Advantech PCE-7131 Installation and operation manual

PCE-7131/5131/5031 Startup Manual 1
Packing List
Before you begin installing your card, please make sure that
the following items have been shipped:
1. PCE-7131/5131/5031 PICMG 1.3 Single Host Board
2. PCE-7131/5131/5031 Startup Manual
3. Serial ATA HDD data cables
4. Serial ATA HDD power cables
5. COM port cable kit
6. 2-port USB cable kit
7. Keyboard and mouse Y cable
8. Jumper package
9. Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of PCE-7131/5131/5031,
please refer to user manual on the Advantech
Website.
Note 2: Acrobat Reader is required to view any PDF
le. Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
PCE-7131/5131/5031 LGA1151 Intel®CoreTM i7/i5/i3/
Pentium®ECC/non-ECC (PCE-7131) PICMG 1.3 Single
Host Board with (ECC/non-ECC) DDR4/M.2 (2280)/
Dual GbE LAN Startup Manual
General
• LGA1151 8th and 9th Intel®Core™ i7/i5/i3/Pentium®/
Xeon®
Note: 8th Gen CPU is compatible with V1.XX, 9th Gen CPU
is compatible with V1.XX and V2.XX BIOS
• BIOS: AMI 256 Mb SPI BIOS
• Chipset:
- PCE-7131: Intel® C246
- PCE-5131: Intel® Q370
- PCE-5031: Intel® H310
• System memory:
- PCE-7131: Supports dual channel DDR4 2400/2666
16GB per DIMM with ECC/non-ECC; Max. capacity is up
to 32GB
- PCE-5131/5031: Supports dual channel DDR4
2400/2666 16GB per DIMM without ECC; Max. capacity
is up to 32GB.
Note1: Please select Intel ECC supported processor to
enable ECC function.
Note2: Supports DDR4 1024M x 8 memory technology.
• SATA Ports:
- PCE-7131/5131 supports 5 x SATA3.0 ports with SW
Raid 0,1,5,10.
- PCE-5031 supports 4 x SATA3.0 ports without Raid
function.
• M.2 Ports: PCE-7131/5131 supports M.2 2280 type M
module and compatible to SATA3.0 and PCI Express 3.0
• Serial ports: Two RS-232 with pin headers
• Keyboard/mouse connector: Supports one standard
PS/2 keyboard and mouse connector and one external
6-pin header
• Watchdog timer: 255 level timer intervals
• USB 2.0: PCE-7131/5131/5031: 7 * USB 2.0 (Pin-
header*2+USB Type A*1+, 4 on backplane)
• USB 3.1:
- PCE-7131/5131: 6 * USB 3.1 (Gen1) (Pin-header*6),
1*USB3.1 (Gen2) (Rear I/O)
- PCE-5031: 2 * USB 3.1 (Gen1) (Pin-header*2), 1 * USB
3.1
(Gen2) (Rear I/O)
• GPIO: One programmable 8-bit GPIO pin-header
VGA Interface
• Chipset: Intel®HD Graphics
• Shared system memory is subject to OS
Ethernet Interface
• Chipset supports:
- LAN 1: I219LM (PCE-7131/5131); I219V(PCE-5031)
- LAN 2: I210AT (PCE-7131); I210AT (PCE-5131/5031)
• Connection: 2 x on-board RJ-45 connectors with LED
Specications
For more information on this and other Advantech prod-
ucts, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our sup-
port website at:
https://advt.ch/suppo1aa86
Register your products on our website and get 2 months
extra warranty for Free at:
http://www.register.advantech.com
This manual is for the PCE-5031/5131/7131
Part No. 2041503102
Printed in China
3rd Edition
October 2022

