Advantech PCE-5130 User manual

User Manual
PCE-5130
Socket M Intel® CoreTM 2 Duo /
CoreTM Duo / Celeron-M
processor PICMG 1.3 CPU Board
with PCIe / DDR2 / VGA / Dual
GbE LAN

PCE-5130 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2009
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
AWARD BIOS is a trademark of Phoenix Technologies LTD.
IBM and PC are trademarks of International Business Machines Corporation.
Intel, CoreTM 2 Duo, CoreTM Duo, Celeron-M are trademarks of Intel Corporation.
WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are the properties of their respective owners.
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
Part No. 2002513000 Edition 1
Printed in China February 2009

iii PCE-5130 User Manual
Declaration of Conformity
FCC
This device complies with the requirements in part 15 of the FCC rules:
!Operation is subject to the following two conditions:
!This device may not cause harmful interference
!This device must accept any interference received, including interference that
may cause undesired operation
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this device in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense. The
user is advised that any equipment changes or modifications not expressly approved
by the party responsible for compliance would void the compliance to FCC regula-
tions and therefore, the user’s authority to operate the equipment.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.

PCE-5130 User Manual iv
Memory Compatibility
Brand Size Speed Type ECC Vendor
PN Advantech PN Memory
Apacer
512 MB DDR2
533 DDR2 N78.91G66. 420
96D2-
512M533NN-AP
ELPIDA E5108AG-
5C-E (64x8)
512 MB DDR2
667 DDR2 N78.91G92. 420 N/A ELPIDA E5108AG- 6E-E (64x8)
1 GB DDR2
533 DDR2 N78.01066. 400 N/A
SAMSUNG
K4T51083QB-
ZKD5 (128x4)
1 GB DDR2
533 DDR2 N78.01G66. 420
96D2-1G533NN-
AP
ELPIDA
E5108AGBG-6E-E
(64x8)
1 GB DDR2
667 DDR2 N78.01G92. 420 N/A
ELPIDA
E5108AGBG-6E-E
(64x8)
2 GB DDR2
669 DDR2 N78.A1G9O .404 96D2-2G667-AP SEC K4T1G08400 (128x8)
DSL
512 MB DDR2
533 DDR2 N N/A N/A
infineon
HYB18T512
800AF37
FSS43331 (64x8)
1 GB DDR2
533 DDR2 N N/A N/A ELPIDA E5108AE- 5C-E (64x8)
1 GB DDR2
667 DDR2 N N/A N/A
ELPIDA
E5108AGBG-6E-E
(64x8)
2 GB DDR2
667 DDR2 N N/A N/A
ELPIDA
E1108ACSE-6E-
E(128x8)
Kingston 2 GB DDR2
667 DDR2 NKVR667D 2N5/2G N/A Micron 7KE12 D9HNL (128x8)

v PCE-5130 User Manual
Network Feature Comparison
Transcend
256 MB DDR2
533 DDR2 NTS32MLQ 64V5F
SAMSUNG 443
K4T56083QF-
GCD5 (32x8)
256MB DDR2
533 DDR2 NTS32MLQ 64V5M
96D2-
256M533NN-TR
infineon
HYB18T512160AF
3.7 3VV21710
(32x16)
512MB DDR2
533 DDR2 NTS64MLQ 64V5J
96D2-
512M533NN-
TR1
SEC
K4T51083QC
ZCD5 (64X8)
512MB DDR2
667 DDR2 N
TS6QNJ2
2850-6S/
TS64MLQ
64V6J
96D2-
512M667NN-TR
SAMSUNG
K4T51083QC
ZCE6 (64x8)
1GB DDR2
533 DDR2 NTS128ML Q64V5J
96D2-1G533NN-
TR1
SEC
K4T51083QC
ZCD5 (64X8)
1GB DDR2
667 DDR2 NTS2QNJ2 3450-6S
96D2-1G667NN-
TR
SEC
K4T51083QE
ZCE6 (64x8)
1GB DDR2
668 DDR2 N
TS2QNJ2
3450-6S/
TS128ML
Q64V6J
96D2-1G667NN-
TR
SEC
K4T51083QG
HCE6 (64x8)
1GB DDR2
667 DDR2 NN/A N/A SEC K4T51083QC ES
2GB DDR2
669 DDR2 NTS5QNU2 3451-6S 96D2-2G667-TR
SAMSUNG
K4T1G084QD-
ZCE6 (128x8)
2GB DDR2
667 DDR2 NTS256ML Q64V6U N/A Micron 7HE12 D9HNL (128x8)
2GB DDR2
667 DDR2 NTS256ML Q64V6U N/A
SAMSUNG
K4T1G084QA-
ZCE6 (128x8)
LAN/Model PCE-5130G2 PCE-5130VG
LAN1:Intel 82574 Yes Yes
LAN2:Intel 82573 Yes No

