Advantech ACP-1320BP User manual

User Manual
ACP-1320BP
1U-high Rackmount IPC Chassis
with Dual SATA Storage Trays

ACP-1320BP User Manual ii
Copyright
The documentation and the software included with this product are copyright 2008 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to
make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel®, CoreTM 2 Duo, Pentium® 4, Pentium® M, CeleronTM, CeleronTM D, CeleronTM
M are trademarks of Intel Corporation.
ACP-1320BP, PCA-6103P2V, PCA-6103P2VX, PCE-5B03V, PCE-7B03V are trade-
marks of Advantech Co., Ltd.
Microsoft® Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Part No. 2002132020 Edition 1
Printed in China September 2008

iii ACP-1320BP User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

ACP-1320BP User Manual iv
Initial Inspection
Before you begin installing your CPU card, please make sure that the following mate-
rials have been shipped:
!ACP-1320 Chassis
!User Manual
!Warranty Card
!Accessory box with a package of screws (for fastening the various disk drives)
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the ACP-1320 mechanically and
electrically before shipment. It should be free of marks and scratched and in perfect
working order upon receipt. As you unpack the ACP-1320, check it for signs of ship-
ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or
it fails to meet the specifications, notify our service department or your local sales
representative immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will make arrange-
ments to repair or replace the unit.

v ACP-1320BP User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-
sure products.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

ACP-1320BP User Manual vi
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

vii ACP-1320BP User Manual
Warnings, Cautions and Notes
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advan-
tech.com
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.

ACP-1320BP User Manual viii
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
–The power cord or plug is damaged.
–Liquid has penetrated into the equipment.
–The equipment has been exposed to moisture.
–The equipment does not work well, or you cannot get it to work according to
the user's manual.
–The equipment has been dropped and damaged.
–The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

ix ACP-1320BP User Manual
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
!To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
!Take anti-static precautions before making any configuration changes. Other-
wise, electrostatic discharges can occur when connecting a jumper or installing
a card or other device; these discharges can severely damage sensitive elec-
tronic components.

ACP-1320BP User Manual x

xi ACP-1320BP User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.3 Power Supply Options............................................................................... 3
Table 1.1: Power supply options for BACKPLANE version ......... 3
1.4 Environmental Specifications .................................................................... 3
Table 1.2: Environment specifications........................................ 3
1.5 Dimension of ACP-1320BP....................................................................... 4
Figure 1.1 Dimension of ACP-1320BP ........................................ 4
Chapter 2 System Setup.......................................5
2.1 Introduction ............................................................................................... 6
2.2 Removing the cover .................................................................................. 6
Figure 2.1 Removing the cover.................................................... 6
2.3 Installing the backplane and the CPU card ............................................... 7
Figure 2.2 Installing a backplane, CPU card and add-on card .... 7
2.4 Installing add-on cards .............................................................................. 8
2.5 Adding disk drives ..................................................................................... 8
2.5.1 Installing a SATA HDD in the SATA HDD tray.............................. 8
Figure 2.3 Removing the front bezel of the drive bay .................. 8
Figure 2.4 Installing a SATA HDD ............................................... 9
2.5.2 Installing a 3.5” HDD/FDD in the 3.5” drive bay and a slim-type CD-
ROM/-RW ..................................................................................... 9
Figure 2.5 Small convert for slim-type optical disk drive............ 10
Figure 2.6 Installing a HDD/FDD and slim-type optical disk in the
3.5” drive bay............................................................ 10
Chapter 3 Operation............................................11
3.1 The Front Panel ...................................................................................... 12
Figure 3.1 Closed front panel .................................................... 12
Figure 3.2 Open front panel....................................................... 12
3.1.1 Switch, Button and I/O Interfaces ............................................... 12
3.1.2 LED indicators............................................................................. 13
Table 3.1: LED indicator functions............................................ 13
3.1.3 LED Indicators for SATA HDD Power & Status .......................... 14
Table 3.2: Table 3.2: SATA HDD LED indicators function for ACP-
1320.......................................................................... 14
3.2 Replacing the Cooling Fans .................................................................... 15
Figure 3.3 Replacing the cooling fans ....................................... 15
3.3 Replacing the power supply .................................................................... 16
Figure 3.4 Changing the power supply ...................................... 16
Chapter 4 Alarm Board .......................................17
4.1 Introduction ............................................................................................. 18
4.2 Alarm Board Layout ................................................................................ 18
Figure 4.1 Alarm board layout ................................................... 18
4.3 Alarm Board Specifications ..................................................................... 18
4.3.1 Connectors, Jumper and Pin Definition ...................................... 19
Table 4.1: CN1, Auxiliary external power connector, standard mini

