby time required for U.L.
Certificated installations,
Relay Normally Closed reed relay (NCIC). Contacts rated 3.5
watis, 125 mA @28 VDC far DC resistive loads.
Protected by 4.7 ohm resistor in common Cleg.
Temperature -20 to+120aF (-29to +49°C), +32 to +120°F
(W to +49°C) lor U.L. Cefificated installations.
Dime”$ion SASC25: 4.f, HX2.Y WX0.5 D
(105mm Hx65mm Wx2~mm D).
ASC25F 4.8H x3.27 Wx0.7 D(0.2V Dinstalled).
(i22mmHx63mmxW x13mmD)
ASC25R: 3.@ ~am. x0.S D[86mm ream. x21mm).
Accessories: ASC-GBS Glass Break Smulator For Testing.
INSTALMTION CONSIDERATIONS
f40TP Always pr~test the detectors Iocafion using the ASC-GBS Glass
Break Tester.
.Do “et...
–Mount the detector with obstmctions between the glass being protectedand !he
detector.
–For maximum false alarm immunity, do not mount the delector closer than
5ft. (1.5 m) hom the glass when mounting on the same sudace as the glass.
–Mount closer than 2ft. (0.6 m) to heating or coohng outlets; mount as far
away as possible. [f draffs from these outlets blow on the detector, select a
different location for the detector. Use the environmental test procedure to
verify gmd installation locations.
Install on 24-hour protection circuits.
.Hemember...
–The best mounting location is within 25 ft. (7.6m) from the glass, in- line with
the center of the glass, and on the ceiling or opposite wall of the glass being
protected. Do no! exceed maximum ra”9e,
–Range will be reduced i“ areas that a,e acoustically SOH.This may be due to
carpeting, drapes, plants, or other sound absoting materials. The ASC.GBS
Tester should be used to veri~ range in all Installations.
–Glass Break detectors are intended only as perimster protection devices
They should always be backed “p with motion sensors.
–Glass Break detectors are designed to detect the breakage of framsd glass
and may not detect such things as bullet holes, spontaneous breakage 0
glass (with “o imPa.t), and removal of glass.
.Maximum Range:
The maximum detection range is 25 H. (7.6 m) from the faflhe$t corner, {o
glass sizes 12 by 1Y(0.3m by 0.3m) and larger.
rESTING
resting the Location:
Temporarily ~,lacethe detetior flea< the
desired mounting location using Z-sided
tape.
Power the detector using a9V ba[te~.
The detectors LED should remain off.
Activate the deteoors test mode by
nolting ama:]net mounted inside the
top of the simulator case (or use any
contact magnet) to the test point
maeed TorI the outside case sutiace
of the ASC25, and ASC25R, or next 10
the upper fight corner of the detector
f“, the ASC25F.
Ala
I
)-:-<
ASC25F SHOWN
Mode
jSwitch.
The detectors alarm LED will flash for
10 seconds when the test mode is .Sw ‘T mati o“ ASC25&ASC25R
activated. casela,lestamvat,onp.,.!.
The detector will remain in lest mode for 5minutes.
Vote All testi]>gshould be done with the detecto<s cover in place.
rest #1: Environmental Test
)“fing the 5minute tes! mode, the LED will intimte low or high frequency distur-
bancesby flashing .! speci6c rates. Occasional (random) pulses of the LED are
?ormal.To rule!out random pulses affectinfl this test, obsewe the LED for the full
5mfn.tes.
,Turn on all S(,urcesof noise (e.g. !orced air blowers, air cond Ut>ners,compres-
sor mO1Ors,etc.).
IThe LED will (lash 5times per second each time alow hequency disturbance is
detected. [f It,. five flashes per second occur more !han once .vev 35 seconds
or if the unit alarms, !hen do not mount in ttis location.
,The LED will flash once each time atigh Irequency tist”rbance is detetied. If
any flashes occur more than once evew ?5 seconds, do not mount in ttis Iota.
tion.
Remember: If the detector happens to 81arm during this test, the alarm
relay will activate as we!l.
Test #2: Response Test:
lhis lest Shot,ld be preformed using ths ASC-GBS Glass 6reak Tester. The
ASC.G8S produces atigh-frequency !one designed to alarm the unit to fuflher
verifyproper Iocatlon.
Remember: l-he detector must be i“ the test mode to petiorr. this response
test.