PCE-5130 User Manual vi
Product Warranty (2 Years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
If an Advantech product is defective, it will be repaired or replaced at no charge dur-
ing the warranty period. For out-of-warranty repairs, you will be billed according to
the cost of replacement materials, service time and freight. Please consult your
dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, type of
PC, CPU speed, Advantech products used, other hardware and software used,
etc.) Note anything abnormal and list any on-screen messages you get when
the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return material autho-
rization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

vii PCE-5130 User Manual
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the PCE-5130 mechanically and
electrically before shipment. It should be free of marks and scratches and in perfect
working order upon receipt. As you unpack the PCE-5130, check it for signs of ship-
ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or
it fails to meet the specifications, notify our service department or your local sales
representative immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will make arrange-
ments to repair or replace the unit.
!1 PCE-5130 PICMG 1.3 Single Host Board
!1 PCE-5130 startup manual P/N: 2002513010
!1 CD with utility P/N: 2062513000
!1 FDD cable P/N: 1700340640
!1 User note for full-sized CPU card P/N: 2002721020
!2 Serial ATA HDD data cable P/N: 1700003194
!2 Serial ATA HDD power cable P/N: 1703150102
!1 COM + printer ports cable kit P/N: 1701260305
!1 4-port USB cable kit(Only for VG Sku) P/N: 1700008461
!1 2-port USB cable kit (Only for G2) P/N: 1700002204
!1 Keyboard and mouse Y cable P/N: 1700060202
!1 jumper package P/N: 9689000068
!1 warranty card P/N: 2190000902
!1 Ultra ATA 66/100 HDD cable P/N: 1701400452
!1 CPU Cooler P/N: 1750000246

PCE-5130 User Manual viii

ix PCE-5130 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ............................................................................................... 2
1.2 Features & Benefits................................................................................... 2
Table 1.1: Features & Benefits .................................................... 2
1.3 Specifications ............................................................................................ 3
1.3.1 System .......................................................................................... 3
1.3.2 Memory ......................................................................................... 3
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 3
1.3.6 Industrial features ......................................................................... 4
1.3.7 Mechanical and environmental specifications............................... 4
1.4 Jumpers and Connectors .......................................................................... 4
Table 1.2: Jumper list .................................................................. 4
Table 1.3: Connector list.............................................................. 5
1.5 Board Layout: Jumper and Connector Locations...................................... 6
Figure 1.1 Jumper and connector locations................................. 6
1.6 PCE-5130 Block Diagram ......................................................................... 7
Figure 1.2 PCE-5130 block diagram............................................ 7
1.7 Safety Precautions .................................................................................... 8
1.8 Jumper Settings ........................................................................................ 9
1.8.1 How to set jumpers ....................................................................... 9
1.8.2 CMOS clear (CMOS1) .................................................................. 9
Table 1.4: CMOS clear (CMOS1)................................................ 9
1.8.3 Watchdog timer output (JWDT1) ................................................ 11
Table 1.5: Watchdog timer output (JWDT1) .............................. 11
Table 1.6: H/W monitor alarm (JOBS1)..................................... 12
1.8.4 COM2 RS-232/422/485 mode selector (JESTCOM2) ................ 13
Figure 1.3 COM2 RS-232/422/485 jumper setting .................... 13
Table 1.7: COM2 RS-232/422/485 mode selector .................... 13
1.9 System Memory ...................................................................................... 15
1.10 Memory Installation Procedures.............................................................. 15
1.11 Cache Memory........................................................................................ 15
1.12 Processor Installation.............................................................................. 16
Chapter 2 Connecting Peripherals ....................19
2.1 Introduction ............................................................................................. 20
2.2 Floppy Drive Connector (FDD1).............................................................. 20
2.3 Parallel Port (LPT1)................................................................................. 21
2.4 USB Ports (USB12, USB34) ................................................................... 22
2.5 VGA Connector (VGA1) .......................................................................... 23
2.6 Serial Ports (COM1, COM2) ................................................................... 24
2.7 PS/2 Keyboard and Mouse Connector (KBMS1) .................................... 25
2.8 CPU Fan Connector (CPUFAN1)............................................................ 26
2.9 Front Panel Connectors (JFP1, JFP2 & JFP3) ....................................... 27
2.9.1 Power LED and keyboard lock (JFP3)........................................ 28
Table 2.1: PS/2 or ATX power supply LED status..................... 28
2.9.2 External speaker (JFP2) ............................................................. 28
2.9.3 Reset connector (JFP1) .............................................................. 28
2.9.4 HDD LED connector (JFP2)........................................................ 28
2.9.5 ATX soft power switch (JFP1)..................................................... 28
2.10 H/W Monitor Alarm (JOBS1) ................................................................... 29
2.11 LAN Ports (LAN1 & LAN2) ...................................................................... 30

