Advanced Bionics Naida CI Q90 User manual

029-M520-85 Rev A
© 2015 Advanced Bionics AG. All Rights Reserved. 
AB myPILOT
CI-5900-100
instructions for use
2013
English, Français, Español, Deutsch, Nederlands, Português
Manufactured by:
Advanced Bionics LLC
California, U.S.A.
[phone]
AdvancedBionics.com
Advanced Bionics AG
Laubisrütistrasse 28
8712 Stäfa, Switzerland
[phone]

1
Labeling symbols and their meanings:
European Community Mark of
Conformity. Authorized to affix the CE Mark in
2013
Model
number Date of manufacture
Serial Number Manufacturer
Type of
Protection: B Store at temperatures between -20˚C (-4˚F)
and +55˚C (131˚F)
Fragile Do not get wet
Lot Number See Instructions
for Use
Suitable for atmospheric range between
70kPa and106kPa, which is equivalent to
3000m above sea level to 380m below
sea level.
Suitable for exposure to relative humidity
between 0-95%
Dispose of in accordance with applicable
national and local regulations
The AB myPilot carries a rating of IP40. This
rating indicates that the AB myPilot is protected
against particles greater than 1mm, but is not
intended for use in water.
0
95
IP40

2
Warnings and Cautions
Warnings
• Do not use the AB myPilot remote control when it is
plugged into power sources such as wall outlets.
• Do not use or store the AB myPilot in shirt pockets if
the recipient has a pacemaker, due to a risk of inter-
ference. Contact a health care professional for more
information.
Cautions
• The AB myPilot comes with power supplies specifi-
cally designed for the AB myPilot. Do not use other
power supplies not supplied by Advanced Bionics or a
Phonak distributor. For replacement power supplies,
contact Advanced Bionics.
• Do not use the AB myPilot when instructed not to use
electronic devices on airplanes.
• The AB myPilot should not come within 1 cm (1/2” )
of the Naída CI while stimulating the implant. Doing
so could cause the Naída CI to lose communication
with the AB myPilot. If this happens, power cycle the
Naída CI by briefly removing and then reattaching
the battery.
• If the AB myPilot stops being transmitting commands
to the Naída CI, it might be necessary to re-pair the AB
myPilot with the Naída CI. Follow the steps in the Pair-
ing the AB myPilot section of this user guide.
• If volume commands from the AB myPilot to the Naída
CI seem erratic, position the AB myPilot within 30 cm
(12” ) of the Naída CI. If the problem persists, re-pair
the AB myPilot and the Naída CI.
• The digitally-coded, inductive transmission technology
used in the AB myPilot prevents interference from most
other devices. When operating the AB myPilot near

3
a computer terminal or other strong electromagnetic
fields, it may be necessary to be at least 60 cm (24”)
away to ensure proper operation. If the Naída CI does
not respond to the AB myPilot because of an unusual
field disturbance, move away from the disturbing field.
• Do not use the AB myPilot in locations where it is for-
bidden to use electronic devices.
• X-ray radiation (e.g. CT scans, MRI scans) may
adversely affect the correct functioning of the AB
myPilot. We recommend that you turn the AB myPilot
off before undergoing X-ray procedures and leave it
outside the room.
• The Naída CI and the AB myPilot are given a unique
communication network code during the fitting to
prevent interference from or with Naída CIs worn by
other recipients.
• High-powered electronic equipment, larger electronic
installations and metallic structures may significantly
reduce the operating range.
• Use only original Advanced Bionics accessories.
• Do not make any changes or modifications to the AB
myPilot.
• Opening AB myPilot might damage it. If problems
occur which cannot be resolved by following the
remedy guidelines in the Troubleshooting section of
this user guide, consult your hearing care professional.
• The AB myPilot may only be repaired by an authorized
service center.
• The battery may only be replaced by an authorized
service center.
• Do not remove the cover.

4
AB myPilot
Welcome to a world of remote control access for the
Advanced Bionics Naída CI sound processor with the
elegant and user-friendly AB myPilot remote control and
status reader. The AB myPilot provides easy management
of hearing programs with visual confirmation on a state-
of-the-art color display.
The AB myPilot can be used to adjust both Naída CIs
simultaneously for bilateral recipients, or control both
Naída CIs individually, allowing the recipient to adjust
each sound processor to any specific hearing situation.
For more detailed information, please refer to the more
detailed user guide to benefit from all the features of the
new AB myPilot. For safe handling and usage, carefully
read the Warnings and Cautions in the previous section.
Ask a hearing care professional if you have any questions.

