ADTRAN QSFP+ User manual

Q
uic
k
Start
DESCRIPTION
The QSFP+ 40G LR4 Transceiver (QSFP) is designed to be used
with 40 Gbps links over single mode fiber. It integrates four
channels (CWDM DFB laser) and multiplexes them into a single
channel for 40 Gbps optical transmission. On the receiver side,
the module de-multiplexes the 40 Gbps optical signal into four
CWDM channels. Each channel operates at 10.3125 Gbps. The
module can operate at 40 Gbps up to 10 km using 9/125 μm SMF.
The product is compliant with the QSFP+ MSA and IEEE 802.3ba
40GBASE-LR4.
gNOTE
To ensure compatibility, refer to the documentation provided with
the host module.
FEATURES
The QSFP supports the following features:
■4 CWDM Lane Mux/Demux design
■4 channels CWDM DFB
■4 channels PIN photo detector
■Compliant with IEEE Std 802.3 ba,40 G Ethernet LR4
■Compliant with QSFP+ MSA
■Management interface specifications per SFF-8436
INSTALLATION
Before installing the equipment, inspect the QSFP. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
To install the QSFP into an appropriate module, complete the
following steps:
f
CAUTION!
Do not remove the protective end cap from the QSFP until the
fiber optic cable is ready to be connected.
1. Insert the QSFP into the SFP cage on the module. Ensuring
that the latch handle is facing upward, slide the QSFP all the
way into the SFP cage until there is an audible “click.”
wNOTICE
■The latch handle on the QSFP is for removal only. When
removing the QSFP, rotate the latch away from the QSFP, the
QSFP should easily slide out of the cage.
■It is recommended that the protective end cap remains on
whenever the transceiver optical fiber connector is not
inserted.
2. Continue the installation and turn-up of the host module
using the instructions in the documentation provided with the
module or other system-level documentation available
online at www.adtran.com.
ADTRAN Pluggable Optics
QSFP+
QSFP+ 40G LR4 Transceiver
March 2019
61445500F2C-13B
P/N: 1445500F2C

2 61445500F2C-13B
MAINTENANCE
The QSFP does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Refer to the warranty for
further information. Field support for software is provided through
upgrade facilities.
SAFETY AND REGULATORY
ENGLISH
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10 and 1040.11 and IEC 60825-1. This product is
NRTL Listed and CB Certified to all applicable American and
European safety standards. For continued compliance with the
above standards, install only ADTRAN-approved Class 1 Laser
Modules in ADTRAN products. For a list of ADTRAN-approved
SFPs and XFPs, see http:/www.adtran.com/SFP.ADTRAN
cannot certify system integrity with other laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. The
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises.
■Per GR-1089-CORE the ADTRAN system that the SFP is
being deployed in is designed and intended for installation as
part of a Common Bonding Network (CBN). The ADTRAN
system that the SFP is being deployed in is not designed nor
intended for installation as part of an Isolated Bonding Network
(IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (for example,
front panels, SFP/XFP modules) on the product is properly
grounded by way of the backplane connector.
SPECIFICATIONS
Specifications for the QSFP are as follows:
General
■Module type: QSFP+
■Fiber/Copper: Fiber
♦SM/MM: Single mode
♦Single/Dual: 4 TX and 4 RX channels
■Signal data rate:
♦Maximum: 10.3 Gbps per channel
■Optical Connector: LC
■Applications: 40 GBASE-LR4, 40 G Ethernet
■Diagnostic Monitoring: Supported
■Distance:10 km over single-modeFiber
Optical
■Transmitter
♦Laser Diode Type: CWDM DFB Array (4 channels)
♦Tx Wavelengths:
●Lane -1 : 1264.5 to1277.5 nm
●Lane -2 : 1284.5 to1297.5 nm
●Lane -3 : 1304.5 to1317.5 nm
●Lane -4 : 1324.5 to1337.5 nm
♦Tx Power: –4 to +2 dBm at each lane
♦SMSR: >30 dB
♦Extinction Ratio: 3.5 dB
♦Output Eye: Compatible with IEEE 802.3ba 40GBASE-LR4
♦OpticalRisetime(tr):25ps (20%- 80%)
♦OpticalFalltime(tf):25ps (20%-80%)
■Receiver
♦Rx Type: PIN Array
♦Rx Central wavelengths:
●Lane -1 : 1264.5 to1277.5 nm
●Lane -2 : 1284.5 to1297.5 nm
●Lane -3 : 1304.5 to1317.5 nm
●Lane -4 : 1324.5 to1337.5 nm
♦Rx Power: +2.3 to –9.5 dBm
Environmental
■Controlled Protected Environment (Inside)
♦Operational temperature range: –5°C to + 55°C
♦Storage temperature range: –40°C to +85 °C
♦Relative humidity 5% to 85%