PCE-5130 User Manual x
Table 2.2: LAN LED indicators .................................................. 30
2.12 High Definition Audio Module Interface................................................... 31
2.13 GPIO Header (GPIO1)............................................................................ 32
2.14 Case Open Connector (JCASE1) ........................................................... 33
2.15 Front Panel LAN Indicator Connector (LANLED1).................................. 34
Table 2.3: Front Panel LAN indicator connector ....................... 34
2.16 Serial ATA Interface (SATA1 ~ SATA2).................................................. 36
Chapter 3 Award BIOS Setup ............................ 37
3.1 Introduction ............................................................................................. 38
3.1.1 CMOS RAM Auto-backup and Restore ...................................... 38
3.2 Entering Setup ........................................................................................ 38
Figure 3.1 Award BIOS Setup initial screen .............................. 38
3.3 Standard CMOS Setup ........................................................................... 39
Figure 3.2 Standard CMOS Features Screen ........................... 39
3.4 Advanced BIOS Features ....................................................................... 40
Figure 3.3 Advanced BIOS features screen (1)......................... 40
Figure 3.4 Advanced BIOS features screen (2)......................... 40
3.5 Advanced Chipset Features.................................................................... 42
Figure 3.5 Advanced chipset features screen ........................... 42
3.6 Integrated Peripherals............................................................................. 44
Figure 3.6 Integrated peripherals .............................................. 44
Figure 3.7 On-Chip IDE Device ................................................. 44
Figure 3.8 Onboard Device ....................................................... 45
Figure 3.9 Super I/O Device ...................................................... 46
3.7 Power Management Setup ..................................................................... 48
Figure 3.10Power management setup screen (1) ...................... 48
Figure 3.11Power management setup screen (2) ...................... 48
Table 3.1: Power Saving ........................................................... 49
3.8 PnP/PCI Configurations .......................................................................... 50
Figure 3.12PnP/PCI configurations screen ................................ 50
3.9 PC Health Status .................................................................................... 51
Figure 3.13PC Health Status Screen ......................................... 51
3.10 Frequency / Voltage Control ................................................................... 52
Figure 3.14Spread Spectrum Control screen ............................. 52
3.11 Password Setting .................................................................................... 53
3.12 Save & Exit Setup ................................................................................... 53
3.13 Exit Without Saving................................................................................. 53
Chapter 4 Chipset Software Installation Utility 55
4.1 Before you Begin .................................................................................... 56
4.2 Introduction ............................................................................................. 56
4.3 Windows XP Driver Setup....................................................................... 57
Chapter 5 VGA Setup ......................................... 59
5.1 Introduction ............................................................................................. 60
5.2 Windows XP Driver Setup....................................................................... 60
Chapter 6 LAN Configuration ............................ 63
6.1 Introduction ............................................................................................. 64
6.2 Features.................................................................................................. 64
6.3 Installation............................................................................................... 64
6.4 Win XP Driver Setup ............................................................................... 65

xi PCE-5130 User Manual
Appendix A Programming the Watchdog Timer..67
A.1 Introduction ............................................................................................. 68
A.1.1 Watchdog timer overview............................................................ 68
A.1.2 Programming the watchdog timer ............................................... 68
Table A.1: Watchdog timer registers.......................................... 69
A.1.3 Example program........................................................................ 70
Appendix B I/O Pin Assignments..........................75
B.1 Floppy Drive Connector (FDD1).............................................................. 76
Table B.1: Floppy drive connector (FDD1) ................................ 76
B.2 Parallel Port Connector (LPT1) ............................................................... 77
Table B.2: Parallel port connector (LPT1).................................. 77
B.3 VGA Connector (VGA1) .......................................................................... 77
Table B.3: VGA connector (VGA1) ............................................ 77
B.4 RS-232 Serial Port (COM1) .................................................................... 78
Table B.4: RS-232 serial port (COM1)....................................... 78
B.5 RS 232/422/485 Serial Port (COM2)....................................................... 78
Table B.5: RS-232 / 422 / 485 serial port (COM2)..................... 78
B.6 USB Header (USB12 ~ 34) ..................................................................... 79
Table B.6: USB Header (USB12 ~ 34) ...................................... 79
B.7 PS/2 Keyboard/Mouse Connector (KBMS1) ........................................... 79
Table B.7: PS/2 keyboard/mouse connector (KBMS1).............. 79
B.8 External Keyboard Connector (KBMS2) ................................................. 80
Table B.8: External keyboard connector (KBMS2) .................... 80
B.9 CPU Fan Power Connector (CPUFAN1) ................................................ 80
Table B.9: CPU fan power connector (CPUFAN1) ................... 80
B.10 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY
LOCK) ..................................................................................................... 80
Table B.10:Power LED and keyboard lock connector (JFP3 /
PWR_LED & KEY LOCK)......................................... 80
B.11 External Speaker Connector (JFP2 / SPEAKER) ................................... 81
Table B.11:External speaker connector (JFP2 / SPEAKER) ...... 81
B.12 Reset Connector (JFP1 / RESET) .......................................................... 81
Table B.12:Reset connector (JFP1 / RESET)............................. 81
B.13 HDD LED (JFP2 / HDDLED)................................................................... 81
Table B.13:HDD LED (JFP2 / HDDLED) .................................... 81
B.14 ATX Soft Power Switch (JFP1 / PWR_SW) ............................................ 82
Table B.14:ATX soft power switch (JFP1 / PWR_SW) ............... 82
B.15 Hi-definition Audio Link Connector (HDAUD1) ....................................... 82
Table B.15:Hi-definition audio link connector (HDAUD1) ........... 82
B.16 SM Bus Connector (JFP2 / SNMP)......................................................... 82
Table B.16:SM bus connector (JFP2 / SNMP) ........................... 82
B.17 LAN1 and LAN2 LED Connector (LANLED1) ......................................... 83
Table B.17:LAN1 and LAN2 LED connector (LANLED1) ........... 83
B.18 GPIO Header (GPIO1) ............................................................................ 83
Table B.18:GPIO header (GPIO1) .............................................. 83
B.19 System I/O Ports ..................................................................................... 84
Table B.19:System I/O ports....................................................... 84
B.20 DMA Channel Assignments .................................................................... 85
Table B.20:DMA channel assignments....................................... 85
B.21 Interrupt Assignments ............................................................................. 85
Table B.21:Interrupt assignments ............................................... 85
B.22 1st MB Memory Map ............................................................................... 86
Table B.22:1st MB memory map ................................................ 86
B.23 PCI Bus Map ........................................................................................... 86
Table B.23:PCI bus map............................................................. 86

PCE-5130 User Manual xii
Appendix C Programming the GPIO .................... 87
C.1 Supported GPIO Register ....................................................................... 88
C.1.1 GPIO registers ............................................................................ 88
C.1.2 GPIO example program-1........................................................... 88

Chapter 1
1Hardware
Configuration

PCE-5130 User Manual 2
1.1 Introduction
PCE-5130 is a PICMG 1.3 form-factor single host board which is designed with Intel
945GME, plus ICH7M-DH platform for industrial applications that require mainstream
computing capability and low power consumption.
PCE-5130 supports Intel CoreTM2 Duo, CoreTM Duo and Celeron® M processors
with FSB up to 667 MHz and DDR2 400/533/667 MHz SDRAM up to 4 GB. With
mainstream computing technology and low power consumption, PCE-5130 is suit-
able for industrial applications in high temperature environments or in compact enclo-
sures.
PCE-5130 offers high-performance, cost-saving integrated graphics, a built-in Intel®
945GME chipset, and features the unique Intel® Graphics Media Accelerator 950,
which maximizes graphic performance and shares system memory up to 224 MB.
PCE-5130 also supports an LVDS interface for digital panel connection.
PCE-5130 also has rich I/O interfaces; it has two SATA2 ports for connecting main-
stream hard disks and optical drives, and the two on-board serial ports (COM ports)
can be used for various industrial control applications. With one PCIe x16 and four
PCIe x1 lanes going to the backplane, PCE-5130 can connect to various kinds of
expansion slots such as PCI, PCI-X and PCIe slots with different backplanes.
With outstanding performance and exceptional features, PCE-5130 is an ideal com-
puting platform for up-and-coming industrial applications, both for today and for
tomorrow.
1.2 Features & Benefits
Table 1.1: Features & Benefits
Features Benefits
Supports Intel® CoreTM2 Duo / Core
Duo/Celeron® M Series processors
Supports FSB 533/667 MHz CoreTM2 Duo/CoreTM
Duo/Celeron® M mobile processors with maxi-
mum 34 W thermal design power for applications
that require low power consumption in compact-
size enclosures, such as 1U, 2U chassis
Dual Channel DDR2 400/533/667
DIMMs
Supports DDR2 667MHz up to 4 GB (mainstream
and high availability)
Cost-saving integrated graphics core VGA and LVDS for Dual Display and Digital Panel
applications
Dual Gigabit Ethernet LAN via dedicated
PCI Express x1 Lanes for intense net-
working
Provides high throughput for heavy-load network-
ing applications
Dual COM ports with RS232/422/485 Dual SATA ports for SATA interface HDDs or
ODDs, 2 comports with RS232/422/485 for con-
trolling equipment applications

3 PCE-5130 User Manual
Chapter 1 Hardware Configuration
1.3 Specifications
1.3.1 System
!CPU: Intel Core 2 Duo / Core Duo / Celeron M Sequence Processors with 533/
667 MHz FSB
!L2 Cache: Up to 4 MB depends on CPU, Celeron M or Core Solo/Duo, or
Merom CPU category
!BIOS: Award SPI BIOS (16Mb SPI)
!System Chipset: 945GME GMCH plus ICH7M-DH ICH
!SATA hard disk drive interface: Two onboard SATA connectors with data
transmission rates of up to 150 MB/s. These interfaces can be enabled/disabled
in the BIOS
!Floppy disk drive interface: Supports one floppy disk drive, 5.25" (360 KB and
1.2 MB) or 3.5" (720 KB, 1.44 MB). These interfaces can be enabled/disabled in
the BIOS
1.3.2 Memory
!RAM: Up to 4 GB in two 240-pin DIMM sockets. Supports dual-channel DDR2
400/533 / 667 MHz SDRAM
1.3.3 Input/Output
!PCI express lanes: One PCIe x16 and four PCIe x1 lanes to the backplane
!PCI bus: Four PCI masters to the backplane, 32-bit, 33 MHz PCI 2.2 compliant
!Enhanced parallel port: This EPP/SPP/ECP port can be configured to LPT1. A
standard DB-25 female connector provided
!Serial ports: Two serial ports, one is RS 232 and other one is RS-232 / 422 /
485
!PS/2 keyboard and mouse connector: One 6-pin mini-DIN connectors is
located on the mounting bracket for easy connection to a PS/2 keyboard and
mouse via the Y-cable included in the package
!USB port: Supports up to eight USB 2.0 ports with transmission rate up to 480
Mbps. 3 or 4 ports are on the CPU card and 4 ports are on the backplane
1.3.4 Graphics
!Controller: Intel® 945GME integrated Intel® GMA 950
!Display memory: Dynamically shared system memory up to 224 MB
!CRT: Up to 2048 x 1536 resolution, 400 MHz integrated 24 bit RAMDAC, Dual
independent display options with digital display, Support CRT Hot plug
!PCI express x16 slot on the backplane: An external graphic card can be
installed in the PCIe x16 slot for stronger 2D/3D graphic capability
1.3.5 Ethernet LAN
!Supports single/dual 10/100/1000 Mbps Ethernet port(s) via the dedicated PCI
Express x1 bus which provides 500 MB/s data transmission rate
!Controller:
–LAN 1: Intel 82574 (G2 version or VG version)
–LAN 2: Intel 82573 (G2 Version)

