Adidas ADBE-10347 Owner's manual

ADIDAS ESSENTIAL ELITE STATION
ADBE-10347
Important – Please read these instructions fully before assembly or using
Assembly & User Instructions - Please keep for future reference

Components - Parts
Note: Some of the smaller components may be pre-tted to larger components. Please check carefully
before contacting Argos regarding any missing components.
1. Main upright × 2
4. Front stabilizer × 1
5. Crossbar × 1
2. Main tube × 1
3. Front leg × 1
6. Support tube× 1 7. Mount tube × 2
8. Left mount tube × 1 9. Right mount tube × 1
11. Seat upholstery × 1
17. Foam roller × 4 40. Bolt cap × 2
34. Flye arm × 2 48. Flye handle × 2 57. M8×20mm Sleeve × 2
49. Pivot bracket × 2
10. Bar holder × 2
12. Rear upholstery × 1
Please check you have all the parts listed belows
45. Pull pin [L] (M10×30mm) × 1 44. Pull pin [L] (M10×55mm) × 1 43. Pull pin [L] (M10×90mm) × 1
41. Knob bolt M10×55 × 1 42. Knob bolt M10 × 5
15. Leg pivot assembly × 1
14. Leg mount assembly × 1
16. Foam mount tube × 2
46. Bush × 1
13. Support plate × 2

Components - Parts
58. Curl attachment tube × 1
60. Lat attachment tube × 1
59. Curl upholstery × 1
63. Stop plate × 2
70. Snap hook × 1
69. Top hat bush × 2
65. Rubber bumper × 2
61. Weight slide carriage × 1
66. M10×115mm Eye bolt × 1
68. Pulley wheel × 1
67. Lat cable × 1
62. Weight mount bar × 1
64. Lat bar × 1
73. Back pad xed
adjustment × 1
72. Back pad xed
piece × 1

M10 × 135mm Bolt × 2
50
M10 × 45mm Bolt × 2
51
M8 × 70mm Bolt × 2
52
Components - Fixings
Note: Some of the xings are pre-tted to the larger components. Please check carefully before contacting
Argos regarding any missing xings.
M10 × 120mm Bolt × 2
18
M10 × 70mm Bolt × 5
19
M10 × 65mm Bolt × 1
20
05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 1101 15 120 125 130 135 140 145 150 155 160 165 170
Ruler - Use this ruler to help correctly identify the hardware
M10 × 60mm Bolt × 3
21
M8 × 15mm Bolt × 5
24
M10 × 55mm Bolt × 2
22
M8 Washer × 17
M10 × 85mm Carriage bolt × 1
25
M8 × 40mm Bolt × 8
23
M10 Nylon locknut × 16
26
Spring clips × 5M10 × Washer × 31
27
Please check you have all the xings listed belowm
Hex key tool × 1Multi hex tool × 1
M10 × 60mm Carriage bolt × 2 M8 Nylon locknut × 2
54
Spring Washer × 2
71
28 39
53

(2) (3) M10x60mm Bolt
(21) M10 Washers (27)
M10 Nylon locknut (26)
bolt M10× 55 (41).
Step 3
Assembly Instructions
Step 1
(5) (1) (13) M10×70mm
Bolts (19) M10
Washers (27) M10
Nylon locknuts (26) (1).
(3) (4) M8×15mm Bolts
(24) M8 Washers (28).
Step 2

Step 4
(2) (5) M10×60mm Bolt
(21) M10 Washers (27)
M10 Nylon locknut (26).
(2) (5) M10×85mm
Carriage bolt (25) bolt
M10 (42).
Assembly Instructions
Step 6
(8) (9) (2) M10×120mm
Bolt (18) M10 Washers
(27) M10 Nylon locknut
(26) (43) (8) (2) (9).
Step 5
(6) (1) (45) (10) (1).

