ADEMCO LYNX User guide

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
Ademco Lynx - System Manual
« Help Center
System
Overview
System
Keywords
Arm &
Disarm the
System
Panic Alarms Trouble
Conditions
User Access
Codes
System
Testing
Other System
Information
System Overview
The Ademco Lynx represents the latest in home and business security protection technology providing
ADT customers with:
Burglary, emergency, and fire* protection
At least one touchpad to control operations and display system status
Sensors for perimeter and interior burglary protection
Smoke or combustion detectors* for early fire warning
Display of zones triggered during alarm
Multiple partition arming/disarming
Up to four programmable pagers
Select

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
Message playback
The Ademco Lynx is designed to be as maintenance free as possible, however we suggest that you still
test your system once a month and after any alarm occurrences.
Treat the system as you would any other electrical equipment; do not slam protected doors or windows,
keep dust from accumulating on the touchpad and sensors, and do not spray water or any liquid on the
units.
System Keywords
Keyword Meaning
Alarm Appears when an intrusion has been detected and the system is armed (also appears
during a fire alarm or audible emergency alarm). Accompanied by the protection zone in
alarm.
Away All burglary zones, interior and perimeter, are armed.
Instant Entry delay is turned off.
Stay Perimeter burglary zones, such as protected windows and doors, are armed.
Fire Appears when a fire alarm or fire fault is present. Accompanied by a display of the zone
in alarm.
Low BAT. Low battery condition in a wireless sensor (if zone number is displayed or low system
battery (if no zone number is displayed). If 00 is displayed, a wireless keypad
(5827/5827BD) has a low battery condition.
AC Appears when AC power is present. If not lit, the system is operating on backup battery
power.
Chime Appears when the Chime feature is activated.
Test Appears when the system is in Test mode.
Rec Appears when in Recording mode.
Message Appears when a message has been recorded and has not yet been played back.
Bypass One or more burglary protection zones have been bypassed.
Fault Appears when a malfunction is discovered in the system at any time; or if any open is
detected in a fire zone at any time; or when a fault in a day/night burglary zone is
discovered during a disarmed period. Accompanied by a display of the zone number in
trouble.
Arm & Disarm the System
Arming

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
Before arming your system, all protected doors, windows, and other protection zones must be closed or bypassed. Pressing the [STATUS] key
will announce all zones that are faulted, as well as any other abnormal system condition, making it easier for you to secure any open zones.
Ready light: The green Ready indicator on the keypad will be lit if the system is ready to be armed. If blinking, the system is not ready.
Press the Status Key
Press the [STATUS] key once to announce the general status of the system. The following phrases may be heard depending on the current
state of the system:
Disarmed, ready to arm [message] [check system]
Disarmed, [not ready to arm], [message]
Armed [away] [stay] [instant] [check system]
Note: Phrases in brackets are variable, and are announced only if appropriate in the current state of the system.
Press the [STATUS] key trice to announce specific system status. The following phrases may be heard depending on the current state of the
system:
Fire alarm [zone voice descriptors]
Alarm [zone voice descriptors]
Fire fault [zone voice descriptors]
Fault [zone voice descriptors]
Low battery [zone voice descriptor]
System low battery
AC loss
Zones bypassed
Chime
System Can Be Armed
The Ready light will be lit when all protection zones have been either closed or bypassed.
You may now arm the system as usual.
Arming in Stay Mode
To arm in stay mode:
1. Enter your security and press the [STAY] button.
2. The keypad will beep three times and display the armed Stay message. The red Armed indicator will
light and the system will announce “armed Stay-exit now.”
Arming in Away Mode
To arm in Away mode:

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
1. Enter your [security code] and press [AWAY].
2. The keypad will beep twice, or continuously if the exit warning has been programmed for your
system, and will display the armed Away message. The red Armed indicator will light and the system
will announce “armed Away-exit now.”
Arming the System with No Delay
Use No Delay with Stay mode when you are staying home and do not expect anyone to use the entrance
door. Use No Delay with Away mode when the premises will be vacant for extended periods of time such
as vacations, etc.
When armed with No Delay, the system will sound an alarm if a protected door or window is opened,
including the entrance door. You may leave through the entrance door during the exit delay period
without causing an alarm, but an alarm will sound as soon as someone reenters.
To arm with No Delay, enter your [security code] and Away or Stay and No Delay.
Disarming
To disarm the system and silence the burglary alarm:
1. Enter [security code] and press the [OFF] button.
2. The Ready light will light (if no alarms have occurred while armed) and the keypad will keep once to
confirm that the system is disarmed.
EXIT/ENTRY DELAY
Your Ademco Lynx provides a delay after entering or exiting your home before the system is alarmed.
Bypassing Protection Zones
Zones (also called partitions) are areas that can be bypassed when arming the system. This could be ideal
for those who want to arm all but one door/window.
Bypassing Protection Zones
Bypassing zones allows you to arm your system with one or more zones intentionally unprotected. The
system must be disarmed before arming. Fire zones cannot be bypassed.
To bypass a zone:
1. Enter your [security code] + [BYPASS] and enter the 2 digit zone number. Important! All single-digit
numbers must be preceded by a zero (for example, enter [02] for zone 2).
2. The keypad will display the word “Bypass” along with each bypassed zone number. Wait for these