ACP-1320BP User Manual xii
4-Pin power connector ............................................. 19
Table 4.2: CN4, Thermal sensor (LM75) connector .................. 19
Table 4.3: CN13, Voltage detect input connector...................... 19
Table 4.4: CN16, Power good input connector ......................... 19
Table 4.5: CN17, Alarm reset connector ................................... 19
Table 4.6: CN18, Output connector to LED board .................... 19
Table 4.7: CN26, External HDD LED connector ...................... 19
Table 4.8: FAN1~FAN7, Fan connectors .................................. 19
Table 4.9: J1, External buzzer................................................... 19
Table 4.10:SW1, Fan number select switch............................... 19
4.3.2 Switch Settings ........................................................................... 20
Table 4.11:SW1. Fan number setting......................................... 20
4.4 Thermal Sensor ...................................................................................... 20
Figure 4.2 Thermal sensor location ........................................... 20
Figure 4.3 Thermal sensor module............................................ 21
Table 4.12:CN1 & CN2, Temperature sensor connector ........... 21
Table 4.13:SW1, Thermal sensor I.D. number setting ............... 21
Appendix A Exploded Diagram ............................ 23
A.1 Exploded Diagram .................................................................................. 24
Figure A.1 Exploded Diagram.................................................... 24
Table A.1: Parts List .................................................................. 24
Appendix B Backplane Options ........................... 25
B.1 Backplane Options.................................................................................. 26
Table B.1: PICMG1.3 Backplane Options ................................. 26
Table B.2: PICMG1.0 Backplane Options ................................. 26

Chapter 1
1General Information

ACP-1320BP User Manual 2
1.1 Introduction
ACP-1320BP is a compact, rugged 19” rackmount industrial computer chassis
designed for space-conscious applications. With only 1U height, ACP-1320BP can
accept versatile 3-slot passive backplanes and two full-sized PCI cards via back-
planes.
Dual front-accessible SATA HDD trays
ACP-1320BP comes with two easy-to-maintain SATA HDD trays, which provides the
most economic solution for data mirroring. Users can easily replace a SATA HDD
without opening the chassis top cover. Other data storage options include one slim-
type optical disk drive and one 3.5” HDD bays with shock-resistant protection. Also,
the front accessible USB I/O interfaces can be connected with various peripheral
devices for data input, backup, and transferring.
Unique alarm detection and notification to reduce system down time
ACP-1320BP has the unique alarm module. This module automatically detects the
system operating conditions, such as HDD, FAN, and system temperature, and it
shows the system status on the front LED indicators. Once any failure happens, the
module also gives both audible and visible alarm to notify users to take necessary
actions.
And more
ACP-1320BP comes with a 300W ATX 1U-high power supply; a 250W power supply
is available for customized projects. Streamlined with an efficient cooling design, the
in-chassis airflow keeps the system from over-heating. All these outstanding features
make ACP-1320BP the best choice for price, performance, and total cost of owner-
ship.
1.2 Specifications
!Construction: Heavy-duty steel
!Disk drive capacity: Two front-accessible SATA trays, one slim-type optical
disk drive, and one 3.5” drive bay for FDD or HDD
!I/O interfaces on front panel: Dual USB ports
!I/O interfaces on rear panel: One D-SUB 9-pin opening
! Indicators on front panel: LEDs for Power, HDD, TEMP, FAN LAN 1 and LAN 2
!Switches on front panel: ATX system switch, system reset and alarm reset
!Cooling fans: Three 4 cm x 4 cm (24 CFM) + one 4 cm x 4 cm (14 CFM) cool-
ing fans
!Expansion: Supports two full-sized add-on cards
!Weight: 8.2 Kg (18.1 lb) with 300W power supply
!Dimensions: 480 mm (W) x 44 mm (H) x 620 mm (D) (19" x 1.7" x 24.3")