2 PCE-7131/5131/5031 Startup Manual
indicators.
Mechanical and Enviromental
• Dimensions: (L x W): 338 x 122 mm
• Power supply voltage: +12 V, +5 V, +3.3 V, +5 VSB
• Power requirements:
- CPU: Processor: Intel®Core™ i7-8700
- Memory: 2 DDR4 2666 8 GB DIMMs
- Voltage: +12 V, +5 V, +3.3 V, +5 VSB, -12 V, -5 V
- Current: 2.64 A, 1.23 A, 0.19 A, 0.09 A, 0.06 A, 0 A
- Operating temperature: 0 ~ 60 °C (depending on CPU)
• Weight: 0.5 kg (weight of board)
The board has a number of jumpers that allow you to con-
gure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
USB3C1 USB3 port1
LAN1 Intel® I219LM(PCE-7131/5131); Intel®
I219V(PCE-5031)
LAN2 Intel® I210AT(PCE-7131); Intel® I210AT
(PCE-5131/5031)
VGA1 VGA connector
KBMS1 External PS/2 keyboard and mouse
connector
KBMS2 Internal PS/2 keyboard and mouse
connector
HDAUD1 Advantech HD audio module expansion
pin-header
LPC1 LPC module expansion pin-header
Sysfan1 4 PIN fan power connector for support-
ing PWM or DC fan
LANLED1 LANLED
USB11 USB port 10
USB45 USB port 5, 6
USB3H3 USB port 7, 8
USB3H2 USB3 port 3, 4
USB3H1 USB3 port 2,3
COM1 RS-232 (9-pin Box Header)
COM2 RS-232 (9-pin Box Header)
LPT1 Parallel port
SATA0 / M.2 SATA port 0
SATA 1~5 SATA Port 1 ~ 5
SPI_CN1 CMOS ash jig pin-header
Jumpers and Connectors
SPI1 CMOS ROM
DP1 Display port pin-header 1
DP2 Display port pin-header 1
JCMOS1 Clear CMOS
JME1 Clear ME
JFP1 + JFP2 Power Switch/Reset connector/External
speaker/SATA HDD LED connector
JFP3
(Keyboard
Lock and
Power LED)
Power LED
Suspend: Fast ash (ATX/AT)
System On: ON (ATX/AT)
System O󰀨: OFF (ATX/AT)
CPUFAN1 CPU FAN Power connector
SYSFAN1 System FAN Power Connector for 1
system FAN
JCASE1 Case Open pin-header
JCASEOP_
SW1
Case Open switch for always open or
close
BAT1 Button battery socket
BAT2 External battery connector
GPIO1 GPIO pin header (SMD pitch-2.0 mm)
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
Jumpers
Label Function
JCMOS1 CMOS clear
JME1 Clear ME data
JWDT1 Watchdog timer output selection
JOBS1 SIO Monitor Alarm
JCMOS1/JME1: Clear CMOS/ME data
Closed Pins Result
1-2 Keep CMOS/ME data (Default)
2-3 Clear CMOS/ME data
123
Specications
Jumpers and Connectors (Cont.)

3 PCE-7131/5131/5031 Startup Manual
H/W monitor alarm (JOBS1)
Function Jumper Setting
Closed Enable OBS alarm (Default)
Open Disable OBS alarm
JWDT1: Watchdog timer output option
Closed Pins Result
1-2 Reserved
1 2 3
Board Layout
Software Installation
2-3 System reset (Default)
The drivers for the PCE-7131/5131/5031 are located on the
software installation CD. Please click through the folder and
Follow the on-screen instructions.
Caution! The computer is supplied with a battery-powered
real-time clock circuit. There is a danger of
explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Discard
used batteries according to the manufacturer’s
instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditons:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Jumpers and Connectors (Cont.)
Figure 1: Board Layout: Jumper and Connector Locations
Note: *PCE-5031 supports 4 SATA ports (SATA0~4) and one internal USB3.0 pin-header.
*PCE-5031 doesn’t feature NGFF(M.2).
*PCE-5031 supports 1 DP port.
CPUFAN1
JCASE1
SYSFAN1
JFP1~3
BAT2 DIMMA1
DIMMB1
SPI_CN1
SATA1~5
USB3H2
USB3H3
USB3H1
LANLED1
JOBS1
JWDT1
USB3C1
CPU1 DP2
DP1
SATA0
M.2
COM1
PCH1
COM2
GPIO1 LPC1
HDAUDIO1
KBMS2
Declaration of Conformity
Closed Open