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
zones to be displayed, to be sure that the intended zones are bypassed.
3. Arm the system as usual when the keypad displays the Ready LED on steady.
Door Chime (Entry/Exit Beeps)
To turn the door chime function on or off, press [FUNCTION] and [CHIME].
Panic Alarms
Emergency Keys
Your system may have been programmed to use special keys to manually activate emergency (panic)
functions. To activate a panic function, press and hold down the designated lettered key for at least 2
seconds or press both keys of the designated key pair at the same time.
Function Signal to Customer Care Sound Activated
Silent Alarm Silent alarm No audible alarm to indicate
silent alarm has been activated
but message sent to Customer
Care
Audible Alarm Audible alarm A loud, steady alarm on touchpad
and any sounders
Personal Alarm Emergency alarm Steady alarm at touchpad
Fire Alarm Fire alarm Pulsing sound at external bells
and sirens
Trouble Conditions
Trouble conditions are indicated by the word CHECK and continual beeping from the touchpad. Any key
will silence the beeping. A display of CHECK + zone no. may indicate that a problem requires your
attention. Check the specified zone area, close any open doors or windows and enter your security code
and press [OFF]. If your system includes wireless sensors, the CHECK condition may be caused by some
change in the environment of the protected area.
To silence trouble beeps, press any key or enter your security code and press [OFF].
For a complete list of Trouble Conditions, please refer to the Ademco Lynx & QuickConnect
Troubleshooting page
User Access Codes

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
Access Code Programming
Your system allows for up to 6 user codes for use by other users, however only the master user of the
system is the only one who can assign codes to secondary users, and is designated user no. 02; user no.
01 is the installer’s code.
Babysitter Code (User 07): This code can be used to arm the system, but cannot disarm the system
unless the system was armed with this code. This code is typically assigned to someone (such as a
babysitter) who needs to arm/disarm the system only at certain times. The Babysitter Code is assigned to
User 07.
Duress Code (User 08): This feature is intended for use when you are forced to disarm or arm the system
under threat. When used, the system will act normally, but can silently notify the alarm monitoring
company of your situation, if that service has been provided Duress Code is assigned to User 08.
The Duress Code is useful only when the system is connected to an alarm monitoring company.
To Add/Delete a User or Change a User's Code
To add a user code:
1. Enter the [Master code] and press the [CODE] key.
2. Enter the user number and the user’s code (03-08).
To delete a user code:
1. Enter the [Master code] and press the [CODE] key.
2. Enter the user’s code (03-08).
3. Wait 3 seconds until the keypad beeps once before pressing any other key. The code will
automatically be deleted.
System Testing
Testing Your System
Testing allows for each protection point to be checked for proper operation. While the touchpad will beep
every 45 seconds during Test Mode, no alarm messages will be sent to the Customer Care Center. We
recommend testing the system once a week.
To Test the System:
1. Disarm the system.
2. Close all protected windows, doors, etc.
3. The “Ready” message should be displayed the green Ready indicator (if present on the keypad)

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
should also be lit.
4. Enter your [user code] and then press [TEST].
5. The external sounder should sound for 2 seconds and then turn off.
FAULT ZONES. Open each protected door and window in turn and listen for three beeps from the
keypad. Identification of each faulted protection point should appear on the display. The display will clear
when the door or window is closed.
Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the
detector should appear on the display when it is activated, and its voice descriptor will be announced (if
programmed). The display will clear when no motion is detected. Note that if wireless motion detectors
are used, there is a 3-minute delay between activations. This is to conserve battery life.
To test all smoke detectors, follow the manufacturer's instructions. The identification of each detector
should appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no display), notify your
service company.
When all protection points have been checked and are intact (closed), there should be no zone
identification numbers displayed on the keypad
Exit Test Mode
When testing is completed, exit the Test Mode by entering your [security code] and pressing the [OFF]
key.
If the Test Mode is inadvertently left active, it will automatically turn off after 4 hours.
To learn more about testing your system, please visit System Testing.
Other System Information
For a more detailed description of these features, please refer to the manufacturer’s complete manual.
Time & Date Programming
Your system can display the current time. The date is not displayed, but has an internal function. The
system must be disarmed with no faults present.
To set the time and date, enter the [Master code] and press [FUNCTION] and enter [63].
NOTES:

