Advantech MIO-5375 Installation and operation manual

MIO-5375 Startup Manual 1
Before you begin installing your board, please make sure
that the following items have been shipped:
• 1 x MIO-5375 SBC
• 1 x SATA cable 30cm (P/N: 1700006291)
• 1 x SATA power cable 35cm (P/N: 1700031583-01)
• 1 x USB2.0 cable 20cm (P/N: 1700030406-01)
• 1 x Audio cable 20cm (P/N: 1700019584-01)
• 2 x COM RS-232/422/485 cable 20cm (P/N: 1700030404-
01)
• 2 x COM RS-232 cable 20cm (P/N: 1700031582-01)
• 1 x Cooler (heatsink) (P/N:1970004884T001/
1970004794T001)
• 1 x Startup manual (P/N: 2046537500)
• 1 x Mini jumper (10pcs package)
• 1 x Screw kit (2 x sets screws and post for M.2 device & 4
setsofscrewsandstand-o󰀨)
• 1 x DeviceOn package
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
General
• CPU:
- Intel®Core™ i7-1185G7E (Quad-Core, 4.40 GHz)
- Intel®Core™ i5-1145G7E (Quad-Core, 4.10 GHz)
- Intel®Core™ i3-1115G4E (Quad-Core, 3.90 GHz)
• Systemmemory: Dual Channel/SODIMM DDR4-3200
MT/s, up to 64 GB
• BIOS: AMI EFI 256Mbit
• Watchdogtimer:65536 level, 0~65535 sec
MIO-5375 3.5” MI/O-Compact SBC, 11th Gen.
Intel®Core™ U-series (i7/i5/i3/Celeron®)
Startup Manual
• TPM2.0
• iManager3.0:Yes
• Expansioninterface:
- M.2:
1 x E-Key 2230 (PCIe x1, USB2.0)
1 x B-Key 3042 (USB2.0) w/Nano-SIM
1 x M-Key 2280 (PCIe x4 Gen.4 for PCIe SSD), optional
SATA
- MI/O Extension connector: 4 x PCIe x1, 1 x PCIe x4,
1 x USB 2.0, LPC, SMBus, Line-out, and 12V/5V Power
supply
• Battery:Lithium 3 V/210 mAH
• Audio:SupportsHighDenitionAudio(HD),line-in,line-
out, and Mic-in
Display
• Controller:
- Intel®SoC integrated for HDMI/DP/Type-C display output
- 48-bit LVDS display output
• Maximumresolution:
- LCD:
LVDS dual channel 48-bit up to 1920x1200
Optional: eDP 1.4 up to 4096x2304@60 Hz
- HDMI/DP:
1 x Port HDMI 2.0 up to 4096x2160@60 Hz
1 x Port DP 1.4a up to 4096x2160@60 Hz
- USB Type-C:
1 x USB3.2 Gen. 2x2 20 Gbps, supports DP1.4a via alt.
mode
• Multipledisplay:Four simultaneous displays via 48-bit
LVDS/eDP+HDMI+DP+Type-C
EthernetInterface
• Speed:10/100/1000 Mbps
• Controller:GbE1 - Intel i219, GbE2 - Intel i210-AT
• Connector:RJ45 x 2
I/O
• InternalI/O:1 x SATA 6 Gb/s, 2 x USB 2.0, 2 x
RS232/422/485, 8-bit GPIO, Inverter, SMBus, CANBus
I2C*, HD audio, LVDS, and system fan.
• RearI/O: 4 x USB 3.2, HDMI, DP, USB type-C, 2 x RJ-45,
1 x DC-Jack (*optional).
• MI/Oexpansion:4 x PCIex1, 1 x PCIe x4, USB 2.0, LPC,
SMBus, line-out, and 12 V/5 V power supply.
• Powerconnectortype:Default support 2 x 2 pin ATX
power connector, DC jack is supported upon by request.
MechanicalandEnvironmental
• Dimensions(LxW): 146 x 102 mm (5.7 x 4 in)
• Powersupplytype:ACPI support for ATX only
• Powerrequirements: Vin: 12 V-24 V +/- 5%
Specications(Cont.)PackingList
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/
This manual is for MIO-5375.
Part No. 2046537500
Printed in China
1st Edition
June 2021
Specications

2 MIO-5375 Startup Manual
• Powerconsumption:
- Max: i7-1185G7E: 43.31 W (12 V)/46.78W (24 V)
- Typical: Idle mode in Windows 10.
i7-1185G7E: 16.56W (12 V)/19.2W (24 V)
• Operatingtemperature: 0 ~ 60 °C (32 ~ 140 °F)
• Weight:0.67 kg/1.47 lb (reference weight of total package)
The board has a number of connectors and jumpers that
allowyoutocongureyoursystemtosuityourapplication.
The table below lists the function of each of the jumpers and
connectors.
Jumpers
Label Function
J3 AT mode /Load BIOS default
VDD1 LCD Power
Connector
Label Function
CN11 Power Input
DIMM1 SO-DIMM 9.2mm
DIMM2 SO-DIMM 5.2mm
Battery1 RTC Battery
CN4 CAN BUS
CN5 Front Panel
AUDIO1 Audio
CN8 I2C
COM1 COM1
COM2 COM2
COM3 COM3
COM4 COM4
CN7 GPIO
LAN1 RJ45_2x1_W/XFMR&LED
BL1 Inverter Power output
LVDS1 48 bit LVDS
EDP1 eDP/MIPI DSI
HDMI1 HDMI
DP1 DP
TYPEC1 TYPEC
M2_1 M.2 E-key
M2_2 M.2 M-key
M2_3 M.2 B-key
SIM NANO SIM
J3:ATmode/LoadBIOSdefault
Function JumperSetting
Auto Power On
(1-2)
Reserve
(3-4)
Short: Load BIOS default
Open: Normal
(5-6)
Toloadfactorydefaults,dothis:
Step1:Powero󰀨
Step 2 : Remove the Jumper (3-4) and add to (5-6), then
power on.
BIOS will load factory defaults (does not clear time or clear
CMOS), a message will remind user to shut down system
and restore Jumper (3-4)
Step 3 : Power on again.
If you want to Clear CMOS, remove battery (battery 1).
System will pop up a message...wait for 3 seconds. RTC
time will clear but keep the BIOS settings.
VDD1:LCDPower
Function JumperSetting
+3.3V
(1-3)
+5V
(3-5)
+12V
(3-4)
Caution! The computer is provided with a battery-powered
real-time clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
Specications(Cont.)
JumpersandConnectors(Cont.)
JumpersandConnectors

MIO-5375 Startup Manual 3
Figure 1: MIO-5375 Connector Locations (Top Side)
Figure 2: MIO-5375 Connector Locations (Bottom Side)
Figure 3: MIO-5375 Connector Locations (Coastline)
ConnectorsLocations

4 MIO-5375 Startup Manual
1. There is a Cooler/Heatsink in the white box, please take it out and remove the release paper from the thermal pads.
2. There are four screws inside the white box, follow the installation sequence demonstrated below to secure the cooler/
heatsink:
Cooler Heatsink
 QuickInstallationGuide