Advantech WISE-1510 User manual

User Manual
WISE-1510
M2.COM LoRa IoT Node

WISE-1510 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
ARM is trademarks of ARM Corporation.
Freescale is trademarks of Freescale Corporation.
Microsoft Windows are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2006E15100 Edition 1
Printed in China March 2019

iii WISE-1510 User Manual
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
This module is intended for OEM integrator. The OEM integrator is responsible for
the compliance to all the rules that apply to the product into which this certified RF
module is integrated.
Additional testing and certification may be necessary when multiple modules are
used.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and oper-
ated. The end user has to be informed that the FCC radio-frequency exposure guide-
lines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate
this equipment.
If the labelling area is small than the palm of the hand, then additional FCC part 15.19
statement is required to be available in the users manual: This device complies with

WISE-1510 User Manual iv
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains
TX FCC ID: M82-WISE1510 ".
If the labelling area is larger than the palm of the hand, then the following FCC part
15.19 statement has to also be available on the label: This device complies with Part
15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IC
This radio transmitter has been approved by Industry Canada to operate with the
antenna types listed below with the maximum permissible gain indicated. Antenna
types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supéri-
eur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
This device complies with Industry Canada license-exempt RSS standard(s). Opera-
tion is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appa-
reils radio exempts de licence. L'exploitation est autorisée aux deux conditions suiv-
antes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepti-
ble d'en compromettre le fonctionnement.
This radio transmitter (9404A-WISE1510) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain indi-
cated. Antenna types not included in this list, having a gain greater than the maxi-
mum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (9404A-WISE1510) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou
dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Antenna list:
Part No. MPN Description
1750008625-01 TH-915i Dipole Ant. SUB-1G 1.8dBi SMA/M BLK 902-928 IPX6

v WISE-1510 User Manual
IMPORTANT NOTE
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with min-
imum distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This module is intended for OEM integrator. The OEM integrator is responsible for
the compliance to all the rules that apply to the product into which this certified RF
module is integrated.
Additional testing and certification may be necessary when multiple modules are
used.
Any changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and oper-
ated. The end user has to be informed that the IC radio-frequency exposure guide-
lines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate
this equipment. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains
IC: 9404A-WISE1510 ".
The Host Model Number (HMN) must be indicated at any location on the exterior of
the end product or product packaging or product literature which shall be available
with the end product or online.
低功率電波輻射性電機管理辦法
茲 「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能」。
(1) 「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾
現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指
依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、
科學及醫療用電波輻射性電機設備之干擾」。
(2) 「本模組於取得認證後將依規定於模組本體標示審驗合格標籤 , 並要求平台
廠商於平台上標示 「本產品內含射頻模組 CC AF 17 LP 640 T 0」。

WISE-1510 User Manual vi
Package List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
1 x WISE-1510
1 x Screw for WISE-1510
1 x China RoHs Notice
Optional Accessories
Development Board
Ordering Information
Part No. Description
1750008598-01 Sub G antenna Dipole L=195mm, 1dBi 902~928 MHz
1750008599-01 Sub G antenna Dipole L=195mm, 1dBi 863~870 MHz
1750008569-01 Antenna Cable SMA to MHF4 L=300mm
1700015038 FPC Cable 10P-0.5mm 7.9cm for DCU2.0
9696WED200E ASS'Y WISE-ED20 A101-1 M2.COM Daughter
1931000590 Screw M2.5x5L F/S D=5.3 H=0.8 (1+) ST Ni
1700023619-01 A cable USB-A 4P(M)/micro USB 5P(M) 1m ADAM-T212
1700025876-01 M cable USB-A 4P(M)/Plug-in 2P-5.0 90CM
XRISC-ADP-10HW-AG ADP A/D 100-240V 10W 5V WM
193A231540 POST F=M3*6L M=M3*6L D=5 d=2.88 B=5 H=15 Cu
Part No. Description
9696150000E ASS'Y WISE-DB1500 A101-1 M2.COM CARRIER
Part No. WISE-1510WMB-SDA1N
Frequency Band 902-928MHz for North America (LoRa)
Part No. WISE-1510WMB-SDA1E
Frequency Band 863-870MHz for Europe (LoRa)
Part No. WISE-1510WMB-SDA1J
Frequency Band 902~928MHz for Japan (LoRa)
Part No. WISE-1510WMB-SDA1C
Frequency Band 470~510MHz for China (LoRa)
Part No. WISE-1510WMB-SDA1T
Frequency Band 920~925MHz for Taiwan (LoRa)

