ADTRAN Express 4100 User manual

Express 4100 and
Express 4110
ISDN Router/Bridge
USER MANUAL
61200176L2-1A
December 1998
Express 4100, Data Only 1200176L1
Express 4110 with POTS Option 1200176L2

Trademark:
DMS-100 is a trademark of Northern Telecom, Inc.
Ethernet is a trademark of Digital Equipment Corporation, Intel Corporation, and Xe-
rox Corporation.
ExpertISDN (patent number 5,715,241) is a trademark of ADTRAN, Inc.
Macintosh is a registered trademark of Apple Computer, Inc.
Novell, NetWare, and Internetwork Packet Exchange (IPX) are registered trademarks
of Novell, Inc.
Windows is a registered trademark of Microsoft Corporation.
5ESS is a registered trademark of LUCENT.
The Express4100and Express4110 incorporateSynchronousData Compression based
on either IBM or hi/fn proprietary intellectual property depending on the time of
manufacture. The following trademarks and copyrights are applicable:
Stacker LZS Compression
Copyright © 1989 Carnegie Mellon University
All rights reserved.
Redistribution and use in source and binary forms are permitted provided that the
above copyright notice and this paragraph are duplicated in all such forms and that
any documentation, advertising materials, and other materials related to such distri-
bution and use acknowledge that the software was developed by Carnegie Mellon
University. The name of the University may not be used to endorse or promote prod-
ucts derived from this software without specific prior written permission. This soft-
ware is provided “as is” and without any express or implied warranties, including,
without limitation, the implied warranties of merchantability and fitness for a partic-
ular purpose.
hi/fn
5993 Avenida Encinas
Carlsbad, CA
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
© 1998 ADTRAN, Inc.
All rights reserved.
Printed in USA.

FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of the FCC rules. On the bottom of
the equipment housing is a label that shows the FCC registration number
and Ringer Equivalence Number (REN) for this equipment. If requested,
provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone
company may temporarily discontinue service. If possible, advance noti-
fication is given; otherwise, notification is given as soon as possible. The
telephone company will advise the customer of the right to file a com-
plaint with the FCC.
3. The telephone company may make changes in its facilities, equipment, op-
erations, or procedures that could affect the proper operation of this
equipment; advance notification and the opportunity to maintain uninter-
rupted service is given.
4. If experiencing difficulty with this equipment, please contact ADTRAN
for repair and warranty information. The telephone company may re-
quire this equipment to be disconnected from the network until the prob-
lem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user serviceable parts.
6. An FCC compliant telephone cord with a modular plug is provided with
this equipment. In addition, an FCC compliant cable appropriate for the
dial backup option ordered is provided with this equipment. This equip-
ment is designed to be connected to the telephone network or premises
wiring using an FCC compatible modular jack, which is Part 68 compliant.
7. The following information may be required when applying to the local
telephone company for leased line facilities.
To ADTRAN service personnel: For continued protection against risk of fire,replace F1
with the same type and rating of fuse only: .2A, 250 V.
Service Type Digital Facility
Interface Code Service Order Code Network Jacks
ISDN 021S5 6.0N RJ-49C

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential environment. This
equipment generates, uses, and can radiateradio frequency energy and, ifnot installed
and used in accordance with the instructions, may cause harmful interference to radio
or TV reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by ADTRAN will void
the user's authority to operate the equipment.
YEAR 2000 Compliance
All Adtran transmission hardware and software have been tested and found to be
fully compliant with the YEAR 2000 requirements. This is true for all models and
revisions regardless of the date of manufacture or delivery.
Users who wish to independently verify that specific products are in compliance may
contact ADTRAN Technical Support at 1-888-423-8726.

CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceedthe Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus," ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Class B prescrites dans la norme sur le materiel brouilleur:
"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.
CANADIAN EQUIPMENT LIMITATIONS
Notice: The Canadian Industry and Science Canada label identifies certified equip-
ment. This certification means that the equipment meets certain telecommunications
network protective, operational, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, ensure that it is permissible to be connected to the fa-
cilities of the local telecommunications company. The equipment must also be in-
stalled using an acceptable method of connection. In some cases, the company’s inside
wiring associated with a single-line individual service may be extended by means of a
certified connector assembly (telephone extension cord). Compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian mainte-
nance facility designated by the supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may give the telecommunications com-
pany cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines, and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or an electrician, as appropriate.
The LoadNumber (LN) assigned to eachterminal device denotes the percentage of the
total load to be connected to a telephone loop which is used by the device, to prevent
overloading. The termination on a loop may consist of any combination of devices
subject only to the requirement that the total of the Load Numbers of all devices does
not exceed 100.

IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be fol-
lowed to reduce the risk of fire, electric shock and injury to persons. The precautions
are listed below.
1. Do not use this product near water (for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool).
2. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the
manual. Do not dispose of batteries in a fire. They may explode. Check local
codes for any special disposal instructions.
SAVE THESE INSTRUCTIONS.

AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL SERVICES
• An affidavit is required to be given to the telephone company whenever
digital terminal equipment without encoded analog content and billing
protection is used to transmit digital signals containing encoded analog
contentwhich are intendedfor eventual conversion intovoiceband analog
signals and transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or billing
information is being transmitted or that the output of the device meets
Part 68 encoded analog content or billing protection specifications.
• End user/customer will beresponsible to file an affidavit with the local ex-
change carrier when connecting unprotected CPE to a 1.544 Mbps or sub-
rate digital services.
• Until such time as subrate digital terminal equipment is registered for
voice applications, the affidavit requirement for subrate services is
waived.

AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO
1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES
For the work to be performed in the certified territory of _______________
(telco name)
State of ________________
County of ________________
I, _____________________________ (name), _____________________
(business address), ____________________ (telephone number) being
duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equip-
ment to be connected to 1.544 Mbps and/or ________ subrate digital services.
The terminal equipment to be connected complies with Part 68 of the FCC
rules except for the encoded analog content and billing protection specifica-
tions. With respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance,
and adjustment of the digital CPE with respect to analog content and encoded
billing protection information continuously complies with Part 68 of the FCC
Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded ana-
log content or billing information which is intended to be decoded within the
telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not
under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the
establishment, maintenance, and adjustment of the encoded analog content
and billing information has (have) been trained to perform these functions by
successfully having completed one of the following (check appropriate
blocks):

( ) A. A training course provided by the manufacturer/grantee of the equip-
ment used to encode analog signals; or
( ) B. A training course provided by the customer or authorized representa-
tive, using training materials and instructions provided by the manufacturer/
grantee of the equipment used to encode analog signals; or
( ) C. An independent training course (e.g., trade school or technical institu-
tion) recognized by the manufacturer/grantee of the equipment used to en-
code analog signals; or
( ) D. In lieu of the preceding training requirements, the operator(s)/main-
tainer(s) is (are) under the control of a supervisor trained in accordance with
_________ (circle one) above.
I agree to provide _________________ (telco's name) with proper documenta-
tion to demonstrate compliance with the information as provided in the pre-
ceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of ________, 199___
_________________________________
Notary Public
My commission expires:
_________________________________