CAUTION: D<Inot point the tester at your ear (or anyone el:se,s). Doing so
could damage hearing.
.Hold the ASC-GBS Tester againstthe window being tested and poin! it directly at
the detector.
. If window treatments are installed (cunaios or blinds), operate the Tester
betind them.
.Activate tlle Tester.
Setting the tester to automatic mode ...s.s it to activate e.e~ 6sec.
ends. This will allow you to better obsewe the detectors LEO.
For large windows, peti”rm ttis test at different placements along the win-
dow.
.The alarm/test LEO and the alarm relay will activate for three seconds
if this is an acceptable detector placement.
Note The low frequency response of the de!eclor can be tested (wtile still in the
test mode) by opening adoor about 1inch and slzmming ii shut, The detectof
should Indicate an alarm.
.During the kist 10 seconds of Ihe dete~tor,s lest mode, 16sLE.Dwill pulse. ‘To
end before the 5-minute time-out pedod, momentarily remo”e power to the
detector or re.aontv maunet to test Dolnt.
,,. .

MOUNTING AND SET-UP FOR ASC251ASC25R
Mountthe Detector
After “erifying an acceptable location, permanently mount the detector.
The ASC25 detector requires 2mounting screws. Spacing for mounting holes (3,2&
center to center) matches those 01a sing!e-gang outlet box (not s“ppbed),.
The ASC25R detector an be mounted using the one center screw hole.
Remo”al of the circuit board is not required for mounting of either the ASC25 or
/
ASC25R detector.
MOUNTING ANO SET-UP FOR ASC25F
Mount the Detector
The ASC25F is designed to mount 10a standard
Single.gang electrical box (not supphed), Mount
the box before insta(hngthe detector.
.Remove the front co”er by inseting aflat-blade
screwdriver in the cover latch and p~ing the
co”er o“t and away from the chassis,
Recess Mount Ring:
The ASC25F may also be recess mount.d
without the “se of asingle-gang box by using Iho
S“pphed recess m.””! ting,
.Using the recess mount ring as atemplate,
prepare an open!ng 1.7)V wide by 2.31Y wide
i“ the mo”nti”g sudace,
.Route wiring through opening and ring.
.Place the ring over the ope”i”g and bend the
\
/1
m
Cover Latch (ASC25F)
s.ppoti tabs into the opening and around the mounting suflace so that the ring fits
snug against the wall.
.Connect wiring 8$ shown below,
.Mount the detector to the ring using the supplied screws.
WIRING (ALL UNITS)
CAUTION oNLY APPLY POWERA~ER ALL CONNECTIONSHAVEBEENMADE
AND INSPECTED.
Note: Do not coif excess wire inside the unit,
m
12VDC IN u
A[am
SELECT LED LATCHING MOOE
ON The LED will latch on when the “nit is alarmed and will stay on “nlil i! is
Momentarily interrupt input power or recycle test mode
10,eset the LED.
OFF The LEOwill t“r” on only while the ““it is in alarm, *
Note Ifthe jumper is removed or missing, the LED will
default to the OFF position.
SET-UP ANO TESTING
.Replace the deteclo<s cover, the. apply power.
.Re-test the “nit with the ASC-GBS Glass Break Tester.
FOR SERVICE OR TECHNICAL SUPPORT, CALL
1–80M67-5875
CALL 1-80045&9469 after 6,00PM EST
AMRM DEVICE MANUFACTURING CO.
ADIVISION OF Pl~AY CORPORATION
165 Eileen Way, Syosset, New york I I 7gl
Copyright 01996 Pl~AY CORPORATION
ASC25-INST 1/96 30326C
reset.
. .. . .. .. ..- ... .. . .. . .. .. . .. --------------- ... . .. . .. . .. . . .-- .-m
WARNING
THE LIMITATIONS OF YOUR GLASS BREAK DETECTOR i
,Wh~le this Glass Break Deteclor is ahighly reliable intrusion detectlo. t
~d,ev,ce,II does not,offer g“a{anleed protecfio” against burgla~. Any i“tr.. ~
~slondetecllon device ISsubject to compromise or failure to wam for a“ari. !
!.!” of ,,,s0”s, Fof exam”le,
!. i“tr”de[s may gain aC~eSSthrough unprotected openings or have the~
~technical Sophisticaflo” to bypass a. aIarm ,en%or ., di~con”ect ~n:
slam warnino device.
. . ..
