Advantech DS-410 User manual

User Manual
DS-410
Palm-Sized Mini-PC with
HDMI VGA COM Ports

DS-410 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2023
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
Award is a trademark of Award Software International, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel® and ATOM® are trademarks of Intel Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
CHRONTEL is a trademark of Chrontel Inc.
All other product names or trademarks are properties of their respective owners.
For more information about this and other Advantech products, please visit our web-
site at: http://www.advantech.com/ For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/
Part No. 2006S41000 Edition 1
Printed in Taiwan April 2023

iii DS-410 User Manual
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.

DS-410 User Manual iv
Declaration of Conformity
FCC Class B
Declaration based on 47 CFR 15.19(a)(3)
“This device complies with part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.”
Statement for Class B based on 47 CFR 15.105(b)
“Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v DS-410 User Manual
Warnings, Cautions, and Notes
Warning! Warnings indicate conditions that if not observed can cause personal
injury!
Les avertissements indiquent des conditions qui, si elles ne sont pas
observées, peuvent causer des blessures!
Caution! Cautions are included to help prevent hardware damage and data
losses. For example,
“Batteries are at risk of exploding if incorrectly installed. Do not attempt
to recharge, force open, or heat the battery. Replace the battery only
with the same or equivalent type as recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.”
Des précautions sont incluses pour vous aider à éviter d'endommager le
matériel ou à perdre des données. par exemple.
Une pile neuve risque d'exploser si elle n'est pas installée correctement.
N'essayez pas de recharger, d'ouvrir de force ou de chauffer la batterie.
Remplacez la pile uniquement par le même type ou un type équivalent
recommandé par le fabricant. Jetez les piles usagées conformément
aux instructions du fabricant.
Note! Notes provide additional optional information.
Les notes fournissent des informations supplémentaires facultatives.
Warning! The equipment is not suitable for use in locations where children are
likely to be present.
Cet équipement ne convient pas à une utilisation dans des lieux pouvant
accueillir des enfants
Warning! To avoid risk of electric shock, this equipment must only be connected
to grounded supply mains.
Pour éviter tout risque d'électrocution,cet équipement ne doit être
branché qu'au réseau d'alimentation avec une terre de protection.
Warning! Restricted access area: area accessible only to skilled persons and
qualified persons with the proper authorization.

DS-410 User Manual vi
Packing List
Before system installation, check that the items listed below are included and in good
condition. If any item does not accord with the list, contact your dealer immediately.
1 x DS-410 series player
1 x China RoHS Sheet
4 x Rubber foot and screws
1 x 19V power adapter
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient over-voltage.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following occurs, have the equipment checked by service person-
nel:
–The power cord or plug is damaged.
–Liquid has penetrated the equipment.
–The equipment has been exposed to moisture.
–The equipment is malfunctioning, or does not operate according to the user
manual.
–The equipment has been dropped and damaged.
–The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -20° C (-4° F) or above 60° C (140° F) as this may damage the compo-
nents. The equipment should be kept in a controlled environment.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at
the operator’s position does not exceed 70 dB (A).
18. RESTRICTED ACCESS AREA: The equipment should only be installed in a
Restricted Access Area.

