Advanced MxPro 4 4100S User manual

www.advancedco.com
4100S
The operation and functions described in this manual are available from Software Version 4100S-023-013 onwards.

www.advancedco.com
Specifications:
Item
Specification Details
Enclosure
Steel IP30
Dimensions H x W x D mm
320 x 345 x 88
Weight (excluding batteries)
5Kg
Temperature
-5°C to 40°C
Humidity
95 % Max
Cable Entries (20mm knockouts)
7x top and 7x top rear
Mains Supply
230V +10%, -15%, 50/60Hz AC, 0.4A max
Battery Capacity
24V 4Ah Internal (min)
24V 7Ah Internal (max)
Charging Current
0.4A Temperature Compensated
Max Battery Resistance (+/-10%)
2.6Ω
Power Supply
On-board 24V DC, 2A High Efficiency Switched Mode
Imax(a) = Imax(b)
1.4A
Output Voltage1
18.0V –32.0V
Ripple (Vpkpk)
3.5V
Number of Fire Zones
100 max
Number of Loops
1
Devices per Loop
Apollo 126 detector/call points per loop (max)
Hochiki 127 detector/call points per loop (max)
Loop Current 2(max. / Loop)
400mA quiescent
500mA alarm
Protocols
Apollo: S90, XP95, Discovery, Explorer & Hochiki ESP
Sounder 2Outputs
2 x 1A Programmable
Relay Outputs
2 x1A 30VAC/DC (max)
10mA 5V (min) Programmable
Open Collector Outputs
2 x Programmable
10mA 30V DC (max)
Digital Outputs
---
Auxiliary Supply Output 2
24V DC, 500mA
Event Log
1000 Event & Diagnostic + 500 Fire
As our policy is one of constant product improvement the right is therefore reserved to modify product specifications without prior notice
1
Minimum/maximum specifications for the AUX, and Sounder outputs. Detector Loop voltage is not dependant on AC or battery voltage.
2
Total output current and panel load should not to exceed Imax(a).

www.advancedco.com
3
Table of Contents Page
1INTRODUCTION.............................................................................................................................................4
1.1 STANDARDS.............................................................................................................................................4
1.2 CAUTIONS AND WARNINGS .......................................................................................................................4
1.3 DESCRIPTION ...........................................................................................................................................4
1.4 EN54 FUNCTIONS ....................................................................................................................................4
1.1 INSTALLATION APPROVALS.......................................................................................................................5
1.1.1 Fire System Installations....................................................................................................................5
1.1.2 Wiring Regulations.............................................................................................................................5
2INSTALLATION..............................................................................................................................................6
2.1 IDENTIFICATION OF PARTS ........................................................................................................................6
2.2 INSTALLING THE ENCLOSURE....................................................................................................................6
2.2.1 Removing and Replacing the Enclosure Cover.................................................................................6
2.2.2 Removing the Chassis.......................................................................................................................6
2.2.3 Mounting the Enclosure.....................................................................................................................7
2.2.4 Remounting the Chassis....................................................................................................................7
2.2.5 Recommended Cable Routing Arrangement.....................................................................................7
2.3 BATTERY INSTALLATION ...........................................................................................................................8
2.4 WIRING INSTALLATION..............................................................................................................................8
2.5 BATTERY STANDBY CALCULATION CHART ................................................................................................8
3PROGRAMMING............................................................................................................................................9
3.1 INTRODUCTION .........................................................................................................................................9
4OPERATION...................................................................................................................................................9