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
1. The keypad beeps twice for invalid data entries (e.g., an hour greater than 12), and the entry will not
be accepted. The keypad beeps once for valid entries.
2. Clock-Setting mode automatically ends if no keys are pressed for one minute.
3. Daylight savings time may have been programmed to automatically begin and end.
1. Hour (The current hour will be displayed with the AM/PM indication.)
Enter the 2-digit hour (i.e., 01-12).
Press [*] to accept the entry and continue to the AM/PM selection.
Press [#] to exit Clock-Setting mode (keypad beeps 4 times).
2. AM/PM (The current AM/PM setting will display A or P.)
Enter 1 for PM or 0 for AM.
Press [*] to accept the entry and continue to the minute selection.
Press [#] to return to hour-setting prompt.
3. Minute (The current minute will display.)
Enter the 2-digit minute (i.e., 00-59).
Press [*] to accept the entry and continue to the month selection.
Press [#] to return to AM/PM setting.
4. Month (The current month will display.)
Enter the 2-digit month designation (i.e., 01-12).
Press [*] to accept the entry and continue to the day selection.
Press [#] to return to the minute setting.

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
5. Day (The current day of the month will display.)
Enter the 2-digit day of the month (i.e., 01-31).
Press [*] to accept the entry and continue to the year setting.
Press [#] to return to the month setting.
6. Year (The current year will display.)
Enter the last two digits of the year (i.e., 00-99).
Press [*] to accept the entry and exit Clock-Setting mode (keypad beeps 4 times).
Press [#] to return to the day setting.
Message Recording/Playback/Volume Control
The ADT Ademco Lynx Security System Message Center allows you to record, play and delete messages.
The maximum message duration is 85 seconds.
NOTES:
1. The Record/playback functions can only be performed from the master keypad. It cannot be
performed from any other wireless keypad.
2. If the system loses electrical power, all messages will be erased.
3. Message Play/Record will not be available if a report must be sent.
4. Individual messages cannot be played back or deleted.
Recording a Message
To record a message:
1. Press [FUNCTION] + [RECORD].
2. The keypad displays "REC MESSAGE." Begin speaking into the microphone.
3. The recording will automatically stop after 85 seconds, if a message has been recorded. The keypad
will beep twice and "REC" will no longer be displayed. "MESSAGE" will still be displayed.
4. To stop recording before the end of 85 seconds, press [OFF].
5. The keypad beeps twice, the REC display turns off, but the MESSAGE display remains on.
6. Additional messages can be recorded, as long as there is recording time remaning, by repeating the
above steps.
NOTE: If you are trying to record a new message and the message center is already full, the

Ademco Lynx System Manual
http://alpha.adt.com/help/261[11/14/2018 8:02:22 PM]
system will announce "END MESSAGE" and "REC MESSAGE" will not be displayed. If the
message center is full all old messages must be deleted before new messages can be recorded.
See Deleting Messages section.
Message Playback
The lighted word MESSAGE indicates that a new message is in memory. After playing the message, the
MESSAGE display turns off.
To play a message, press [FUNCTION] + [PLAY].
All recorded messages will be announced sequentially. A short beep will sound between messages.
To skip a message, press [*].
NOTE: If a wireless keypad has been installed and is programmed for quick arming, it cannot
be used to activate message playback or adjust the volume. In this case, you must use the
master keypad to perform these functions.
Deleting Messages
To delete all messages:
1. Press [FUNCTION] + [PLAY].
2. While the messages are being announced, press [FUNCTION] + [DELETE].
3. A double beep will sound confirming that the messages have been deleted.
Adjusting the Volume
The volume level of message playback, system announcements, and status beeps can be changed. You
can also mute system announcements if desired.
To adjust message playback/system announcement volume:
1. Press [FUNCTION] + [VOLUME] + [3] to increase or [6] to decrease volume level.
2. Repeat the key sequence until the desired volume level is achieved.
To mute system announcements:
1. Press [FUNCTION] + [VOLUME] + [OFF].
2. The volume level will be restored to the level that was selected prior to muting the sound.
Paging Features
Automatic Paging