Advantech MIO-2375 Installation and operation manual

MIO-2375 Startup Manual 1
Before card installation, check that the following items are
included in your shipment:
1. 1 x MIO-2375 single-board computer
2. 1 x Startup manual p/n: 2046237500
3. 1 x SATA cable p/n: 1700006291
4. 1 x Audio cable p/n: 1700019584-01
5. 2 x COM cable p/n: 1700030404-01
6. 1 x SATA power cable p/n: 1700027546-01
7. 1 x USB cable p/n: 1700030406-01
8. 1 x AT power cable p/n: 1700019705-01
9. 1 x Cooler (heatsink) p/n: 1970004956T001
10. 1 x Screw kit (4 x stando󰀨s) p/n: 1930000058
11. 1 x DeviceOn package
If any of the above items are missing or damaged, contact
your distributor or sales representative immediately.
Note 1: For more information regarding MIO-2375, refer
to the Advantech website for further information.
Note 2: Acrobat Reader is required to view any PDF
le. Acrobat Reader can be downloaded at:
http://get.adobe.com/reader/ (Acrobat is a trade-
mark of Adobe)
MIO-2375 2.5” Pico-ITX SBC with 11th Gen. Intel®
Core™ U-Series (i7/i5/i3/Celeron®) CPU, LPDDR4x
Memory, DP, eDP, 2GbE, M.2 E-Key, M.2 B-Key/M-
Key, iManager 3.0, and Edge AI Software Suite
Startup Manual
General
• CPU:
- Intel® i7-1185G7E/1185GRE quad-core, base frequency
1.8 GHz, max. turbo frequency 4.4 GHz
- Intel® i5-1145G7E quad-core, base frequency 1.5 GHz;
max. turbo frequency 4.1 GHz
- Intel® i3-1115G4E dual-core, base frequency 2.2 GHz;
max. turbo frequency 3.9 GHz
• System Memory: Dual-channel, onboard LDDR4x @
4267 MHz, up to 32 GB
• Cache:
- Intel® i7-1185G7E/1185GRE: 12 MB
- Intel® i5-1145G7E: 8 MB
- Intel® i3-1115G4E: 6 MB
• BIOS: AMI uEFI 256 Mbit
• Watchdog Timer: 255 timer intervals, programmable via
software; multi-level WDT (congured via iManager)
• Battery: Lithium 3 V/210 mAH
• Audio: High denition (HD) audio, Line-In, Line-Out,
Mic-In
Expansion Interface
• 1 x M.2 B-Key 2242/3042 (M-Key available upon request)
• 1 x M.2 E-Key 2230
Display
• Controller: Intel® Iris® Xe Graphics
• Maximum Resolution:
- Display Port: DP 1.4 (DP++),
up to 4096 x 2304 x 36 bpp @ 60 Hz;
with DSC 7680 x 4320 x 30 bpp @ 60 Hz
- Embedded DisplayPort: eDP 1.4 HBR3, up to
4096 x 2304 x 36 bpp @ 60 Hz;
with DSC 7680 x 4320 x 30 bpp @ 60 Hz
- *Optional MIPI-DSI: MIPI-DSI 2.5 GHz, up to
3200 x 2000 x 24 bpp @ 60 Hz;
with DSC 5120 x 3200 x 24 bpp @ 60 Hz
- Dual Display: DP + eDP/MIPI-DSI
Ethernet Interface
• Speed: 10/100/1000 Mbps
• Controller: GbE1 - Intel i219, GbE2 - Intel i210-AT
Mechanical and Environmental
• Dimensions: 100 x 72 mm/3.9 x 2.8 in
• Power Supply Type: Supports ACPI
• Power Requirements: +12 V ± 10% (supports 2-pin AT
power connector and DC jack as a default)
• Operating Temperature:
0 ~ 60 °C/32 ~ 140 °F
Extended: -40 ~ 85 °C/-40 ~ 185 °F
• Weight: 0.26 kg/0.57 lb
Specications
Packing List
For more information about this and other Advantech
products, visit our website at
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and customer service, visit our
support website at
http://support.advantech.com
This manual is for the MIO-2375 series.
Part No. 2046237500
Printed in China
Edition 1
August 2021