3 ACP-1320BP User Manual
Chapter 1 General Information
1.3 Power Supply Options
1.4 Environmental Specifications
Table 1.1: Power supply options for BACKPLANE version
Model Name 1757001797 1757000160G
Watt 250 W max. (ATX, PFC)
(single power)
300 W (ATX, PFC)
(single power)
Input Rating 100 ~ 240 Vac (Full range) 100 ~ 240 Vac (Full range)
Output
Voltage
+5 V @ 23 A, +3.3 V @ 14 A,
+12 V @ 16 A, -12 V @ 0.5 A,
-5 V @ 0.2 A, +5 Vsb @ 2 A
+5 V @ 25 A, +3.3 V @ 14 A,
+12 V @ 16 A, -12 V @ 1 A,
-5 V @ 0.5 A, +5 Vsb @ 2 A
Minimum
Load
+5 V @ 3 A, +3.3 V @ 1 A,
+12 V @ 2 A, -12 V @ 0.1 A,
-5 V @ 0 A, +5 Vsb @ 0.1 A
+5 V @ 3 A, +3.3 V @ 1 A,
+12 V @ 2 A, -12 V @ 0.05 A,
-5 V @ 0.05 A, +5 Vsb @ 0.1 A
MTBF 114,000 hours @ 25° C 100,000 hours @ 25° C
Safety CE/UL/TUV/CB/CCC CE/UL/TUV/CB/CCC
Table 1.2: Environment specifications
Environment Operating Non-operating
Temperature 0 to 40° C (32 to 104° F) -20 to 60° C (-4 to 140° F)
Humidity 10 to 85% @ 40° C
non-condensing
10 to 95% @ 40° C
non-condensing
Vibration
(5 ~ 500Hz) 0.5G rms 2 G
Altitude 0 to 3,048 m (0 ~ 10,000 ft)
Safety CE compliant

ACP-1320BP User Manual 4
1.5 Dimensions of ACP-1320BP
Figure 1.1 Dimensions of ACP-1320BP

Chapter 2
2System Setup

ACP-1320BP User Manual 6
2.1 Introduction
The following procedures are provided to assist you in installing a backplane, CPU
card, drives, and add-in cards into ACP-1320BP chassis. Please also refer to the
Appendix A, Exploded Diagram, for the parts naming in this manual.
2.2 Removing the cover
To remove the cover of the ACP-1320BP, please refer to Figure 2-1. Remove screws;
slide cover back; lift cover up.
Figure 2.1 Removing the cover

7 ACP-1320BP User Manual
Chapter 2 System Setup
2.3 Installing the backplane and the CPU card
ACP-1320BP accepts 3-slot backplane. To install the backplane, refer to figures and
proceed as follows:
1. Fix the backplane to the backplane holder (T-bar) of chassis with screws.
2. Fix the CPU card on the backplane and card guide with screws.
3. Fix the backplane holder (include CPU card and backplane) on the SATA BP
bracket and card guide on the chassis simultaneously with screws.
4. Plug in the 20/24-pin ATX power connector and +12 V power connector from the
power supply, also the 9-pin USB connectors from the front panel of the chassis.
5. Connect the POWER SW, RESET SW, LAN LED from chassis to the backplane
and HDD LED cables from the alarm board to the backplane.
Figure 2.2 Installing a backplane, CPU card and add-on card
Note! To ensure the best air flow inside the chassis, choosing a CPU cooler
which is lower than 22 mm is highly recommended.

ACP-1320BP User Manual 8
2.4 Installing add-on cards
ACP-1320BP can accept one PCI/PCIe add-on card on the backplane. To install an
add-on card, also refer to Figure 2.2 and proceed as follows:
1. Plug in the add-on card until the card’s gold fingers have been inserted in an
PCI/PCIe slot of the backplane completely.
2. Make sure that the card bracket has been inserted properly and the other edge
of the card has been fixed in the guiding rail.
3. Fasten the card at the top of the bracket with a screw.
2.5 Adding disk drives
ACP-1320BP comes with two easy-to-maintain SATA HDD trays; it also accepts one
slim type optical disk drive and one 3.5” HDD/FDD. To install any of these disk drives,
refer to Figures 2.3 ~ 2.6 and proceed as follows:
2.5.1 Installing a SATA HDD in the SATA HDD tray
ACP-1320BP accepts both SATA and SATA II HDD. It is not necessary to remove
ACP-1320BP’s cover when installing a SATA HDD in any of the SATA HDD trays.
Figure 2.3 Removing the front bezel of the drive bay