/. Thj. ~ete~t~{ c...ot ~perate properly if it i. .ot i“st.lf~d i“ ac.orda”.~~
fwith the instr.c80”s i“ this iostallatio” manual or the control to wtich it is!
:connected is not operative (because of lack of Dower. malfu”cuon. etc.)~
~This e~”ipment, like other electrical devices, is subject to component~
:failure. Even though this equipme.1 is designed to last as long as 10;
!Years. the electronic component. could fail at any time,
~Themost common cause of a“ alarm system “ot f.”ctioning when an intru. ~
tsion OccUr: ISinadequate maintenance. This de”ice, and the alarm system!
~towMch It !s connected, should be tesled weekly to make sure all is work-}
iing propedy.
~lnst816nga“ alarm may make the owner elgible for alower insurance rate,~
:but an alarm system is “ot as“bstit. te for insurance. Homeowners, prop-:
/edy owners and renters should continue to act prudently in projecting them-:
~sel”es a“d continue to insure their ~“es and propew.
~We continue [o develop new and impro”ed protection devices. Users of~
lalarm systems owe it to lhemsel”es and their Io”ed ones to learn abo.tf
Ithese de”elopme”ts.
--------------------------------------------------------------
ADEMCO SIX YEAR LIMITED WARRANN I
Alarm Oevice Manufacturing Company, aDivision of Pittway
Corporation, and its dvisions, subsidiaries and afiliates ~Selle r’,), 165
Eileen Way, Syosset, New York 11791, warrants this sensor to be in
conformance with its own plans and specifications and to be f,ee f,om
defects in “ate fials a“d workma”smp under normal use a“d se~ice for
72 months from the date stamp control on the product. For the first 12
months, Sellsr’s obligation shall be bmited fo replacing, free of charge for
materials or labor, asensor which is pro”ed not in compliance with
Seller’s specifications or pro”e$ defecti”e in materials or workmanship
under normal use and se~ice. For the balance of the warranty petiod,
Sellers obligation shall be Nmifed to replacing or repairing, at its option,
free of ch~rge for matetials or labor, adefective or non-compliant sensor
aS defined abo”e. Seller shall have no obligation under thiS fimited
Warranfv or othewise if the senseor is altered or improperly repaired or
nAdemco factov sewice. In case of defeciseNtced’ by anyone other thar
in the first ~2months, return the sensor to AD”I or a“ authorized Ademcol
tistrib”tor for a
an Immeti ate replacement. For the balanco of the warran.
ty, return the dafecti”e product, transpoflatio” prep8 id, to Ademco
FactoW Sewice, i65 Gleen Way, Syosset, New York i1791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIEO, OF MER-
CHANTABILITY, OR FITNESS FOR APARTICl ], An PI !RPng .
.,. -3E OR
OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF. IN NO CASE SHALL sELLER BE LIABLE TO
ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, OR UPON ANY 01
ER, EVEN IF THE L
OWN NEGLIGENCk UR FAULT. I
THER SASIS OF LIABILITY WHATSOEV-
LOSS OR DAMAGE IS CAUSED BY THE SELLERS
Seller doe: not represent that the products it sells may not be Compro-i
mtsed or clrc.m”ented; that the products ‘Nill prevent any personal inju~f
or prope fly loss by burglav, robbe~, fire or othemise: or that the prod.
ucts will in all cases pro”ide adequate warning or protection, Customer
understands that aproperly installed and maintained alarm may only
reduce the tisk of ab.rgla~, robbe~, fire or other events occ”rri”g with-
out pro”lti”g an alarm, b“t it is not insurance or ag“ara”tee that such
will “ot occur or that there W(IIbe no personal inj”~ or prope fly loss as a
result. CONSEQUENTLY, SELLER SHALL HAVE No LIABILlm FORI
ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS
BASEO ON ACLAIM THE PRODUCT FAILED TO GIVE WARNING.
Howe”er, if Seller is held liable, whether directly or indirectly, for any
loss or damage arising under this Nmited Warranty or othe~ise, regard-
less of cause or origin, Seller’s maximum Iiabhy shall not in a“y case
exceed the, purchase ptice of the product, whch shall be the complete
and exclusive remedy against Selle,, This warranty replaces any previ-
ous warranties Snd is the only warranty made by Seller on this product.
No increase or alteration, wfltten or “erbal, of the obligations of this
hmded Warranty is authorized.