Advantech AIMB-706 Installation and operation manual

AIMB-706 Startup Manual 1
AIMB-706 LGA1151 Intel® Core™ i7/i5/i3 ATX with
Dual Display, SATA 3.0, USB 3.1, DDR4
Startup Manual
Specications (Cont.)
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our sup-
port website for AIMB-706 at:
http://advt.ch/aimb706spt
Register your products on our website and get 2 months
extra warranty for free at:
http://www.register.advantech.com
This manual is for the AIMB-706 series Rev. A1.
Part No. 2001070612
Printed in China
3rd Edition
February 2023
• Chipset: Intel® H310 PCH
• System memory: Up to 32 GB in two 288-pin DIMM
sockets, supporting dual-channel DDR4 2400/2666
SDRAM. AIMB-706 supports non-ECC unbu󰀨ered DIMMs
and does not support any memory conguration that
mixes non-ECC with ECC unbu󰀨ered DIMMs.
Note: Due to the inherent limitations of the PC architec-
ture, the system may not fully detect 32 GB RAM
when 32 GB RAM is installed.
• SATA interface: Four onboard Serial ATA 3.0 connectors
support data transmission rates of up to 600 MB/s. All
four SATA 3.0 ports support Advanced Host Controller
Interface (AHCI) technology.
• PCIe and PCI slots: 1 PCIe x16 expansion slot, 1 PCIe
x4 expansion slot, 5 PCI slots 32-bit / 33 MHz PCI 2.2
compliant
• LPC interface: Advantech-designed LPC connector sup-
ports dTPM 2.0 module and COM port extension module.
• Serial ports: Up to six serial ports: COMD1, COMD2 and
COM4 ~ 6 are RS-232; COM3 is RS-232/422/485 with
jumper and BIOS menu options.
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse.
• Watchdog timer: 255 sec timer intervals.
• USB 3.1/2.0: 4 USB 3.1 Gen 1 ports (2 rear, 2 via
header), 5 USB 2.0 ports (2 rear, 2 via header, 1 internal
Type-A)
Graphics Interface
• Chipset: CPU integrated graphics controller
• Display memory: 1 GB maximum shared memory with 2
GB and above system memory installed
• DVI-D: Resolution up to 1920 x 1200 @ 60 Hz refresh
rate
• VGA: Resolution up to 1920 x 1200 @ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:
Intel® I219-V; LAN2 (G2 SKU only):
Intel®
I210-AT
Mechanical and Environmental
• Dimensions (L x W): 304.8 x 244 mm (12” x 9.6”)
• Power supply voltage: +3.3 V, ±5 V, ±12 V, +5 Vsb
• Power consumption:
Intel® Core™ i7-8700 3.2 GHz; DDR4 16GB x 2
Maximum: +3.3 V at 2.74 A, +5 V at 3.5 A, +12 V at 5.92
A, +5 Vsb at 0.05 A, -5 V at 0.01 A, -12 V at 0.08 A
• Operating temperature: 0 ~ 60 °C (depending on CPU)
• Weight of board: 0.7 kg (1.54 lb)
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x AIMB-706 motherboard
• 1 x AIMB-706 Startup Manual
• 2 x Serial ATA HDD data cables
• 1 x Serial ATA HDD power cable
• 1 x I/O port bracket
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
le. Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
Standard Functions
• CPU: LGA1151 socket supporting 8th/9th Gen Intel®
Core™ i7/i5/i3 and Pentium®/Celeron® processors
Note: BIOS version V2.XX can support both 8th and
9th Gen processors while BIOS version V1.XX
can only support 8th Gen processors.
• BIOS: AMI 128 Mbit SPI BIOS.
Specications