www.advancedco.com
4
1 Introduction
1.1 Standards
Advanced Electronics Ltd declares that the Mx-4100S meets the CE requirements of the following EU
Directives:
Low Voltage Directive 2006/95/EC
EN60950-1: 2006 Safety of information technology equipment
Electromagnetic Compatibility Directive 2004/108/EC
EN61000-6-3:2001 Emissions, Class B
EN50130-4: 1995 +A1:1998 +A2: 2003 Immunity, Product Family Standard
1.2 Cautions and Warnings
STOP
BEFORE INSTALLATION –Refer To the Ratings shown on the label inside
the product and to the ‘Specifications Chart’ in this document.
Please read this manual carefully. If you are unclear on any point DO NOT
proceed. Contact the manufacturer or supplier for clarification and guidance.
Only Trained service personnel should undertake the Installation,
Programming and Maintenance of this equipment.
This product has been designed to comply with the requirements of the Low
Voltage Safety and the EMC Directives. Failure to follow the installation
instructions may compromise its adherence to these standards.
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE DEVICES
This equipment is constructed with static sensitive components. Observe anti-
static precautions at all times when handling printed circuit boards. Wear an
anti-static earth strap connected to panel enclosure earth point. Before installing
or removing any printed circuit boards remove all sources of power (mains and
battery).
1.3 Description
The Mx-4100 is a Single Loop, Analogue Addressable Fire Alarm Control Panel.
The Mx-4100S is designed for use with the Apollo Discovery, Explorer, XP95 and Series 90 and Hochiki ESP
fire detection devices.
The Mx-4100S provides all of the same capabilities as the other panels in the Mx-4000 range but does not have
provision for connection to a network. The panel is a stand-alone unit only.
This manual covers specific information for the Mx-4100S Fire Alarm Control Panel only.
Refer to the Mx-4000 Series User Manual (Document No. 680-015) for details of how to operate the panel.
Refer to the Mx-4000 Series Installation Manual (Document No. 680-014) for all other details on the installation
and programming of the panel.
1.4 EN54 Functions
The available EN54 functions and Options with requirements are fully detailed in manual 680-014.

www.advancedco.com
5
1.1 Installation Approvals
1.1.1 Fire System Installations
The panel must be installed and configured for operation in accordance with these instructions and the
applicable code of practice or national standard regulations for fire systems installation (for example BS5839-1:
2002) appropriate to the country and location of the installation.
1.1.2 Wiring Regulations
The panel and system must be installed in accordance with these instructions and the applicable wiring codes
and regulations (for example BS7671) appropriate to the country and location of the installation.

www.advancedco.com
6
2 Installation
2.1 Identification of Parts
The following diagrams show the major parts of the panels.
2.2 Installing the Enclosure
The panel can weigh in excess of 15kg when the batteries are installed. Use the appropriate
fixing hardware to secure the panel to the wall. Observe recommended lifting practices to
guard against spinal injury.
2.2.1 Removing and Replacing the Enclosure Cover
The enclosure cover is fixed in place with two tamper resistant hexagon key screws. These require the use of a
2.5mm Allen Key. The enclosure cover must be connected to earth. When replacing the cover, always ensure
that the earth lead spade terminal is securely seated onto the blade terminal in the back box.
2.2.2 Removing the Chassis
It is recommended that the chassis be removed before fitting the panel to the wall. To remove the chassis:
Disconnect the earth cable connecting the chassis to the spade terminal on the rear enclosure.
Remove the two screws holding the chassis to the back box. Keep these items in a safe place for later re-use.
Unplug the 3-way connector feeding the power supply to the Base Card. Carefully remove the chassis from the
rear enclosure and place in a safe place to prevent accidental damage.
Do not lift the chassis by holding onto any of the printed circuit cards. Hold the chassis by the
metal plate only.
Earth Lead to
Cover
Chassis
Assembly
AC Mains
Input
Battery
Leads
Rear
Enclosure

www.advancedco.com
7
2.2.3 Mounting the Enclosure
Firstly, remove the required knockouts for the installation wiring. There are sufficient knockouts on the top of the
enclosure for all installation wiring. In addition, there are knockouts at the top of the back wall, if required, for
rear entry cabling.
The enclosure is provided with four fixing points.
The diagram opposite shows the positions of the
four holes. Use all four positions to ensure the
panel is held securely to the wall.
Drill the required holes in the supporting wall using
a drill bit diameter 7.0 mm and plug with a suitable
40mm long expansion plug. Affix the panel to the
wall with M5 screws (length 40mm) or No.10
screws (length 1½”).
Ensure that there is sufficient space to allow the
cover to be removed / replaced when the panel is
mounted.
Finally, use a brush to remove any dust or swarf
from inside the enclosure.
340
270
35
315
274
17
Cable Tie
Anchor Points x6
Earth
Studs x2
Enclosure Size and Fixing Point Dimensions
2.2.4 Remounting the Chassis
Carefully replace the chassis and fix into place using the two screws.
Reconnect the chassis earth cable to the spade terminal in the rear of the enclosure and then reconnect the
supply lead from the transformer to the Base Card.
2.2.5 Recommended Cable Routing Arrangement
It is recommended that the routing
arrangement shown in the diagram
opposite be employed.
Segregate the low voltage wiring (Loop
Circuit, Sounder Circuits and AUX Supply)
from the AC Mains Wiring.
Segregate any wiring connected to the
relay contacts.
Eyelets are provided in the rear of the back
box to enable the cables to be securely
fastened using tie-wraps.
Refer to Manual 680-014 for further
information on cable types to be used.
Refer to specific sections on how to install
AC Mains input and loop, sounder, relay
and AUX outputs circuits.
F
S
2
B
A
T
F
S
1
S
u
p
p
l
y
AC Mains
Relay
Outputs
Sounder
Outputs
Loop
Circuit
Tie-Wrap
Positions
Internal arrangement showing recommended routing of
cables.