61445500F2C-13B 3
gNOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of
GR-1089-CORE.
■This product is designed to be deployed in GR-3108-CORE
environmental class 1.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has also been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental
conditions; Storage Class” 1.2
♦ETSI EN 300 019-2-2 “Classification of environmental
conditions, Transportation”, Class 2.3
♦ETSI EN 300 019-2-3 “Classification of environmental
conditions, Stationary use at weather protected locations”,
Class 3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-1-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
FRANÇAIS
fAVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
Ce produit est un module laser de classe 1 qui est conforme à la
FDA 21 CFR 1040.10 et 1040.11 et IEC 60825-1. Ce produit est
NRTL et Certifié CB à toutes les normes de sécurité applicables
américains et européens. Pour maintenir la conformité avec les
normes ci-dessus, installer des modules laser de classe 1 ne
ADTRAN approuvés dans les produits d'ADTRAN. Pour une liste
des SFP et XFP ADTRAN approuvés, voir http:/www.adtran.com/
SFP.ADTRAN ne peut certifier l'intégrité du système avec
d'autres modules laser.
fATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules SFP / XFP) sur le produit est correctement
mis à la terre via le connecteur de fond de panier.
■Ce produit ne dispose pas d’une connexion c.c. interne entre
le courant de retour de la batterie et la masse du châssis. Ce
produit peut être installé en configuration c.c.-I (isolé) ou c.c.-
C (commun).
gREMARQUE
■Ce produit a été conçu pour répondre aux normes
internationales de sécurité EN 60950-1, AS / NZS 60950,1 et
IEC 60950-1.
■Ce produit est conçu pour répondre aux classes
environnementales suivantes:
♦ETSI EN 300 019-1-1: “Classification des conditions
d'environnement; Entreposage,” classe 1.2
♦ETSI EN 300 019-1-2: “Classification des conditions
d'environnements; Transport,” classe 2.3
♦ETSI EN 300 019-1-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” classe 3.1E
■L'équipement est conçu pour fonctionner sans degradation
lors des tests à tous les niveaux de sévérité, suivant les
spécifications de la classe 3.3 de l'ETSI EN 300 019-1-3.
■Ce produit est conforme à la directive. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2019 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61445500F2C-13B*
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C
VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser -Modul, das mit der FDA 21
CFR 1040.10 und 1040.11 und IEC 60825-1 entspricht. Dieses
Produkt wurde NRTL gelistet und CB Certified allen geltenden
amerikanischen und europäischen Sicherheitsstandards. Für die
ständige Einhaltung der oben genannten Normen, installieren Sie
nur ADTRAN zugelassene Klasse 1 Lasermodule in ADTRAN
Produkte. Eine Liste der ADTRAN zugelassene SFPs und XFPs
finden Sie unter http:/www.adtran.com/SFP. ADTRAN kann nicht
die Unversehrtheit des Netzes mit anderen Laser-Module zertifi-
zieren.
f
VORSICHT!
■Elektrostatische Entladung (ESD) können elektronische
Baugruppen beschädigt werden. Beim Umgang mit Modulen ,
tragen Sie eine Antistatikarmband, um Schäden an
elektronischen Bauteilen zu verhindern. Ort -Module in
antistatische Verpackung, beim Transport oder Lagerung. Bei
Arbeiten an Modulen immer legen Sie sie auf einer
zugelassenen antistatische Unterlage, die elektrisch geerdet
ist.
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, SFP / XFP-Module) auf dem Produkt
richtig über den Backplane-Anschluss geerdet ist.
■Dieses Produkt hat keinen internen Gleichstromanschluss
zwischen Batterierücknahme und Gehäusemasse.
Dieses Produkt kann in einer DC-I (isoliert) oder DC-C
(emeinsam) Konfiguration installiert werden.
g
HINWEIS
■Dieses Produkt wurde entwickelt, um internationalen
Sicherheitsnormen EN 60950-1 erfüllen, AS / NZS 60950,1
und IEC 60950-1.
■Dieses Produkt wurde entsprechend der folgenden
Umweltklassen entwickelt:
♦ETSI EN 300 019-2-1 “Klassifizierung von Umweltbedin-
gunge”; Storage Class 1,2
♦ETSI EN 300 019-2-2”, Klassifizierung von Umweltbedin-
gungen,Transportation”, der Klasse 2.3
♦ETSI EN 300 019-2-3 “Klassifizierung von Umweltbedin-
gungen, Ortsfester Einsatz, wettergeschützten Standorten”
Klasse 3.1E
■Dieses Gerät funktioniert ohne Leistungsabfall während aller
für Klasse 3.3 von ETSI EN 300 019-1-3 vorgeschriebenen
Belastungstests.
■Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen
Sie www.adtran.com für ausführlichere Informationen zu
RoHS/WEEE.
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool)