ADTRAN Total Access 612 User manual

TOTAL ACCESS 612/616/624 (T1 TDM) P/N 4200624L1#TDM
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 64200624L1#T-13A, March 2003 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2003 ADTRAN, All Rights Reserved
Connecting to the Total Access 6xx (T1 TDM)
Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT
interface (on the rear panel of the unit) allows access to the terminal menus
and management features of the Total Access 6xx (T1 TDM).
Perform Steps Below in the Order Listed:
1. Configure a VT100 terminal (or terminal emulation software) with the
following settings:
If the terminal has a parallel setting, disable it and use serial.
2. Connect one end of the 6” data cable (supplied) into the Total Access 6xx
(T1 TDM) CRAFT port. (This connection is RJ-45.) Make the connection to
the VT100 terminal as appropriate for your connection. The pinout for the
DB-9 to RJ-45 adapter follows:
3. Initiate a terminal session and the LOGIN screen displays. By default, there
is no password assigned to the Total Access 6xx (T1 TDM) unit. Refer to
the Total Access 600 Series System Manual for details on assigning a
password to the CRAFT interface.
Data Rate: 9600 baud Stop Bits: 1
Data Bits: 8 Flow Control: None
Parity Bits: None
DB-9 RJ-45 Description
2 5 TX Data - Transmit Data from Unit
3 3 RX Data - Transmit Data from Terminal
5 1 GND - Ground
Status LEDs
The Status LEDs display the status of the network T1, 10/100BaseT interface, voice
connection, and other system parameters for the Total Access 6xx (T1 TDM). For a
more detailed discussion of the front panel LEDs, refer to Section 2, Engineering
Guidelines, of the Total Access 600 Series System Manual.
Connecting Power to the Total Access 6xx (T1 TDM)
The AC powered Total Access 6xx (T1 TDM) comes equipped with a detachable
8-foot power cord with a 3-prong plug for connected to a grounded power receptacle.
Please refer to Section 3, Network Turnup Procedures, of the Total Access 600 Series
System Manual for more detailed instructions.
LED DESCRIPTION
TX/RX Indicates data traffic on the 10/100BaseT interface.
LINK Indicates the status of the 10/100BaseT interface (link up or down).
V.35 RX Indicates received data traffic on the V.35 DTE interface.
V/35 TX Indicates transmit data traffic on the V.35 DTE interface.
DATA Indicates T1 status such as Test, RED alarm, or T1 sync loss.
VOICE Indicates the status of the Voice port.
BATT Indicates the status of the Battery Backup Connection.
PWR NET Indicates the physical status of the T1 interface.
• This unit shall be installed in accordance with Article 400 and 364.8
of the NEC NFPA 70 when installed outside of a Restricted Access
Location (i.e., central office, behind a locked door, service
personnel only area).
• Power to the Total Access 6xx (T1 TDM) must be from a grounded
90-240 VAC, 50/60 Hz source.
• The power receptacle uses double-pole, neutral fusing.
• Maximum recommended ambient operating temperature is 45°C
Reviewing the Front Panel

TOTAL ACCESS 612/616/624 (T1 TDM) P/N 4200624L1#TDM
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 64200624L1#T-13A, March 2003 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2003 ADTRAN, All Rights Reserved
AC Power Connection
Network (T1)
Connection
Life Line
POTS
Battery Backup
Connection
10/100BaseT
Ethernet
V.35 DTE
Connection
Voice Connection
CRAFT Interface
Reviewing the Rear Panel Design
Voice Connection
A single 50-pin female amphenol connector provides the interconnect wiring for
the analog circuits (FXS, FXO). Refer to Section 2, Engineering Guidelines, of
the Total Access 600 Series System Manual for a detailed pinout.
LIFE LINE POTS Pinout
NTWK (T1) Pinout
V.35 Connection
The V.35 DTE interface is compliant with ITU Recommendations through a
standard 34-pin Winchester connector. Refer to Section 2, Engineering
Guidelines, of the Total Access 600 Series System Manual for a detailed pinout.
PIN NAME DESCRIPTION
1,2, 5, 6 UNUSED —
3 RING Life Line Ring Connection
4 TIP Life Line Tip Connection
PIN NAME DESCRIPTION
1 R1 | RXDATA-RING Receive data from the network (RING)
2 T1 | RXDATA-TIP Receive data from the network (TIP)
3 UNUSED —
4 R | TXDATA-RING Transmit data towards the network (RING)
5 T | TXDATA-TIP Transmit data towards the network (TIP)
6,7,8 UNUSED —
CRAFT Pinout
10/100BaseT Ethernet Pinout
Battery Backup Connection
An optional battery backup system is available for the Total Access 6xx (T1 TDM)
(P/N 1175044L1, 2, or 4). Refer to the documentation available for your specific
battery backup unit for more information on this connection.
PIN NAME DESCRIPTION
1 GND Ground - connected to unit chassis
2 RTS Request to send - flow control
3 RXDATA Data received by the unit
4 DTR Data terminal ready
5 TXDATA Data transmitted by the unit
6 CD Carrier detect
7 UNUSED —
8 CTS Clear to send - flow control
PIN NAME DESCRIPTION
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4,5 — Unused
6 RX2 Receive Negative
7, 8 — Unused