5
Description
On/Off Button
Color LCD
Display Connection
Keypad
Reset
Button
Mini USB
Left (Previous Program)
Up (FlexControl/Volume Up)
Center (Menu/Select/Home)
Right (Next Program)
Down (FlexControl/Volume Down)

6
Getting Started
Charging the Battery and General Battery Information
1
2
The AB myPilot has an
internal rechargeable
battery. To charge it, con-
nect the charging cable
to the AB myPilot.
Plug the other end of
the charging cable into
a power outlet. Do not
use the AB myPilot while
charging.
For safety reasons, recharge the battery only with
chargers supplied by Advanced Bionics.
During the charging process, the battery symbol on
the Home screen will flash. Once the battery is fully
charged, the battery symbol will stop flashing and
remain visible.
Charging an empty battery typically takes about 90
minutes. It is safe to leave the charger connected
overnight—the battery cannot be overcharged.

7
When charging the AB myPilot for the first time, leave it
to charge for five hours, even if the battery symbol stops
flashing.
A new battery’s full performance is achieved only after
two or three complete charge and discharge cycles.
The AB myPilot battery can be charged hundreds of
times. If the operating time of the AB myPilot reduces
substantially, please contact a hearing care professional
or Advanced Bionics.
Turning AB myPilot ON or OFF
Turning On Turning Off
To turn the AB myPilot
On, press and hold the
On/Off button for two
seconds until you see the
display turn On.
To turn the AB myPilot
Off, press and hold the
On/Off button for two
seconds until you see the
display turn Off.

8
For optimal convenience, you can keep the AB myPilot
turned on while wearing the Naída CI. Turning off the
AB myPilot when you switch off the Naída CI, will help to
conserve its charge.
Using the AB myPilot
Pairing the AB myPilot
To begin the pairing process, have the Naída CI you
want to pair within 30 cm (12”) of the AB myPilot.
Attach the PowerCel, Zn-Air Battery Pak, or power
adapter to the Naída CI, commencing the Pairing
Window (five minute time out). If the AB myPilot has
never been paired, upon turning it on, the AB myPilot
screen will read: ‘The AB myPilot needs to be paired
with your hearing instruments.’

9
1
Press the center button to display the main menu.
2
From the main menu, scroll down to select Pairing.
The only option shown on the pairing menu
will be Scan for Devices.

10
3
Select Scan for Devices. The AB myPilot will then find all
the Naída CIs within range. The AB myPilot will tell you
New Pairing Found and the next screen will display the
Naída CI(s) found, which side they are (left or right), and
the recipient’s initials.
4
A check in a green circle indicates that the
Naída CI is paired with the AB myPilot.

11
Unpairing the AB myPilot
1
Select the center button. From the main
menu, select Setting. Note that ZoomControl is not
available on the Naída CI Q30.
2
From the Settings menu, select Pairing.

12
3
From the Pairing menu, select Clear Pairing.
4
The AB myPilot will ask you to confirm. Once you do,
the screen Pairing IDs Reset will be displayed.

13
Finding Paired Naída CI Sound Processors
1
Press the center button, select Settings, select Pairing,
and then scroll down to Find Paired Device.
2
A paired Naída CI will blink its LED. A paired left
Naída CI will blink green four times. A paired right
Naída CI will blink red five times.