(11) (8) (9) M8×40mm
Bolts (23) M8 Washers
(28).
Step 9
Assembly Instructions
Step 7
(7) (8) (9) M10×120mm
Bolt (18) M10 Washers
(27) (46) M10 Nylon
locknut (26).
(12) (72) (7) M8×40mm
Bolts (23) M8 Washers
(28) (73) (72) bolt M10
(42).
Step 8

(14) (2) M10×55mm
Bolt (22) bolt M10 (42).
Step 12
Assembly Instructions
Step 10
(14) (15) M10×65mm
Bolt (20) M10 Washers
(27) M10 Nylon locknut
(26). (40) 65mm Bolt
(20) Nylon locknut (26)
(44).
(16) (14) (15) (17) (16)
(39).
Step 11

Assembly Instructions
Step 13
M8×70mm Bolts (52),
M8 Washers (28) M8
Nylon locknuts (54)
(47). M8×20mm
Sleeve (57) M8×70mm
Bolt (52). (49) (47)
M10×60mm Carriage
bolts (53) M10 Washers
(27) M10 Nylon
locknuts (26). (48) (49)
M10×45mm Bolts (51)
M10 Washers (27) M10
Nylon locknuts (26)
(39).
(47) (1) M10×135mm
Bolts (50) M10
Washers (27) Spring
washers (71) bolts M10
(42).
Step 14

Assembly Instructions
Step 15
(59) (58) M8×15mm
Bolts (24) M8 Washers
(28).
(58) (2) M10×55mm
Bolt (22) Knob bolt M10
(42).
Step 16

Assembly Instructions
Step 17
(62) (61) (65) (62) (39)
M10×115mm Eye bolt
(66) M10 Washer (27)
M10 Nylon locknut (26).
(68) (60) M10×70mm
Bolt (19) M10 Washers
(27) (69) M10 Nylon
locknuts (26) (61) (60).
M10 x 60mm Bolt (21)
M10 Washers (27) (63)
M10 Nylon locknut (26).
Step 18

Assembly Instructions
Step 19
(67) (60) (70) (64)
M10×115mm Eye bolt
(66).
(60) (2) M10×55mm
Bolt (22) bolt M10 (42).
Step 20

User Information
Rotate main tube to
upright position.
continued on next page.
Folding for Storage 2
Adjustment
Lift rear upholstery (12)
slightly and extract Pull
pin (45) followed by
Support tube (6). Ret
support tube into required
adjustment hole in Main
uprights and ret Pull
pin. Lower Mount tube
back down onto support
tube. Seat base should
be raised for at bench
and drppped for all other
positions.
Fit leg attachment
and ensure all other
attachments are
removed. Remove Knob
bolt M10 (42) and bolt
(25). Lift rear upholstery
(12) slightly and extract
Pull pin (45) followed by
Support tube (6). Lower
rear upholstery to base.
Folding for Storage 1

Ret Knob bolt M10 (42)
and bolt (25). Rotate Fly
arm and Fly handle to
upright position.
Note: you will need to lift
the rear upholstery to t
bolt.
Folding for Storage 5
Folding for Storage 3
Remove Knob bolt (41).
Fold front leg backward
until it reaches main tube.
Ret Knob bolt (41) to top
of front leg. Ret support
tube (6) into Incline3 hole
of main upright ensuring
it also passes through
the locking hole in front
leg. Ret pull pin (45) to
support tube (6).
Folding for Storage 4
User Information

