Advantech PCE-7132 Installation and operation manual

PCE-7132/5132/5032 Startup Manual 1
Packing List
Before you begin installing your card, please make sure that
the following items have been shipped:
1. PCE-7132/5132/5032 PICMG 1.3 single host board
2. PCE-7132/5132/5032 Startup Manual
3. Serial ATA HDD data cables
4. COM port cable kit
5. Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of PCE-7132/5132/5032,
please refer to the user manual on the Advan-
tech website.
Note 2: Acrobat Reader is required to view any PDF
le. Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
PCE-7132/5132/5032 LGA1200 Intel®CoreTM
i9/i7/i5/i3/Pentium®ECC/non-ECC PICMG 1.3 Single
Host Board with (ECC/non-ECC) DDR4/M.2 (2280)/
Dual GbE LAN
Startup Manual
General
• LGA1200 10th Gen. Intel®Core™ i9/i7/i5/i3/Pentium®/
Xeon®
• BIOS: AMI 256 Mb SPI BIOS
• Chipset:
- PCE-7132: Intel® W480E
- PCE-5132: Intel® Q470E
- PCE-5032: Intel® H420E
• System memory:
- PCE-7132: Supports dual channel DDR4 2666/2933
32GB per DIMM with ECC/non-ECC; Max. capacity is
up to 64GB
- PCE-5132/5032: Supports dual channel DDR4
2666/2933 32GB per DIMM without ECC; Max. capacity
is up to 64GB.
Note: Please select Intel® ECC supported processor to
enable ECC function.
• SATA Ports:
- PCE-7132/5132 supports 6 x SATA3.0 ports with SW
Raid 0,1,5,10.
- PCE-5031 supports 4 x SATA3.0 ports without Raid
function.
• M.2 Ports: PCE-7132/5132 supports M.2 2280 type M
module and compatible to PCI Express 3.0
• Serial ports: Two RS-232 with pin headers
• Watchdog timer: 255 level timer intervals
• USB 2.0:
- PCE-7132/5132/5032: 6*USB 2.0 (USB Type
A*1+Rear*1, 4 on backplane)
• USB 3.2:
- PCE-7132/5132: 6 * USB 3.2 (Gen1) (Pin-header * 6), 2
* USB 3.2 (Gen2) (Rear I/O)
- PCE-5031: 2 * USB 3.1 (Gen1) (Pin-header * 2), 2 *
USB 3.2 (Gen1) (Rear I/O)
• GPIO: One programmable 8-bit GPIO pin-header
VGA Interface
• Chipset: Intel®HD Graphics
• Shared system memory is subject to OS
Ethernet Interface
• Chipset supports:
- LAN 1: I219LM(PCE-7132/5132); I219V(PCE-5032)
- LAN 2: I210AT(PCE-7132/51322); I210AT (PCE-5032)
• Connection: 2 x on-board RJ-45 connectors with LED
indicators
Specications
For more information on this and other Advantech prod-
ucts, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our sup-
port website at:
https://advt.ch/PCE-7132
https://advt.ch/PCE-5132
https://advt.ch/PCE-5032
Register your products on our website and get 2 months
extra warranty for Free at:
http://www.register.advantech.com
This manual is for the PCE-5032/5132/7132
Part No. 2041513201
Printed in China
2nd Edition
November 2022

2 PCE-7132/5132/5032 Startup Manual
Mechanical and Environmental
• Dimensions: (L x W): 338 x 122 mm
• Power supply voltage: +12 V, +5 V, +3.3 V, +5 V
SB
• Power requirements (Idle):
CPU: Processor: Intel
®
W-1290E
Memory: 2 DDR4 26666U 32GB
Voltage: +3.3 V, +5 V, +12 V
Current: 1.15 A, 1.54 A, 1.38 A
Operating temperature: 0 ~ 60 °C (depending on CPU)
• Weight: 0.5 kg (weight of board)
The board has a number of jumpers that allow you to con-
gure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
USB3C1 USB3 port1
USB3C2 USB3 port2
USB2C1 USB2 port1
LAN1 Intel® I219LM (PCE-7132/5132);
Intel® I219V (PCE-5032)
LAN2 Intel® I210-AT (PCE-7132/5132);
Intel® I210-AT (PCE-5032)
VGA1 VGA connector
KBMS1 External PS/2 keyboard and mouse
HDAUD1 Advantech HD audio module expansion
pin-header
LPC1 LPC module expansion pin-header
Sysfan1 4-PIN fan power connector for support-
ing PWM or DC fan
LANLED1 LANLED
USB2A1 USB2 port2
USB3H1 USB3 port 3,4
USB3H2 USB3 port 5,6 (PCE-7132/5132)
USB3H3 USB3 port 7,8 (PCE-7132/5132)
COM1
RS-232 (9-pin Box Header) COM2 RS-
232 (9-pin Box Header) LPT1 Parallel
port
SATA0 Port 0
SATA SATA port 1, 2, 3, 4, 5 (PCE-7132/5132);
SATA port 1, 2, 3 (PCE-5032)
Jumpers and Connectors
Jumpers
Label Function
JCMOS1 CMOS clear
JME1 Clear ME data
JWDT1 Watchdog timer output selection
JOBS1 SIO Monitor Alarm
JCMOS1/JME1: Clear CMOS/ME data
Closed Pins Result
1-2 Keep CMOS/ME data (Default)
2-3 Clear CMOS/ME data
Closed Open
H/W monitor alarm (JOBS1)
Function Jumper Setting
Closed Enable OBS alarm (Default)
Open Disable OBS alarm
JWDT1: Watchdog timer output option
Closed Pins Result
1-2 Reserved
2-3 System reset (Default)
The drivers for the PCE-7132/5132/5032 are located on the
Advantech o󰀩cial website. Please visit the o󰀩cial website
for downloading.
https://support.advantech.com/support/new_default.aspx
Caution! The computer is supplied with a battery-powered
real-time clock circuit. There is a danger of
explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Discard
used batteries according to the manufacturer’s
instructions.
123
1 2 3
Specications
Jumpers and Connectors (Cont.)
Software Installation

PCE-7132/5132/5032 Startup Manual 3
This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that may cause undesired operation.
Board Layout: Jumper and Connector Locations
Note: *PCE-5032 supports 4 SATA ports (SATA0~3) and one internal USB 3.2 pin-header.
*PCE-5032 doesn’t feature NGFF(M.2).
*PCE-5032 supports 1 DP port.
PCE-7132/5132/5032 Startup Manual 3
Board Layout
SYSTEMFAN1
CPUFAN1
DIMMA1
DIMMB1 SATA0~5 USB3H2 USB3H3
USB3H1
LANLED1
USB2A1
USB2C1
USB3C2
USB3C1
LAN12
VGA1
COM2
COM1
PCH1
BAT1
DP1&DP2
CPU1 LPC2
SPI_CN1
M.2
Board Layout
Declaration of Conformity