vii WISE-1510 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

WISE-1510 User Manual viii

ix WISE-1510 User Manual
Contents
Chapter 1 Product Overview................................1
1.1 Introduction ...............................................................................................2
1.1.1 Product Features ..........................................................................2
Chapter 2 H/W Installation....................................5
2.1 Board Connector.......................................................................................6
Figure 2.1 Card Edge Bevel ........................................................6
Figure 2.2 Card Edge Outline-Topside........................................7
Figure 2.3 Card Edge Outline-Backside......................................7
2.2 Module Outline..........................................................................................8
Figure 2.4 Type A 2230...............................................................8
2.3 Connector Specifications ..........................................................................9
2.3.1 Top Side Connector Physical Dimensions....................................9
2.3.2 Carrier Board Connection Length...............................................10
Figure 2.5 Carrier Board Connection Length.............................10
2.3.3 Carrier Board Connector Height .................................................10
Figure 2.6 H3.2-D3....................................................................10
2.4 WISE-1510 Pin-Out Map.........................................................................11
Figure 2.7 M.2 Connector..........................................................12
2.5 Quick Starter of WISE-1510....................................................................12
2.5.1 LoRaWAN and Proprietary LoRa (WISELink 1.0 and WISELink
2.0)..............................................................................................13
2.5.2 Class A and Class C...................................................................14
2.5.3 Data rate vs Distance..................................................................15
Figure 2.8 Data rate and Distance.............................................15
Chapter 3 How to choose your solution on
WISELink............................................17
3.1 Parking Lot: WISELink 1.0 with Class A, ABP mode..............................18
Figure 3.1 Work Flow on Parking Lot solution...........................18
3.2 Aquaculture: WISELink 1.0 with Class C, ABP mode.............................19
3.3 Environment Monitoring: WISELink 2.0 with Class A, OTAA mode........20
Figure 3.2 Work Flow on Environment Monitoring solution.......20
3.4 Factory: WISELink 2.0 with Class C, OTAA mode (Default SDK Setting) ..
21 Figure 3.3 Work Flow on Factory solution.................................21
Chapter 4 Development Environment Setup....23
4.1 File Structure...........................................................................................24
4.1.1 Mbed OS.....................................................................................24
4.1.2 WISELink....................................................................................24
4.2 OS Version..............................................................................................24
4.3 Environment Setup Procedure................................................................24
4.3.1 Installation...................................................................................25
4.3.2 Configuration...............................................................................26
4.3.3 Compilation.................................................................................26
4.4 Firmware Upgrade ..................................................................................27

WISE-1510 User Manual x
Chapter 5 Binding Process between WISE-1510
and WISE-3610.................................. 33
5.1 CLI Command Description...................................................................... 34
5.2 WISELink 1.0 with Class A, ABP mode.................................................. 35
5.2.1 Settings on WISE-1510 .............................................................. 35
5.2.2 Settings on WISE-3610 .............................................................. 35
5.3 WISELink 1.0 with Class C, ABP mode.................................................. 38
5.3.1 Settings on WISE-1510 .............................................................. 38
5.3.2 Settings on WISE-3610 .............................................................. 39
5.4 WISELink 2.0 with Class A, OTAA mode................................................ 42
5.4.1 Settings on WISE-1510 .............................................................. 42
5.4.2 Settings on WISE-3610 .............................................................. 43
5.5 WISELink 2.0 with Class C, OTAA mode ............................................... 47
5.5.1 Settings on WISE-1510 .............................................................. 47
5.5.2 Settings on WISE-3610 .............................................................. 47
Appendix A Application Interface Description
(WISELink Application) ....................51
A.1 Application Interface Description (WISELink Application)....................... 52
Appendix B Application Sample Code Flow .......53
B.1 Application Sample Code Flow............................................................... 54
Appendix C Sensor Data Format.......................... 55
C.1 Sensor Data Format................................................................................ 56