vii DS-410 User Manual
DISCLAIMER: These instructions are provided according to IEC 704-1 standards.
Advantech disclaims all responsibility for the accuracy of any statements contained
herein.
Consignes de sécurité
1. Lisez attentivement ces instructions de sécurité.
2. Conservez ce manuel de l'utilisateur pour référence ultérieure.
3. Débranchez cet appareil de toute prise secteur avant le nettoyage. Utilisez un
chiffon humide. N'utilisez pas de détergents liquides ou en aérosol pour le net-
toyage.
4. Pour les équipements enfichables, la prise de courant doit être située à proxim-
ité de l'équipement et doit être facilement accessible.
5. Gardez cet équipement à l'abri de l'humidité.
6. Placez cet équipement sur une surface fiable lors de l'installation. Le laisser
tomber ou le laisser tomber peut causer des dommages.
7. Les ouvertures sur le boîtier sont destinées à la convection de l'air. Protégez
l'équipement de la surchauffe. NE COUVREZ PAS LES OUVERTURES.
8. Assurez-vous que la tension de la source d'alimentation est correcte avant de
connecter l'équipement à la prise de courant.
9. Positionnez le cordon d'alimentation de sorte que personne ne puisse marcher
dessus. Ne placez rien sur le cordon d'alimentation.
10. Tous les avertissements et mises en garde sur l'équipement doivent être notés.
11. Si l'équipement n'est pas utilisé pendant une longue période, débranchez-le de
la source d'alimentation pour éviter tout dommage dû à une surtension transi-
toire.
12. Ne jamais verser de liquide dans une ouverture. Cela pourrait provoquer un
incendie ou un choc électrique.
13. Ne jamais ouvrir l'équipement. Pour des raisons de sécurité, l’équipement ne
doit être ouvert que par du personnel qualifié.
14. Si l’une des situations suivantes se produit, faites vérifier l’équipement par le
personnel de service:
–Le cordon d'alimentation ou la fiche est endommagé
–Un liquide a pénétré dans l'équipement.
–L'équipement a été exposé à l'humidité.
–L'équipement ne fonctionne pas bien ou vous ne pouvez pas le faire fonction-
ner conformément au manuel d'utilisation.
–L'équipement est tombé et a été endommagé.
–L'équipement présente des signes évidents de rupture.
15. NE PAS LAISSER CET ÉQUIPEMENT DANS UN ENVIRONNEMENT O LA
TEMPÉRATURE DE STOCKAGE POURRAIT ÊTRE INFÉRIEURE À -20 ° C (-
4 ° F) OU SUPÉRIEURE À 60 ° C (140 ° F). CELA POURRAIT ENDOMMAGER
L'ÉQUIPEMENT. L’ÉQUIPEMENT DOIT ÊTRE DANS UN ENVIRONNEMENT
CONTRÔLÉ.
16. ATTENTION: DANGER D'EXPLOSION EN CAS DE REMPLACEMENT
INCORRECT DE LA BATTERIE. REMPLACEZ UNIQUEMENT AVEC LE
MÊME TYPE OU LE TYPE ÉQUIVALENT RECOMMANDÉ PAR LE FABRI-
CANT, DÉPOSEZ LES PILES UTILISÉES SELON LES INSTRUCTIONS DU
FABRICANT.
17. Le niveau de pression acoustique au poste de l'opérateur selon la norme CEI
704-1: 1982 n'est pas supérieur à 70 dB (A).

DS-410 User Manual viii
18. ZONE D'ACCÈS RESTRICTED: L'équipement ne doit être installé que dans
une zone d'accès restreint.
AVERTISSEMENT: Cet ensemble d'instructions est donné conformément à la norme
CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des déclara-
tions contenues dans ce document.
DS-410 Series Part Number
Remark
DS-410GB-U0A1E DS-410, J6412, Barebones, 4GB LPDDR4
DS-410GB-U1A1E DS-410, J6412, Barebones, 8GB LPDDR4
DS410GB2301-T DS410GB2401-T DS410GB2501-T DS410GB2601-T DS410GB2701-T
DS410GB2302-T DS410GB2402-T DS410GB2502-T DS410GB2602-T DS410GB2702-T
DS410GB2303-T DS410GB2403-T DS410GB2503-T DS410GB2603-T DS410GB2703-T
DS410GB2304-T DS410GB2404-T DS410GB2504-T DS410GB2604-T DS410GB2704-T
DS410GB2305-T DS410GB2405-T DS410GB2505-T DS410GB2605-T DS410GB2705-T
DS410GB2306-T DS410GB2406-T DS410GB2506-T DS410GB2606-T DS410GB2706-T
DS410GB2307-T DS410GB2407-T DS410GB2507-T DS410GB2607-T DS410GB2707-T
DS410GB2308-T DS410GB2408-T DS410GB2508-T DS410GB2608-T DS410GB2708-T
DS410GB2309-T DS410GB2409-T DS410GB2509-T DS410GB2609-T DS410GB2709-T
DS410GB2310-T DS410GB2410-T DS410GB2510-T DS410GB2610-T DS410GB2710-T

ix DS-410 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Product Features....................................................................................... 2
1.2.1 General ......................................................................................... 2
1.2.2 Display .......................................................................................... 2
1.2.3 Thermal Solution........................................................................... 2
1.3 Hardware & Software Specifications......................................................... 2
1.4 Mechanical Specifications........................................................................ 3
1.4.1 Dimensions ................................................................................... 3
Figure 1.1 Dimensions................................................................. 3
1.4.2 Weight........................................................................................... 3
1.5 Power Requirements................................................................................. 4
1.5.1 System Power............................................................................... 4
1.5.2 RTC Battery .................................................................................. 4
1.6 Environmental Specifications.................................................................... 4
1.6.1 Operating Temperature................................................................. 4
1.6.2 Relative Humidity.......................................................................... 4
1.6.3 Storage Temperature.................................................................... 4
1.6.4 Vibration Loading During Operation.............................................. 4
1.6.5 Shock During Vibration ................................................................. 4
1.6.6 EMC.............................................................................................. 4
Chapter 2 Hardware Configuration......................5
2.1 DS-410 Series I/O..................................................................................... 6
Figure 2.1 DS 410 I/O.................................................................. 6
2.1.1 LED............................................................................................... 6
Figure 2.2 Power ......................................................................... 6
Figure 2.3 LED - HDD.................................................................. 6
2.1.2 Power On/Off ................................................................................ 6
Figure 2.4 Power Button.............................................................. 6
2.1.3 VGA Connector............................................................................. 7
Figure 2.5 VGA Connector .......................................................... 7
2.1.4 USB 3.0 Connector....................................................................... 7
Figure 2.6 USB Connector........................................................... 7
2.1.5 LAN Connector ............................................................................. 8
Figure 2.7 RJ45 Connector.......................................................... 8
2.1.6 Wi-Fi Antenna ............................................................................... 8
Figure 2.8 SMA Connector .......................................................... 8
2.1.7 RJ11 Connector............................................................................ 9
2.1.8 HDMI Connector ......................................................................... 10
Figure 2.9 HDMI Connector...................................................... 10
2.2 Hardware Installation .............................................................................. 11
2.2.1 SSD Installation .......................................................................... 11
2.3 Jumpers .................................................................................................. 12
Figure 2.10Jumper Layout.......................................................... 12
2.3.1 Clear CMOS (JCMOS1).............................................................. 12
2.3.2 AT/ATX (PSON1)........................................................................ 12
Figure 2.11.................................................................................. 12
Chapter 3 BIOS Settings.....................................13
3.1 BIOS Introduction.................................................................................... 14