PCE-5130 User Manual 4
1.3.6 Industrial features
!Watchdog timer: Can generate a system reset or IRQ11. The watchdog timer
is programmable, with each unit equal to one second or one minute (255 levels)
1.3.7 Mechanical and environmental specifications
!Operating temperature: 0 ~ 60° C (32 ~ 140° F, Depending on CPU)
!Storage temperature: -20 ~ 70° C (-4 ~ 158° F)
!Humidity: 20 ~ 95% non-condensing
!Power supply voltage: +12 V, +5 V, +3.3 V, +5 VSB
!Power consumption: Maximum:
CPU: Intel Core 2 Duo Processor T7600;
Memory: 2 DDR2 667 MHz 2 GB DIMMs
Voltage +12 V +5 V +3.3 V +5 VSB
Current 2.81 A 0.99 A 2.47 A 0.25 A
!Board size: 338.58 mm (L) x 126.39 mm (W) (13.3" x 4.98")
!Board weight: 0.490 kg
1.4 Jumpers and Connectors
Connectors on the PCE-5130 single host board link it to external devices such as
hard disk drives and a keyboard. In addition, the board has a number of jumpers
used to configure your system for your application.
The tables below list the function of each of the board jumpers and connectors. Later
sections in this chapter give instructions on setting jumpers. Chapter 2 gives instruc-
tions for connecting external devices to your motherboard.
Table 1.2: Jumper list
Label Function
CMOS1 CMOS clear
JWDT1 Watchdog Reset
JOBS1 HW Monitor Alarm
JSETCOM2 COM2 RS-232/422/485 selection

5 PCE-5130 User Manual
Chapter 1 Hardware Configuration
Table 1.3: Connector list
Label Function
IDE1 Primary IDE connector
FDD1 FDD connector
LPT1 Parallel port, Parallel port x 1, supports SPP/EPP/ECP mode
LAN1 GbE LAN1 / Intel 82574
LAN2 GbE LAN2 / Intel 82573
VGA1 VGA connector
KBMS1 PS/2 keyboard and mouse connector
KBMS2 External keyboard/mouse connector
COM1 Serial port: COM1; RS-232 (Box Header)
COM2 Serial port: COM2; RS-232 / 422 / 485
(G2 version: 9-pin Box Header; VG version: 9-pin D-Sub)
JSETCOM2 COM2 RS-232/422/485 mode selection
JIR1 Infrared connector
JFP3
(Keyboard
Lock and
Power LED)
Power
LED
Suspend: Fast flash (ATX/AT)
System On: ON (ATX/AT)
System Off: OFF (AT)
System Off: Slow flash (ATX)
JFP2 External speaker / SATA HDD LED connector
JFP1 Power Switch / Reset connector
JCASE1 Case Open
CPUFAN1 CPU FAN connector (4-pin)
LANLED1 LAN1/2 LED extension connector
HDAUD1 Connector for HD audio extension module
USB12 USB port 1, 2
USB34 USB port 3, 4
SATA1 Serial ATA1
SATA2 Serial ATA2
CPU1 CPU Socket
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
GPIO1 GPIO pin header (SMD pitch-2.0 mm)
VP1 LVDS Panel Back Light Power Connector
LVDS1 LVDS Connector

PCE-5130 User Manual 6
1.5 Board Layout: Jumper and Connector
Locations
Figure 1.1 Jumper and connector locations
JFP1 JFP2 JFP3
DIMMA1
DIMMB1
LVDS1
VP1
JLVDS1
CPUFAN1
SPI_CN1
HDAUD1
CMOS1
JIR1
JWDT1 JOBS1
JSETCOM2
GPIO1 LPC1
BMC1
KBMS2
KBMS1
VGA1
LAN2 LAN1
COM1 for VG Sku
LANLED1
COM2 COM1 for G2 Sku
USB12
USB34 for VG Sku
USB3 for G2 Sku
LPT1
FDD1
IDE1
ISA1 ISA2
JIR1
JCASE1

7 PCE-5130 User Manual
Chapter 1 Hardware Configuration
1.6 PCE-5130 Block Diagram
Figure 1.2 PCE-5130 block diagram

PCE-5130 User Manual 8
1.7 Safety Precautions
Warning! Always completely disconnect the power cord from your chassis when-
ever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sud-
den power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to static
electricity discharges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
Caution! The computer is provided with a battery-powered real-time clock. There
is a danger of explosion if battery is incorrectly replaced. Replace only
with same or equivalent type recommended by the manufacturer. Dis-
card used batteries according to manufacturer’s instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.