2 AIMB-706 Startup Manual
The board has a number of jumpers that allow you to con-
gure your system to suit your application. The table below
lists the function of each jumper and connector.
Connector/Jumper List
Label Function
LAN1 LAN1
LAN2 LAN2 (G2 SKU only)
USB3C1 USB 3.1 Gen 1 port 1, 2
USB3H1 USB 3.1 Gen 1 port 1, 2 (20-pin
header)
USB2C1 USB 2.0 port 1, 2
USB2A1 USB 2.0 port (internal Type-A)
USB2H1 USB 2.0 port 1, 2 (10-pin header)
VGA1+DVI1 VGA connector / DVI-D connector
(DVI1 for G2 SKU only)
COMD1+COMD2 Serial port: RS-232 (DB-9 con-
nector)
COM4 ~ COM6 Serial port: RS-232 (9-pin header,
G2 SKU only)
COM3 Serial port: RS-232/422/485 (9-pin
header, G2 SKU only)
KBMS1 PS/2 keyboard and mouse con-
nector
KBMS2 External keyboard and mouse con-
nector (6-pin header)
CPUFAN1 CPU fan connector (4-pin)
SYSFAN1 ~
SYSFAN3
System fan connector (4-pin)
JFP3 Keyboard lock and power LED
Suspend: fast ash (ATX/AT)
System on: ON (ATX/AT)
System o󰀨: OFF (AT/ATX)
JFP2 External speaker / HDD LED con-
nector / SMBus connector
JFP1 Power switch / reset connector
AUDIO1+AUDIO2 Audio connector (Line-Out, Mic-In)
VOLT1 Alarm board power connector
JCASE1 Case open connector
LANLED1 Front panel LAN indicator connector
SATA0 ~ SATA3 Serial ATA 3.0 port
PCI1 PCI slot
PCI2 PCI slot
PCI3 PCI slot
PCI4 PCI slot
PCI5 PCI slot
PCIE1 PCIe x16 slot
PCIE2 PCIe x4 slot
DIMMA1 Channel A DIMM1
DIMMB1 Channel B DIMM1
ATX12V1 ATX 12 V auxiliary power connector
(for CPU)
EATXPWR1 ATX 24-pin main power connector
(for system)
SPI_CN1 Update BIOS pin header
SPDIF_OUT1 SPDIF audio out pin header
GPIO1 8-bit GPIO from super I/O
SMBUS1 SMBus connector from PCH
FPAUD1 Front panel audio connector
LPC1 Low pin count connector for
Advantech dTPM 2.0 and RS232
modules.
JCMOS1 Clear CMOS
JME1 Intel® ME update
JWDT1 Watchdog timer reset
JOBS1 Hardware monitor alarm
PSON1 AT/ATX mode selection
JUSB_1 USB power source switch between
+5 V and +5 V_ DUAL for rear
USB ports
JUSB_2 USB power source switch between
+5 V and +5 V_ DUAL for onboard
USB ports
JSETCOM3 COM3 RS-232/422/485 jumper
setting
JT1, JR1 COM3 RS-422/485 termination
resistor
JFV1 VGA dummy load setting
JCMOS1: Clear CMOS
JME1: Intel® ME Update
Closed Pins Result
1-2 *Keep CMOS data
*Enable ME update
2-3
Clear CMOS data
Disable ME update
* Default
*Keep CMOS data Clear CMOS data
*Enable ME update Disable ME update
1 2 3
1 2 3
Jumpers and Connectors Jumpers and Connectors (Cont.)

AIMB-706 Startup Manual 3
JWDT1+JOBS1: Watchdog Timer Output and OBS Alarm
Closed Pins Result
2-4, 8-10 Watchdog timer disable (2-4)
OBS beep (8-10)
4-6, 8-10 *Watchdog timer reset (4-6)
OBS beep (8-10)
* Default
Watchdog timer disable (2-4) *Watchdog timer reset (4-6)
OBS beep (8-10) OBS beep (8-10)
PSON1: ATX/AT Mode Selection
Closed Pins Result
1-2 AT mode
2-3 *ATX mode
* Default
1 2 3
AT mode *ATX mode
JUSB_1 (Rear USB), JUSB_2 (Onboard USB): USB
Power Source Switch Between +5V and +5V_DUAL
Closed Pins Result
1-2 *USB +5V_DUAL power
2-3 USB +5V power
* Default
1 2 3
*USB +5 V_DUAL power USB +5 V power
1 2 3
1 2 3
JSETCOM3: COM3 RS-232/422/485 Jumper Settings
Closed Pins Result
5-6, 7-9, 8-10,
13-15, 14-16
*RS-232
3-4, 9-11,
10-12, 15-17,
16-18
RS-422
1-2, 9-11,
10-12, 15-17,
16-18
RS-485
* Default
Note: While RS-485 is selected, it is necessary to
change device mode to RS-485 for further
choice of auto ow control under BIOS menu.
Please refer to Chapter 3.2.2.10 of the user
manual for additional settings.
JFV1: VGA Dummy Load Setting
Closed Pins Result
1-2 Enable VGA dummy load
2-3 *Disable VGA dummy load
* Default
Disable termination *Enable termination
1 2 3
1 2 3
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

4 AIMB-706 Startup Manual
JT1(TX Signal), JR1(RX Signal): COM3 RS-422/485
Termination Resistor
Closed Pins Result
1-2 Disable termination
2-3 *Enable termination
* Default
Enable VGA dummy load *Disable VGA dummy load
Note: It is recommended to leave this function disabled
if you use DVI/DP as your main display.
1 2 3
1 2 3
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of
explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Discard
used batteries according to the manufacturer’s
instructions.
Jumpers and Connectors (Cont.) Declaration of Conformity
Board Layout
JSETCOM3
SATA0 SATA1 SATA2
SATA3
DIMMB1
DIMMA1
PCI2
PCI4
PCIE1
Intel H310 PCH
Intel LGA1151
Core i7/i5/i3
USB2A1
USB3H1
COM3
USB2H1
AUDIO1+AUDIO2
LAN2
USB2C1
LAN1
USB3C1
KBMS1
VGA1
DVI1
COMD1
COMD2
SYSFAN1
SYSFAN3
VOLT1 EATXPWR1 PSON1
SPI_CN1 GPIO1 SMBUS1
JCASE1
COM4
COM5
COM6
LPC1
JT1, JR1
JWDT1+JOBS1
JFP3
JFP1+JFP2
CPUFAN1
JUSB_2
JCMOS1
JME1
PCI5
PCIE2
PCI3
PCI1
SPDIF_OUT1 FPAUD1
LANLED1
SYSFAN2
ATX12V1
JUSB_1
KBMS2
JFV1
3 6 9 12
25811
PWRSW RESET
HDDLED
SNMP
JFP1
&
2 5 8 11
1 4 7 10
HDDLED
SM_BUS
SPEAKER
JFP2
&
PWRLED & KEYLOCK
12345
JFP3
Figure 1: Board Layout: Jumper and Connector Locations