14
Standard Mode
The standard mode gives the full overview, including
program, sensitivity, and volume information.
• Press the left or right arrow to scroll back and forth
through the hearing programs.
• Press the up or down arrow to enter the volume
screen. Once in the volume screen, press the left or
right arrow to choose the left or right side, and use
the up or down arrow to increase or decrease the
volume.
• Short press the center button to access the sub-
menus.
• Press the center button for two seconds to change to
the ZoomControl*screen.
If bilateral, when paired to both Naída CIs, all program
changes made by the AB myPilot are applied to both
Naída CI sound processors simultaneously, unless
otherwise specified by the recipient.
The order of the program sequence is set by the hearing
care professional during the fitting process. For further
information on hearing programs, please ask a hearing
care professional.
Status Information
From the Main Menu, the recipient can select Status
*Not available on the Naída CI Q30

15
Info, which lists three options to select from that give the
recipient valuable information about the Naída CI and
AB myPilot status:
• Device Status - The AB myPilot will automatically
readout the Device Status from the closest paired
Naída CI. If a recipient is bilateral, they will need to
move one Naída CI further away from the AB myPilot
in order to get a readout of the other Naída CI.
• Battery Check - Selecting Battery Check allows the
recipient to read the status of both the AB myPilot
and the Naída CI sound processor(s) battery levels. In
order to read out and display battery status
information, the AB myPilot must be within about 30
cm (12”) of the Naída CI.
• AB myPilot Version - Selecting AB myPilot Version will
show the software version the AB myPilot is currently
operating under.
Important information
Maintenance and Care
• Do not attempt to service or modify the Naída CI or
its accessories. Doing so may compromise system
performance and will void the manufacturer’s
warranty. Products should be serviced only at
Advanced Bionics.
• Clean the AB myPilot using a damp cloth. Never use
household cleaning products (washing powder, soap,
etc.) or alcohol to clean the AB myPilot.

16
• When the AB myPilot is not in use, turn it OFF and
store it safely.
• Protect the AB myPilot from excessive moisture
(bathing, swimming) and heat (radiator, car dash-
board).
• Protect the AB myPilot from excessive shock and
vibration.
Safety Notice
Keep the AB myPilot out of reach of children under
three years old.
Interference with Medical Devices
The AB myPilot uses low-power, digitally coded trans-
missions to communicate to the Naída CI.
Although unlikely, interference with medical devices
such as pacemakers is possible.
Interference should not occur with normal use, keeping
the AB myPilot 10 cm (4”) or more away from the body.
Therefore, it is recommended that pacemaker recipients
do not keep the AB myPilot in a shirt pocket.

17
Troubleshooting
Situation Most Probable
Cause Remedy
AB myPilot turns
OFF automatically Battery is depleted Charge AB myPilot
AB myPilot
becomes
unresponsive
AB myPilot may
have encountered
a software problem
Reset AB
myPilot
Screen is white
or dark
Brightness and/or
contrast settings
might be sub-
optimal*
Adjust the
brightness and/
or contrast
settings*
Status information
displayed on AB
myPilot does not
correspond with
current settings in
the Naída CI
Manipulations on
the Naída CI may
not have been
recognized by AB
myPilot
Read out
the status
information as
described on
page 18 of the
user guide
Question mark
symbol is
displayed after
performing the
readout process
AB myPilot may
be out of range of
Naída CI
Move
AB myPilot
closer to Naída
CI
*Not all AB myPilot remote controls have a contrast control

18
Situation Most Probable
Cause Remedy
AB myPilot
commands apply
only to one Naída
CI as opposed
to both
Naída CIs may be
turned OFF
Naída CIs must
be turned ON
to correspond
with AB myPi-
lot. Turn them
ON by attach-
ing PowerCel
to processor
Naída CI
PowerCel may
be depleted
Charge Power-
Cel or replace
Zn-Air batteries
AB myPilot may
be out of range of
Naída CI
Move AB
myPilot closer
to unresponsive
Naída CI
AB myPilot
commands are
not received by
the Naída CI(s)
AB myPilot is too
close or too far
away from Naída
CI(s)
Hold
AB myPilot >
1cm to 30cm
(1/2” -12”)
from Naída CI
and try again

19
No Response Screen
Figure A Figure B
If the AB myPilot scans to find Naída CIs in the sur-
rounding area or tries to do a device status readout or a
battery status readout but is unsuccessful in doing these
tasks, the No Response Screen (Figure A) and ‘Closer
- Try Again’ (Figure B) will be shown. The recipient is
advised to move the AB myPilot and Naída CI closer
together and try the task again.
Recommended Operating and Storage
Temperature Ranges
Condition Minimum Maximum
Operating Temperature 0˚C (32˚F) 45˚C (115˚F)
Storage Temperature -20˚C (-4˚F) 55˚C (131˚F)