2 MIO-2375 Startup Manual
The board features several jumpers that allow the system to be
congured according to the application. The function of each
jumper and connector is listed below.
Jumpers
Label Function
SW1 Automatic Power On Setting
VDD1 LCD Power Setting
Connectors
Label Function
CN1 Front panel
CN2 GPIO
CN3 I2C
CN4 FAN
CN5 DC power in
Battery1 RTC battery
EDP1 eDP
BL1 Inverter power output
DP1 DP++
USB1 USB2.0+3.2
USB3 Internal USB
M2_1 M.2 E-key
M2_2 M.2 B/M-key
SIM1 Nano SIM
LAN1 RJ45_2x1_W/XFMR&LED
SATA1 SATA_7V
Audio1 Audio
COM1 COM1
COM2 COM2
Jumpers and Connectors (Cont.)
Jumper Settings
SW1
Automatic Power On Setting
Setting Function
(1-8) on
AT mode (default)
(1-8) o󰀨 ATX mode
(3-6) on Clear CMOS
(3-6) o󰀨 Normal (retain CMOS)
(2-7) (4-5) Test only
Load BIOS Defaults
Step 1: Power o󰀨 the device
Step 2: Move the DIP switch from Position 3 to 6, then
power on the device
Step 3: Access the BIOS and load default settings (do not
clear time or clear CMOS)
Pop out to remind users to shut the device down
and move the DIP switch from Position 6 to 3.
Step 4: Restart the device
Clear CMOS
Remove the battery (battery 1)
The system will stop for 3 seconds, show checksum errors,
and clear time settings.
VDD1 LCD Power
Setting Function
(1-3) +3.3V (default)
(3-5) +5V
(3-4) +12V
Caution! The computer is provided with a battery-powered
real-time clock circuit. Batteries are at risk of ex-
ploding if incorrectly replaced. Replace only with
same or equivalent type as recommended by the
manufacturer. Discard used batteries according
to manufacturer’s instructions.
Jumpers and Connectors

MIO-2375 Startup Manual 3
Connector Locations
Figure 1. Connector Locations (Top)
Figure 2. Connector Locations (Underside)
Figure 3. Connector Locations (Coastline)
DC IN
RJ45 USB3.2
DP
M.2 B-Key
(co-lay M-Key)
M.2 E-Key
RTC Ba�ery
SATA
USB 2.0
Audio
COM1
Inverter &
SATA Power
GPIO
SIM Card
I2C/SMBus
COM2
LPDDR4x
eD
P conn.
(*
op�onal)
Smart Fan