www.advancedco.com
8
2.3 Battery Installation
The diagram opposite shows the
recommended location and orientation
for the 7AH batteries within the panel.
For battery sizes greater than 7AH, the
batteries must be installed in a separate
enclosure suitable for fire protection use
with wiring connected to the panel
through rigid conduit.
Replacement Fuses
FS1 T5A 125V Anti-Surge
FS2 T5A 125V Anti-Surge
2.4 Wiring Installation
Refer to Manual 680-014 for further information.
2.5 Battery Standby Calculation Chart
Use the following charts and associated notes to calculate the size of the batteries required to ensure operation
of the installation in the event of AC Mains power failure.
Quiescent Load
Fire Alarm Load
Equipment
I (A)
x
Total
I (A)
x
Total
Mx-4100S
0.115
1.0
= 0.115
0.225
1.0
= 0.225
Sensor / Loop Current3
1.254
=
1.25
=
Mxp-024 LED Indicator –20 Zone
0.003
1.0
=
0.012
1.0
=
Auxiliary Supply Output5
1.0
=
1.0
=
Sounder Output A
1.0
=
Sounder Output B
1.0
=
Total
Quiescent Load
=
Alarm Load
=
x 24 hr =
Ahr
x 48 hr =
Ahr
x 72 hr =
Ahr
x 26x 0.5 hr =
Ahr
(carry forward) +
Ahr
Total Load (Quiescent + Alarm) =
Ahr
x 1.256 (Battery De-rating factor) =
Ahr
3
Use the detector manufacturers’ technical information to calculate the load on the loop for both the quiescent condition and fire alarm
condition for all loop devices. By default, a maximum of 5 detector / call point LED indicators will be turned on in a fire alarm condition. (This
number can be changed via the PC Programming Tool).
4
The calculated loop loading must be multiplied by a factor of 1.25 to calculate the actual current draw from the batteries. This is to take into
account voltage conversion and conversion efficiency in generating the supply for the loop.
5
Refer to separate data sheets for the additional modules that can be powered from the panel AUX Output to determine the AUX loading
currents. For example, the modules can include Modem, Sounder Splitter, Routing Interface, etc. The sum of all these additional currents
should be entered in these fields.
6
The alarm load should be doubled to allow for changes in battery efficiency for loads in excess of the recommended C/20 discharge rate.
The total load calculated should be multiplied by a de-rating factor of 1.25 to allow for changes in battery efficiency over time. The above
calculation is in accordance with the recommendations in BS5839-1: 2002.

www.advancedco.com
9
3 Programming
3.1 Introduction
Full instructions for the configuration and programming of the Mx-4000 Series panels are detailed in Manual
680-014. The following details the features not included in the Mx-4100S panel by menu option.
VIEW
The View –Network option is not available.
SETUP
The network options (This Network Node and Next Network Node) are not available. By default, the panel is
always Node 0 and the panel cannot be connected to a network.
4 Operation
Full instructions for the operation of the Mx-4000 Series panels are detailed in Manual 680-015. The following
details the features not included in the Mx-4100S panel by menu option.
VIEW
The View –Network option is not available.

www.advancedco.com
10
This page is intentionally left blank.

www.advancedco.com
USER NOTES

www.advancedco.com
Advanced Electronics Ltd
Moorland Way, Cramlington, Northumberland, NE23 1WE UK
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.advancedco.com
Doc Number: 680-201
Revision: 01B
First Issued: 2013-mm-dd