Advantech MIO-5373 Installation and operation manual

MIO-5373 Startup Manual 1
Before you begin installing your board, please make sure
that the following items have been shipped:
• 1 x MIO-5373 SBC
• 1 x Startup Manual (P/N: 2046537300)
• 1 x SATA Cable 30cm (P/N: 1700006291)
• 1 x SATA Power Cable 35cm (P/N: 1700018785)
• 1 x Audio JACK*3 Cable 20cm (P/N: 1700019584)
• 1 x COM RS-232 Cable 20cm (P/N: 1700030404-01)
• 1 x MIO-5373 Heatsink for 0 ~ 60°C
(P/N: 1960091427N001)
• 1 x Mini Jumper (P/N: 9689000002)
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note1: For detailed contents of MIO-5373, please refer
to information on the support website: http://sup-
port.advantech.com.tw/
Note2:  AdobeReaderisrequiredtoviewanyPDFle.
Adobe Reader can be downloaded at: http://get.
adobe.com/tw/reader/otherversions/ (Adobe is
the trademark of Adobe Systems Incorporated)
MIO-5373 3.5” MI/O-Compact SBC, 8th Gen. Intel® Core™
U-series (i7/i5/i3/Celeron®), DDR4, eMMC, HDMI, DP, 48-bit
LVDS, 2 GbE, M.2 B-key 2280, DC-in 12-24V, iManager
Startup Manual
General
• CPU:
- Intel® Core™ i7-8665UE (Quad-Core, 1.70GHz)
- Intel® Core™ i5-8365UE (Quad-Core, 1.60GHz)
- Intel® Core™ i3-8145UE (Dual-Core, 2.20GHz)
• System Memory: Dual Channel/SODIMM DDR4-2400MT/s, up
to 32GB
• BIOS: AMI EFI 256Mbit
• Watchdog Timer: 65536 level, 0~65535 sec
• TPM 2.0
• iManager 3.0: Yes
• Expansion Interface:
- M.2:
1 x M.2 E-key 2230
1 x M.2 B-key 2280 (SATA or NVMe PCIex2), 3042 LTE
module (support USB2.0 only), optional M-key 2280
NVMe PCIex4.
- MI/O Extension connector: 4 PCIex1, 1 PCIex4, USB2.0,
LPC, SMBus, Line-out, 12V/5V Power supply
• Battery: Lithium 3V/ 210mAH
• Audio:SupportsHighDenitionAudio(HD),line-in,line-
out, Mic-in
Display
• Controller: Intel® WHL-U SoC integrated, HDMI display
output ALC-888S for 48-bit LVDS display output
• Maximum Resolution:
LCD:
- LVDS Dual Channel 48-bit up to 1920 x 1200
- Option eDP1.4 up to 4096x2304@60Hz
HDMI/DP:
- 1 Port HDMI1.4 up to 4096x2160@30/24Hz
- 1 Port DP1.2 up to 4096x2306@60Hz
• Multiple Display: Triple simultaneous displays by 48-bit
LVDS/eDP+HDMI+DP
Ethernet Interface
• Speed: 10/100/1000 Mbps
• Controller: GbE1 - Intel i219, GbE2 - Intel i210-AT
• Connector: RJ45 x2
SpecicationsPacking List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/
This manual is for MIO-5373.
Part No. 2046537300
Printed in China
1st Edition
February 2020

2 MIO-5373 Startup Manual
I/O
• Internal I/O: 2 x SATA 6Gb/s, 2 x USB2.0, 1 x
RS232/422/485, 16-bit GPIO, Inverter, SMBus, I2C*, HD
Audio, LVDS, System FAN
• Rear I/O: 4 x USB3.1, HDMI, DP, 2 x RJ-45, 1 x
RS232/422/485, 1 x DC-Jack(*optional)
• MI/O Expansion: 4 PCIex1, 1 PCIex4, USB2.0, LPC,
SMBus, Line-out, 12V/5V Power supply
• Power Connector Type:
Default support 2 x 2 pin ATX power connector, DC Jack
is supported by request
Mechanical and Environmental
• Dimensions (L x W): 146 x 102 mm (5.7 x 4 inches)
• Power Supply Type: ACPI support for ATX only
• Power Requirement: Vin: 12V-24V +/- 10%
• Power Consumption:
- Max:
i7-8665UE: 61.9 W (12V)
i7-8665UE: 66.15W (24V)
i5-8365UE: TBD
i3-8145UE: TBD
- Typical: Idle mode in Windows 10
i7-8665UE: 7.42 W (12V)
i7-8665UE: 6.61 W (24V)
i5-8365UE: TBD
i3-8145UE: TBD
• Operating Temperature: 0~60°C (32~140°F)
• Weight: 0.67 kg (reference weight of total package)
Jumpers and Connectors
The board has a number of connectors and jumpers that
allowyoutocongureyoursystemtosuityourapplication.
The table below lists the function of each of the jumpers and
connectors.
Jumpers
Label Function
J1
AT/ATX mode selection
J2
RI# 5V/12V selection pin for CN9
J3 Panel Voltage Selection
J4 LVDS JEIDA and VESA mode Selection
SW1 Clear CMOS
Connector
Lable Function
CN1 DDR4 SODIMM 260P/H5.2mm
CN2 DDR4 SODIMM 260P/H9.2mm
CN3 DC input Connector
CN5 RTC Battery Connector
CN8 Power/LED/Case Open/Buzzer Connector
CN9 COM port Connector
(RS232+RS422+RS485)
CN10 COM port Connector
(RS232+RS422+RS485)
CN11 RJ45 Connector (2 port)
CN12 Inverter Connector
CN13 LVDS Connector
CN14 eDP Connector
CN15 HDMI and DP++ Connector
CN16 Key E Connector
CN17 Key B and Key M(option) Connector
CN20 SIM card Connector
CN22 USB3.1 Connector (2 ports)
CN23 USB3.1 Connector (2 ports)
CN24 Internal USB Connector
CN25 HDD Power Connector
CN26 HDD Connector
CN27 HDD Connector
CN28 GPIO/RS232 Connector
CN29 Audio Connector
CN30 GPIO/RS232 Connector
CN30A1 MIOe Connector
CN31 I2C Bus Connector
CN32 System FAN Connector
CN35 CANBus Connector
CN36 SMBus Connector
CN37 DC input Connector (Adapter)
Specications(Cont.)
Jumpers and Connectors (Cont.)