4 MIO-2375 Startup Manual
Figure 4. Mechanical Drawing (Top View)
Figure 5. Mechanical Drawing (Underside View)
Figure 6. Mechanical Drawing (Side View)
Provisional
Max.Hsu #9374
Ver.1 2021/2/4
0
3.25
50
96.75
100
0
3.25
36
68.75
72
0
1.60
17.94
3.88
0
13.45 30.15 48.87 62.84 82.51
100
MIO-2375 (Coast Line)
0
3.25
18
78.03 96.75
100
0
3.25
25.21
25.72
68.75
72
MIO-2375 (TOP side)
MIO-2375 (Bottom side)
8
7
5
46
A
B
C
3
2
1
A
C
B
D
E
7
5
4
3
2
1
D
E
8
7
5
46
3
2
1
A
C
B
8
7
5
46
3
2
1
D
E
ZONE MARK DESCRIPTION DATE SIGN
V
ABC
APPEARANCE
PART
INTERIOR
PART
FILE NAME
P/N ADDED CODE
MODEL NAME
/
0.20
None
D
0.20
P1
0.05
2021/2/4
2021/2/4
REV.
SIZE UNITS
mm
SHEET
2 Of 3
A3
APPROVED
DESIGNER
CHECKED
DRAWER
SCALE
PART NO.
D
THIRD ANGLE
PROJECTION
0.25
0.30
0.40
0.60
D=3L/1000
0.50
0.20
FINISHING
MATERIAL
(Max)
1:1
S2S1
M2
0.10
0.40
L
0.70
0.40
0.15
0.25
0.20
0.30
0.25
0.50
0.80
1.0
0.50 0.35 0.60
1.10
0.25
0.30
0.45
0.20
0.10 0.15
M1
DIMENSIONAL
TOLERANCES ±
0.10
0.15
0.15
0.30
0.20
ANGLE
6~29.99
30~79.99
80~179.99
180~314.99
315~800
0.05 0~5.99
90
Other 1.5
0.60
1.00
P2
0.15
0.10
0.40
0.50
DESCRIPTION/PART NAME
manual PCB for MIO-2375
2021/2/4
TOLERANCES
PCB T=1.6mm
Max.Hsu
V
Max.Hsu
Kevin.Lin
/
/
Confidential
/
/
/
/
/
/
/
/
ITEM PART NO. DESCRIPTION Q'ty REMARK
Provisional
Max.Hsu #9374
Ver.1 2021/2/4
0
3.25
50
96.75
100
0
3.25
36
68.75
72
0
1.60
17.94
3.88
0
13.45 30.15 48.87 62.84 82.51
100
MIO-2375 (Coast Line)
0
3.25
18
78.03 96.75
100
0
3.25
25.21
25.72
68.75
72
MIO-2375 (TOP side)
MIO-2375 (Bottom side)
8
7
5
46
A
B
C
3
2
1
A
C
B
D
E
7
5
4
3
2
1
D
E
8
7
5
46
3
2
1
A
C
B
8
7
5
46
3
2
1
D
E
ZONE MARK DESCRIPTION DATE SIGN
V
ABC
APPEARANCE
PART
INTERIOR
PART
FILE NAME
P/N ADDED CODE
MODEL NAME
/
0.20
None
D
0.20
P1
0.05
2021/2/4
2021/2/4
REV.
SIZE UNITS
mm
SHEET
2 Of 3
A3
APPROVED
DESIGNER
CHECKED
DRAWER
SCALE
PART NO.
D
THIRD ANGLE
PROJECTION
0.25
0.30
0.40
0.60
D=3L/1000
0.50
0.20
FINISHING
MATERIAL
(Max)
1:1
S2S1
M2
0.10
0.40
L
0.70
0.40
0.15
0.25
0.20
0.30
0.25
0.50
0.80
1.0
0.50 0.35 0.60
1.10
0.25
0.30
0.45
0.20
0.10 0.15
M1
DIMENSIONAL
TOLERANCES ±
0.10
0.15
0.15
0.30
0.20
ANGLE
6~29.99
30~79.99
80~179.99
180~314.99
315~800
0.05 0~5.99
90
Other 1.5
0.60
1.00
P2
0.15
0.10
0.40
0.50
DESCRIPTION/PART NAME
manual PCB for MIO-2375
2021/2/4
TOLERANCES
PCB T=1.6mm
Max.Hsu
V
Max.Hsu
Kevin.Lin
/
/
Confidential
/
/
/
/
/
/
/
/
ITEM PART NO. DESCRIPTION Q'ty REMARK
Provisional
Max.Hsu #9374
Ver.1 2021/2/4
0
3.25
50
96.75
100
0
3.25
36
68.75
72
0
1.60
17.94
3.88
0
13.45 30.15 48.87 62.84 82.51
100
MIO-2375 (Coast Line)
0
3.25
18
78.03 96.75
100
0
3.25
25.21
25.72
68.75
72
MIO-2375 (TOP side) MIO-2375 (Bottom side)
8
7
5
46
A
B
C
3
2
1
A
C
B
D
E
7
5
4
3
2
1
D
E
8
7
5
46
3
2
1
A
C
B
8
7
5
46
3
2
1
D
E
ZONE MARK DESCRIPTION DATE SIGN
V
ABC
APPEARANCE
PART
INTERIOR
PART
FILE NAME
P/N ADDED CODE
MODEL NAME
/
0.20
None
D
0.20
P1
0.05
2021/2/4
2021/2/4
REV.
SIZE UNITS
mm
SHEET
2 Of 3
A3
APPROVED
DESIGNER
CHECKED
DRAWER
SCALE
PART NO.
D
THIRD ANGLE
PROJECTION
0.25
0.30
0.40
0.60
D=3L/1000
0.50
0.20
FINISHING
MATERIAL
(Max)
1:1
S2S1
M2
0.10
0.40
L
0.70
0.40
0.15
0.25
0.20
0.30
0.25
0.50
0.80
1.0
0.50 0.35 0.60
1.10
0.25
0.30
0.45
0.20
0.10 0.15
M1
DIMENSIONAL
TOLERANCES ±
0.10
0.15
0.15
0.30
0.20
ANGLE
6~29.99
30~79.99
80~179.99
180~314.99
315~800
0.05 0~5.99
90
Other 1.5
0.60
1.00
P2
0.15
0.10
0.40
0.50
DESCRIPTION/PART NAME
manual PCB for MIO-2375
2021/2/4
TOLERANCES
PCB T=1.6mm
Max.Hsu
V
Max.Hsu
Kevin.Lin
/
/
Confidential
/
/
/
/
/
/
/
/
ITEM PART NO. DESCRIPTION Q'ty REMARK
Mechanical Drawings

MIO-2375 Startup Manual 5
Figure 7. Mechanical Diagram (with Cooler)
Figure 8. Mechanical Diagram (with Heat Spreader)
0
1.60
17.94
20
Remove release paper
Remove release paper
Remove release paper
0
1.6
17.94
11
20.60
Mechanical Drawings

6 MIO-2375 Startup Manual
Quick Installation Guide
Retreive the cooler/heatspreader from the accessory box. Remove the release paper from the thermal pads.
Retreive the 4 x stando󰀨s from the accessory box. Install the cooler/heatspreader according to the illustrations provided below.
0
1.60
17.94
20
Remove release paper
Remove release paper
Remove release paper
0
1.6
17.94
11
20.60
0
1.60
17.94
20
Remove release paper
Remove release paper
Remove release paper
0
1.6
17.94
11
20.60