DS-410 User Manual x
3.2 Entering the Setup .................................................................................. 15
3.2.1 Main Setup.................................................................................. 15
3.2.2 Advanced.................................................................................... 16
3.2.3 Advanced → CPU Configuration ................................................ 17
3.2.4 Advanced → Power & Performance........................................... 18
3.2.5 Advanced → PCH-FW Configuration ......................................... 19
3.2.6 Advanced → ACPI Settings........................................................ 22
3.2.7 Advanced → IT5121 HW Monitor............................................... 23
3.2.8 Advanced → IT5121 Super IO Configuration ............................. 24
3.2.9 Advanced → Trusted Computing................................................ 26
3.2.10 Advanced → S5 RTC Wake Settings ......................................... 27
3.2.11 Advanced → USB Configuration ................................................ 28
3.2.12 Advanced → Network Stack Configuration................................. 29
3.3 Chipset.................................................................................................... 30
3.3.1 Chipset → System Agent (SA) Configuration............................. 30
3.3.2 Chipset → PCH-IO Configuration............................................... 32
3.4 Security ................................................................................................... 37
3.4.1 Security → Secure Boot ............................................................. 38
3.5 Boot......................................................................................................... 40
3.6 Save & Exit ............................................................................................. 41

Chapter 1
1General Information
This chapter details background
information on the DS-410 series.

DS-410 User Manual 2
1.1 Introduction
The Advantech DS-410 is a miniPC powered by Intel® processors that delivers 4K
UHD output via HDMI, and HD output via VGA. DS-410 is designed to save space,
and features diverse built-in I/O — including HDMI, VGA, USB 3.1, RS232 (RJ11),
and dual-LAN (RJ-45). It enables media playback and display, and is ideal for all-in-
one signage applications with space constraints.
1.2 Product Features
1.2.1 General
Supports Intel J6412
Supports HDMI 2.0, VGA
Supports M.2 2242 M Key for storage
Built-in M.2 2230 E Key slot for Wi-Fi module expansion
1.2.2 Display
1 x HDMI 2.0 @3840x2160 60Hz
1 x VGA @1920x1080 30Hz
1.2.3 Thermal Solution
Fanless
1.3 Hardware & Software Specifications
CPU: Intel J6412
System Chipset: Built-in CPU
Graphic Chipset: Integrated graphics built-in processor
BIOS: AMI uEFI 256 Mbit
System Memory: 4GB or 8GB DDR4 on board
Storage: M.2 2242 M Key (SATA SSD)
SUSI: SUSI is a special hardware management tool, made by Advantech, that
provides DS-410 with a Win10 IoT image. It also provides the following func-
tions:
–Watchdog timer
–Hardware monitor
–System information
I/O Interfaces:
–1 x HDMI 2.0
–1 x VGA
–2 x USB 3.0
–1 x RJ11 (2 x RS232, 1 x system On/Off pin)
Ethernet Chipset:
–Speed: 10/100/1000 Mbps
–Interface: 2 x RJ45 jacks with LED
–Standard: IEEE 802.3z/ab (1000 Base-T) or IEEE 802.3u 100 Base-T com-
pliant

3 DS-410 User Manual
Chapter 1 General Information
Resolution:
–1 x HDMI 2.0, @3840x2160 60Hz
–1 x VGA @1920x1080 30Hz
Expansion: 1 x M.2 2230 E Key (for Wi-Fi modules)
1.4 Mechanical Specifications
1.4.1 Dimensions
124 x 116 x 28 mm (L x W x H)
Figure 1.1 Dimensions
1.4.2 Weight
0.41 kg

