Advantech PCE-3026 Installation and operation manual

PCE-3026 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. 1 PCE-3026 PICMG 1.3 System Host Board
2. 1 PCE-3026 startup manual P/N: 2006302600
3. 1 CD with utility P/N: 2066302600
4. 1 Serial ATA HDD data cables P/N: 1700003194
5. 1 Serial ATA HDD power cables P/N: 1703150102
6. LPT cable P/N: 1700002223
7. COM cable P/N: 1700008762
8. USB cable P/N: 1700014398
9. Power converter (Connecting
from peripheral power connector
on power supply to PWR1
on board) P/N: 1703040100
10. 1 warranty card P/N: 2190000902
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of PCE-3026, please refer
to information on the enclosed CD-ROM (in PDF
format).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
PCE-3026 LGA1155 Intel®CoreTM i7/i5/i3/ Pentium®/
Celeron®PICMG 1.3 Half Sized System Host Board
with DDR3 / Dual GbE LAN
Startup Manual
General
• LGA1155 Intel®Core™ i7/i5/i3/Pentium®/Celeron®
CPU
Core
i7-3770
Core
i7-2600
Core i5-
3550S
Core
i5-2400
Core
i3-3220
Core
i3-2120
Pentium
G2120
Pentium
G850
Pentium
G540
Base Frequency 3.4 GHz 3.4 GHz 3 GHz 3.1 GHz 3.3 GHz 3.3 GHz 3.1 GHz 2.9 GHz 2.5 GHz
L3 Cache (MB) 8 8 6 6 3 3 3 3 2
• BIOS: AMI 64 Mb SPI flash
• Chipset: Intel®H61
• System memory:
Support dual channel DDR3 1066/1333 4 GB per DIMM
without ECC function; Max. capacity is up to 8 GB
• SATA interface: Supports 3 SATA2.0 without Raid func-
tion.
• Serial ports: 2 RS-232, support 4 RS-422/485 with
optional COM module: PCA-COM485-00A1E
• Parallel port: 1, supports SPP/EPP/ECP mode
• Keyboard/mouse connector: Supports 1 external 6-pin
header
• Watchdog timer: Programmable 1~255 sec/min
• USB (2.0): 8 USB2.0
• GPIO: 1 programmable 8-bit GPIO pin-header
• Operating system: Win 7 (32/64 bit), Win XP SP3 (32/64
bit), Linux (Fedora Core 16, 32/64 bit), QNX 6.5 (32 bit)
VGA/DVI Interface
• Chipset: Intel®HD Graphics
Ethernet Interface
• Chipset supports:
- LAN 1: Intel
®
82579V
- LAN 2: Intel
®
82583V
• Connection: 2 on-board RJ-45 connector with LED
indicators
Mechanical and Enviromental
• Dimensions: (L x W): 167.64 x 126.39 mm
• Power supply voltage: +3.3 V, +5 V, +12 V, 5VSB
• Power requirements:
CPU: Processor: Intel
®
Core™ i5-2400 (3.1 GHz);
Memory: 2 x DDR3 1333 MHz 4 GB DIMMs
Voltage (V) 3.3 5 12 5VSB
Current (A) 1.54 1.05 3.8 0.24
Power consumption (W) 5.173 5.304 45.866 1.203
• Operating temperature: 0 ~ 60° C (depending on CPU)
• Weight: 0.33 kg (weight of board)
Thermal
• CPU Cooler: Suggested order no: 1960047831N001,
1960053207N001
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/default.
aspx
This manual is for the PCE-3026 Series Rev. A1.
Part No. 2006302600
Printed in China
1st Edition,
October 2012

2 PCE-3026 Startup Manual
Suggested backplane:
P/N PCIex16 PCIex4 PCIex1 PCI AT ATX
PCE-3B06-00A1E 1 4 V V
PCE-3B03-00A1E 1 1 V V
PCE-3B06-03A1E 1 3 V V
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
LPT1 Parallel port, supports SPP/EPP/ECP mode
LAN1 Intel
®
82579V
LAN2 Intel
®
82583V
VGA1 VGA connector
KBMS1 External keyboard/mouse connector
COM12 Box header for RS-232*2
JIR1 Infrared connector
JFP1 Power Switch / Reset connector
JCASE1 Case open
CPUFAN1 CPU FAN connector (4-pin)
LANLED1 LAN1/2 LED connector
HDAUD1 HD audio extension module connector
USB12 USB port 1, 2
USB34 USB port 3, 4
USB56 USB port 5, 6
USB7 USB port 7
USB 8 USB on rear I/O
S ATA 1 Serial ATA1
S ATA 2 Serial ATA2
S ATA 3 Serial ATA3
CPU1 CPU Socket
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
GPIO1 GPIO pin header
LPC1 Low pin count module expansion pin-header
PWR1 12 V, 5 V power connector
DVI1
DVI connector
Jumpers
Label Function
JCMOS1 CMOS clear
JOBS1+JWDT1 Hardware monitor alarm+watchdog
timer output selection
BZ1 Buzzer setting
KL1 Keyboard lock
JCMOS1: Clear CMOS
Closed Pins Result
1-2 Keep CMOS (Default)
2-3 Clear CMOS
JOBS1+JWDT1: Hardware monitor alarm+watchdog
timer output selection
Function Jumper Setting
4-6 Enable watchdog timer (Default)
8-10 Enable Hardware monitor alarm (Default)
Closed Open
KL1: Keyboard lock
Closed Pins Result
Open Disable keyboard lock (Default)
Close Enable keyboard lock
BZ1: Buzzer setting
Closed Pins Result
3-4 Enable buzzer
(Default)
Connect 1 & 4 Connecting to external speaker
Jumpers and Connectors
Jumpers and Connectors
1 2 3 4
Specications Cont.
1
2
3 5 7 9
4 6 8 10

PCE-3026 Startup Manual 3
The drivers for the PCE-3026 are located on the software
installation CD. Please click through the folder and follow
the on screen instructions to install them.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditons:
Software Installation
Declaration of Conformity
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Board Layout
JIR1+JOBS1+JWDT1
COM12
USB8
LAN2
LAN1
LANLED1
VGA1
HDAUD1
DVI1
KBMS1
JCASE1
BZ1
H61
JCMOS1
SATA1
SATA2
SATA3
LPT1
FP1 USB12
USB34
USB7
USB56
CPU
DIMMB1
PWR1
DIMMA1
GPIO1
CPUFAN1
KL1
LPC1
How to Power on PCE-3026
To power on PCE-3026 with PCE-3BXX backplane, please
ensure that the below connectors and jumper are correctly
connected and chosen.