MIO-5373 Startup Manual 3
J1: ATX/AT Mode Selection
Function Jumper Setting
AT Mode (Default)
ATX Mode
Pin SignalPinDenition
1 AT_DET#
2 GND
J2: RI# 5V/12V selection pin for CN9
Function Jumper Setting
COM(CN9) voltage setting:
+V5
COM(CN9) voltage setting:
+V12
Panel Voltage Setting: RI#
(Default)
Pin SignalPinDenition
1 +V5
2 CN9_RI#
3 COM_RI#
4 CN9_RI#
5 +V12
6 CN9_RI#
J3: Panel Voltage Selection
Function Jumper Setting
Panel Voltage Setting:
+V3.3(Defualt)
Panel Voltage Setting:
+V5
Panel Voltage Setting:
+V12
Pin SignalPinDenition
1 +V3.3
2 NC
3 +V_CH7511B_LCD
4 +V12
5 +V5
6 NC
Jumpers and Connectors (Cont.)

4 MIO-5373 Startup Manual
J4: LVDS JEIDA and VESA mode Selection
Function Jumper Setting
JEIDA mode Setting:
+V3.3
VESA mode Setting:
GND (Default)
Pin SignalPinDenition
1 LVDS1_VCON
2 LVDS1_VCC
3 GND
4 NC
SW1: Clear CMOS
Function Jumper Setting
Keep COMS Data
(Default)
Clear CMOS Date
Pin SignalPinDenition
1 RTC_a_RST#
2 RTC_RST#
3 GND
Caution! The computer is provided with a battery-powered
real-time clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
Jumpers and Connectors (Cont.) Caution

MIO-5373 Startup Manual 5
Figure 1: MIO-5373 Connector Locations (Top Side)
Figure 2: MIO-5373 Connector Locations (Bottom Side)
Figure 3: MIO-5373 Connector Locations (Coastline)
Connector Locations
CN8
CN11
CN23
CN29
CN15
CN9
CN2
CN27 CN12
CN1
CN13
CN22 CN32
CN37
CN31
CN36
CN24
CN10
CN30
CN28
CN30
CN26
CN25
J1
CN3
J2 J3
J4
CN30A1
CN17
CN16
CN14 CN5
CN20

6 MIO-5373 Startup Manual
Mechanical Drawing
Figure 4: MIO-5373 Mechanical Drawing (Top Side)
Figure 5: MIO-5373 Mechanical Drawing (Bottom Side)
Figure 6: MIO-5373 Mechanical Drawing (Coastline)
H
G
F
E
D
C
B
A
15
4
3
2
811
10
9
7
6
APPEARANCE
PART
INTERIOR
PART
FILE NAME
P/N ADDED CODE
MODEL NAME
0.20
D
0.20
P1
0.05
2019/10/3
2019/10/3
REV.
SIZE UNITS
mm
SHEET
2 Of 3
A2
APPROVED
DESIGNER
CHECKED
DRAWER
SCALE
PART NO.
D
THIRD ANGLE
PROJECTION
0.25
0.30
0.40
0.60
D=3L/1000
0.50
0.20
FINISHING
MATERIAL
(Max)
S2
S1
M2
0.10
0.40
L
0.70
0.40
0.15
0.25
0.20
0.30
0.25
0.50
0.80
1.0
0.50 0.35 0.60
1.10
0.25
0.30
0.45
0.20
0.10 0.15
M1
DIMENSIONAL
TOLERANCES
0.10
0.15
0.15
0.30
0.20
ANGLE
6~29.99
30~79.99
80~179.99
180~314.99
315~800
0.05 0~5.99
90
Other 1.5
0.60
1.00
P2
0.15
0.10
0.40
0.50
DESCRIPTION/PART NAME
2019/10/3
TOLERANCES
H
G
F
E
D
6
5
4
3
2
1

MIO-5373 Startup Manual 7
Figure 7: MIO-5373 Mechanical Drawing (with Heatsink)
1. There is a Heatsink in the white box, please take it and remove the release paper from the thermal pads.
2. There are eight screws, six studs and two nuts inside the white box, please install the heatsink into place as per illustration
and assembly sequence below:
1 5 3
4 2 6
Mechanical Drawing (Cont.)
Quick Installation Guide
Remove Release Paper