Exploded Parts Diagram

Part Description Qty
1 Main upright 2
2 Main tube 1
3 Front leg 1
4 Front stabilizer 1
5 Main Crossbar 1
6 Support tube 1
7 Mount tube 2
8 Left mount tube 1
9 Right mount tube 1
10 Bar holder 2
11 Seat upholstery 1
12 Rear upholstery 1
13 Support plate 2
14 Leg mount assembly 1
15 Leg pivot assembly 1
16 Foam mount tube 2
17 Foam roller 4
18 M10 x 120mm Bolt 2
19 M10 x 70mm Bolt 5
20 M10 x 65mm Bolt 1
21 M10 x 60mm Bolt 3
22 M10 x 55mm Bolt 1
23 M8 x 40mm Bolt 8
24 M8 x 15mm Bolt 5
25 M10 x 85mm Carriage bolt 1
26 M10 Nylon locknut 16
27 M10 Washer 31
28 M8 Washer 17
29 50mm Square inner cap 4
30 38mm Square inner cap 4
31 33.4mm Square inner cap 1
32 20 x 40mm Square inner cap 1
33 13 x 26mm Square inner cap 8
34 25mm Round inner cap 10
35 19mm Round inner cap 4
36 38mm Round external end cap 2
37 25mm Round external end cap 3
Exploded Parts Diagram List
Part Description Qty
38 45mm Square sleeve 3
39 25mm Spring Lock 5
40 Bolt cap 2
41 Knob bolt M10 x 55 1
42 Knob bolt M10 5
43 Pull pin [L] (M10 x 90mm) 1
44 Pull pin [L] (M10 x 55mm) 1
45 Pull pin [L] (M10 x 30mm) 1
46 Bush 1
47 Fly arm 2
48 Fly handle 2
49 Pivot bracket 2
50 M10 x 135mm Bolt 2
51 M10 x 45mm Bolt 2
52 M8 x 70mm Bolt 2
53 M10 x 60mm Carriage bolt 2
54 M8 Nylon locknut 2
55 38mm Round inner cap 4
56 25 x 130mm Handle 4
57 M8 x 20mm Sleeve 2
58 Curl attachment tube 1
59 Curl upholstery 1
60 Lat attachment tube 1
61 Weight slide carriage 1
62 Weight mount bar 1
63 Stop plate 2
64 Lat bar 1
65 Rubber bumper 2
66 M10 x 115mm Eye bolt 1
67 Lat cable 1
68 Pulley wheel 1
69 Top hat bush 2
70 Snap hook 1
71 Spring washer 2
72 Back pad xed piece 1
73 Back pad xed adjustment 1

Guarantee
Product Guarantee
This product is guaranteed against manufacturing defects for a period of
This product is guaranteed for twelve months from the date of original purchase.
Any defect that arises due to faulty materials or workmanship will either be replaced,
refunded or repaired free of charge where possible during this period by the dealer
from whom you purchased the unit.
The guarantee is subject to the following provisions:
• The guarantee does not cover accidental damage, misuse, cabinet parts, knobs or
consumable items.
• The product must be correctly installed and operated in accordance with the
instructions contained in this manual.
• It must be used solely for domestic purpose.
• The guarantee will be rendered invalided if the product is re-sold or has been
damaged by inexpert repair.
• Specications are subject to change without notice.
• The manufacturer disclaims any liability for the incidental or consequential damages.
• The guarantee is in addition to, and does not diminish your statutory or legal rights.
Email: T[email protected].
Guarantor: RFE Europa Ltd
8 Clarendon Drive
Wymbush, Milton Keynes
MK8 8ED, UK
Year

用户信息
将主管转动到直立为止。
下页续
折叠存放 2
调节
轻轻地抬起后蒙皮 (12)
并依次抽出拉销 (45) 和
支撑管 (6)。重新将支撑
管装入主立柱上所需的
调节孔中，并重新装好
拉销。将装配管降回到
支撑管上。对于平躺椅，
应抬起座位基座，而对
于所有其他位置，则应
降落之。
装好腿附件，并确保拆
除所有其他附件。拆下
旋钮螺栓 M10 (42) 和螺
栓(25)。轻轻地抬起后
(12) 蒙皮并依次抽出拉
销(45) 和支撑管 (6)。将
后蒙皮降落到基座上。
折叠存放 1
斜躺 3
斜躺 2
斜躺
平躺/
斜躺
背
垫
调
节

重新装好旋钮螺栓 M10
(42) 和螺栓 (25)。将飞
臂和飞手柄转动到直立位
置。
注： 您需要抬起后蒙皮以
安装螺栓。
折叠存放 5
折叠存放 3
拆下旋钮螺栓 (41)。向后
折叠前腿，直到到达主管
为止。
重新将旋钮螺栓 (41) 装
到前腿顶部上。重新将
支撑管 (6) 装入主立柱的
Incline3 孔中，确保其也
穿过前腿中的锁定孔。重
新将拉销 (45) 装到支撑管
(6) 上。
折叠存放 4
用户信息