Advantech AIW-357 DK-G2U User manual

AIW-357 DK-G2U
User Manual

Applicability Type
AIW PN
MPN
Description
AIW-357 DK-G2U
XS5G03-GBO
MediaTek T700 NR SUB6/LTE FDD/LTE
TDD/WCDMA M.2 3052 module B key, W/O SIM
holder; w/o voice function; Only USB communication
interface, for USA, Europe, Japan and Taiwan
region

3
Revision History
Version
Date
Description
V1.0
2023-06-07
First issue
V1.1
2023-07-10
Section 2.10 edit LED Signal picture
V1.2
2023-08-16
Add Section 5.1 Product picture
V1.3
2023-08-23
1. Add Section 2.1 pin map schematic
2. Add Section 2.6.1~2.6.3 USIM N.C./ N.O. description

4
1 Overall Description
1.1 Function Overview
Features
Description
Dimensions
(L × W × H): 52 mm × 30 mm × 2.4 mm (Max)
Weight
8.7g
Voltage
3.135V ~3.63V, typical 3.3V
Operating Temperature
-30 ~ 70℃
Operating Humidity
less than 85% R.H.
Storage Temperature
-40 ~ 85℃
Storage Humidity
less than 60% R.H.
Extend Temperature
-30 ~ 80℃
Table 1-1 Features
Note:
Thermal solutions are necessary to be put on module, so that module can work smoothly
in operating temperature range. For example, thermal pad, heat sink, fan.
1.2 Product Specification and Frequency Bands
AIW-357 DK-G2U is standard version with GPS function.
Cellular
Item
AIW-357 DK-G2U
5G NR
Standard
3GPP Release 15
SA Bands
n1/2/3/5/7/8/20/25/28/30/38/40/41/48/66/71/ 77/78/79
NSA Bands
n1/2/3/5/8/20/28/38/41/66/71/77/78/79
Sub-6 CA
FDD/TDD+FDD/TDD DL CA*
DL 4x4 MIMO
n1/2/3/7/25/30/38/40/ 41/48/66/77/78/79
UL 2x2 MIMO
n41/77/78/79

5
Model
AIW-357 DK-G2U
4G LTE
LTE Category
Cat 12
LTE Bands
B1/2/3/4/5/7/8/12/13/14/17/18/19/20/25/26/
28/29/30/32/34/38/39/40/41/42/43/46/48/66/71
DL CA
4x4 MIMO, 3CC
UL CA
2CC
3G
UMTS/
WCDMA
Bands
B1/2/4/5/8
GPS
UL 2x2 MIMO
GPS/GLONASS/BeiDou/ Galileo
Frequency Band
L1
Table 1-2 Product Specification and Frequency Bands
1.3 Circuit Block Diagram
The circuit block diagram is shown in Figure 1-1.
The major functional units are listed below:
Power Management
Baseband Controller
MCP (4Gb LPDDR4X+4Gb Nand Flash)
RF Circuit
eSIM (option)

6
Figure 1-1 Circuit block diagram of the module

7
1.4 Application Interface
Features
Description
External Power Supply:
DC 3.3V Typical
USB Interface:
USB3.1 Gen1 x 1, USB2.0 x 1
Audio Interface:
I2S x 1
I2C Interface:
I2C × 1
USIM Interface:
USIM × 1, eSIM x 1 (optional)
RF Ipex4 connector:
RF Ipex4 connector × 4
Table 1-3 Application Interface
2 Description of the Application Interfaces
2.1 M.2 Key B Interface

8
Pin No.
AIW-357 DK-G2U M.2 module uses standard key B interface
Pin No.
74
+3.3V
CONFIG_2 (GND)
75
72
+3.3V
VIO_CFG
73
70
+3.3V
GND
71
68
NC
CONFIG_1 (GND)
69
66
SIM Detect (I) (1.8V)
RESET# (I) (1.8V)
67
64
COEX1 (IO) (1.8V)
ANTCTL3 (O) (1.8V)
65
62
COEX2 (IO) (1.8V)
ANTCTL2 (O) (1.8V)
63
60
COEX3 (IO) (1.8V)
ANTCTL1 (O) (1.8V)
61
58
MIPI2_D_SDATA (IO) (1.8V)
ANTCTL0 (O) (1.8V)
59
56
MIPI2_D_SCLK (O) (1.8V)
GND
57
54
NC
NC
55
52
NC
NC
53
50
NC
GND
51
48
NC
NC
49
46
NC
NC
47
44
I2C_IRQ# (I) (1.8V)
GND
45
42
I2C_SDA (IO) (1.8V)
NC
43
40
I2C_SCL (O) (1.8V)
NC
41
38
NC
GND
39
36
USIM1_PWR (O)
USB3.0_RX+
37
34
USIM1_DATA (IO)
USB3.0_RX-
35
32
USIM1_CLK (O)
GND
33
30
USIM1_RESET (O)
USB3.0_TX+
31
28
I2S0_LRCK (IO) (1.8V)
USB3.0_TX-
29
26
W_DISABLE2# (I) (3.3/1.8V)
GND
27
24
I2S0_DO (O) (1.8V)
DPR (I) (1.8V)
25
22
I2S0_DI (I) (1.8V)
WOWWAN# (IO) (1.8V)
23
20
I2S0_BCK (IO) (1.8V)
CONFIG_0 (GND)
21
Notch
Notch

9
Notch
Notch
Notch
Notch
Notch
Notch
10
LED1# (O) (3.3V)
GND
11
8
W_DISABLE1# (I) (3.3/1.8V)
USB_D-
9
6
FULL_CARD_POWER_OFF# (I)
(3.3/1.8V)
USB_D+
7
4
+3.3V
GND
5
2
+3.3V
GND
3
CONFIG_3 (NC)
1
Figure 2-1 AIW-357 DK-G2U Pin Map

10
Pin
Pin Name
Description
Voltage
Type
1
CONFIG_3
Setting vale: NC
NC
DO
The interface of AIW-357 DK-G2U
module is configured as the WWAN –
PCIe Gen3, USB3.1 Gen1
2
+3.3V
Power supply for Module
3.135-3.63V
PI
3
GND
Module ground pin
4
+3.3V
Power supply for Module
3.135-3.63V
PI
5
GND
Module ground pin
6
FULL_CARD
Pull high to 1.4V~module input
3.3/ 1.8V
DI
_POWER_OFF#
voltage to enable power of the module
7
USB_D+
USB2.0 differential data –plus
AIO
8
W_DISABLE1#
The pin use for WWAN disable,
3.3/ 1.8V
DI
active low
9
USB_D-
USB2.0 differential data –minus
AIO
10
LED1#
Open drain, active low signal.
3.3V
DO
The signal is used to allow the add-in
card to provide status indicators
via LED devices that will be provided
by the system.
11
GND
Module ground pin
12
Notch
Notch
13
Notch
Notch
14
Notch
Notch
15
Notch
Notch
16
Notch
Notch
17
Notch
Notch
18
Notch
Notch
19
Notch
Notch