DS-410 User Manual 4
1.5 Power Requirements
1.5.1 System Power
Minimum power input: DC 19V, 3.42A
1.5.2 RTC Battery
Battery 3V 195mAH BR2032
1.6 Environmental Specifications
1.6.1 Operating Temperature
0 - 40 °C @0.7m/s air flow
1.6.2 Relative Humidity
95% @ 40 °C (Non Condensing)
1.6.3 Storage Temperature
-20 - 60 °C (-4 - 140 °F)
1.6.4 Vibration Loading During Operation
0.5 Grms, IEC 60068-2-64, random, 5 ~ 500 Hz, 1 hr/axis.
1.6.5 Shock During Vibration
20 G, IEC 60068-2-27, half sine, 11 ms duration
1.6.6 EMC
CE, FCC Class B

Chapter 2
2Hardware
Configuration
This chapter introduces external I/
O and the installation of DS-410
series hardware.

DS-410 User Manual 6
2.1 DS-410 Series I/O
Figure 2.1 DS 410 I/O
2.1.1 LED
When the LED indicator displayed below turns green, it indicates a power on status.
Figure 2.2 Power
When LED indicator displayed below turns orange it indicates the SSD status
Figure 2.3 LED - HDD
2.1.2 Power On/Off
Press the button indicated below to power DS-410 on/off.
Figure 2.4 Power Button

7 DS-410 User Manual
Chapter 2 Hardware Configuration
2.1.3 VGA Connector
DS-410 provides one integrated 15-pin female VGA digital video interface, which
supports up to 1920 x 1080 30Hz. Please refer to this pin assignment.
Figure 2.5 VGA Connector
2.1.4 USB 3.0 Connector
DS-410 supports 2 x USB 3.0 interfaces. The USB interfaces complies with USB
UHCI, Rev. 3.0 standards. Please refer to this pin assignment. USB 3.0 connectors
contain legacy pins to interface with USB 2.0 devices, and a new set of pins for USB
3.0 connectivity.
Figure 2.6 USB Connector
Pin Signal Name Pin Signal Name
1 Red 2 Green
3 Blue 4 NC
5 GND 6 GND
7 GND 8 GND
9 5V 10 GND
11 NC 12 DDAT
13 H-SYNC 14 V-SYNC
15 DCLK
Pin Signal Name Pin Signal Name
1 +5V 2 USB_Data-
3 USB_Data+ 4 GND
5 SSRX- 6 SSRX+
7 GND 8 SSTX-
9 SSTX+

DS-410 User Manual 8
2.1.5 LAN Connector
DS-410 provides 2 x RJ45 LAN interface connector, fully compliant with IEEE802.3u
10/100/1000 Base-T CSMA/CD standards. The Ethernet port provides 1 x standard
RJ-45 jack connector with LED indicators to show its Active/Link status and speed
status.
Figure 2.7 RJ45 Connector
2.1.6 Wi-Fi Antenna
DS-410 provides 2 x Wi-Fi antenna connectors to connect with the SMA antenna.
Figure 2.8 SMA Connector
LAN Port Pin Assignments
Pin Signal
1 MDI0+
2 MDI0-
3 MDI1+
4 MDI1-
5 GND
6 GND
7 MDI2+
8 MDI2-
Right side LED: Green LED
Link Status Always turn on without transmitting/receiving data
Activity status Flash
Left side LED: Green/Orange LED
Status Display
10Mbps Always off
100Mbps Green
1000Mbps Orange

9 DS-410 User Manual
Chapter 2 Hardware Configuration
2.1.7 RJ11 Connector
DS-410 provides 2 x RS232 (Tx/Rx) and 1 x stem Power On/Off Control pin. Order
the cable PN (1700034193-01) to accommodate other kiosks or mini-PC setup
demands.
RJ11 Port Pin Assignments
Pin Signal
1 COM0_TXD
2 COM0_RXD
3 POWERBUTTON#
4 GND
5 COM1_TXD
6 COM1_RXD

DS-410 User Manual 10
2.1.8 HDMI Connector
The HDMI (High-Definition Multimedia Interface) provides an all-digital audio/video
interface to transmit the uncompressed audio/video signals and is HDCP compliant.
Connect the HDMI audio/video device to this port. HDMI technology can support a
maximum resolution of 3840 x 2160 @ 60 Hz but the actual resolution supported
depends on the monitor being used.
Figure 2.9 HDMI Connector
HDMI Pin Assignments
Pin Signal
1 TMDS Data 2+
2 TMDS Data 2 shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 shield
9 TTMDS Data 0-
10 TMDS Clock+
11 TMDS Clock shield
12 TMDS Clock-
13 CEC
14 Reserved
15 SCL
16 SDA
17 DDC/CEC Ground
18 +5V
19 Hot Plug Detect