Advantech MIC-3357 User manual

MIC-3357
6U-sized
CompactPCI™CompactPCI™
CompactPCI™CompactPCI™
CompactPCI™ Pentium®
MMX SBC with VGA / Triple LAN

Copyright Notice
This document is copyrighted, 2001. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from
its use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
Fast EtherChannel (FEC) is a trademark of Cisco Systems, Inc.
IBM, PS/2, OS/2, and VGA are trademarks of International Business
Machines Corporation.
Intel, Pentium, Celeron, and PRO/100+ are trademarks of Intel Corpora-
tion.
Windows is a registered trademark of Microsoft Corporation.
NetWare is a trademark of Novell, Inc.
Symbios is a trademark of Symbios Logic Corporation.
PICMG™, CompactPCI™ and the PICMG™, and CompactPCI™ logos
are trademarks of the PCI Industrial Computers Manufacturers Group.
All other product names or trademarks are properties of their
respective owners.
CE Notification
The MIC-3357, developed by Advantech CO., LTD., has passed the
CE test for environment specification when shielded cables are used
for external wiring. We recommend the use of shielded cables.
Part No. 2002335700 1st Edition
Printed in Taiwan July 2001

Product warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for
one year from the date of purchase.
This warranty does not apply to any products which have been
repaired or altered by persons other than repair personnel authorized
by Advantech, or which have been subject to misuse, abuse, accident
or improper installation. Advantech assumes no liability under the
terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If
an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service
time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any on-
screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your
manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

Packing List
Before installing your board, ensure that the following materials have
been received:
• One MIC-3357 all-in-one single board computer
• One utility CD-ROM disc
• One 6-pin mini-DIN to PS/2 keyboard and PS/2 mouse cable
• One warranty certificate
• This user's manual
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3385 or any other
Advantech products, please visit our support website at:
• http://support.advantech.com.tw
For more information about Advantech's products and sales informa-
tion, please visit:
• http://www.advantech.com

Contents
Chapter 1 Hardware Configuration ............... 1
1.1 Introduction ........................................................................................... 2
1.2 Features ................................................................................................. 3
1.3 Specifications ........................................................................................ 3
1.3.1 Standard SBC Functions ............................................................... 3
1.3.2 10/100Base-TX Ethernet Interfaces .............................................. 4
1.3.3 PCI VGA Interface ........................................................................ 4
1.3.4 Optional Rear I/O Boards ............................................................. 5
1.3.5 Mechanical and Environmental Specifications .............................. 5
1.4 Function Block Diagram ..................................................................... 6
1.5 Jumpers ................................................................................................. 7
1.5.1 Jumper Locations ......................................................................... 7
1.5.2 COM Mode Selection (JP1 ~ 6) .................................................. 8
1.5.3 PVIO Voltage Setting (JP7) ........................................................... 8
1.5.4 Clear CMOS (JP9) ....................................................................... 9
1.5.5 CompactFlash Master/Slave Selection (JP10) .............................. 9
1.6 Connectors .......................................................................................... 10
1.7 Front Panel Connectors and Indicators ........................................... 12
1.8 Safety Precautions ............................................................................. 13
1.9 Installing SDRAM (SODIMMs) ....................................................... 14
1.10 Card Installation ................................................................................ 15
Chapter 2 Connecting
Peripherals ................................................. 17
2.1 VGA Display Connector (CN1) ......................................................... 18
2.2 Serial Ports (CN2 and CN3) ............................................................. 18
2.3 PS/2 Keyboard and Mouse Connector (CN4) .................................. 18
2.4 Ethernet Connectors (CN5, 6 and 7) ................................................ 19
2.5 USB Connector (CN8) ....................................................................... 19
2.6 Floppy Drive (CN10) .......................................................................... 19
2.7 CompactFlash Interface (CN11) ....................................................... 19
2.8 IDE Device (CN13) ............................................................................. 20

Chapter 3 LAN Configuration ....................... 21
3.1 Introduction ......................................................................................... 22
3.2 Features ............................................................................................... 22
3.3 Driver Installation .............................................................................. 22
3.4 Windows NT Drivers Setup Procedure ............................................ 25
3.5 Windows 2000 Drivers Setup Procedure .......................................... 34
Chapter 4 PCI SVGA Setup ........................... 41
4.1 Introduction ......................................................................................... 42
4.2 Installation of SVGA Driver ............................................................. 42
4.3 Installation for Windows NT 4.0 ....................................................... 43
Chapter 5 Award BIOS Setup ....................... 47
5.1 AWARD BIOS Setup .......................................................................... 48
5.1.1 Entering Setup ............................................................................. 48
5.1.2 Standard CMOS Setup ................................................................ 49
5.1.3 BIOS Features Setup ................................................................... 49
5.1.4 Chipset Features Setup ............................................................... 53
5.1.5 Power Management Setup .......................................................... 53
5.1.6 PNP/PCI Configuration Setup .................................................... 54
5.1.7 Load BIOS Defaults .................................................................... 54
5.1.8 Load Setup Defaults .................................................................... 55
5.1.9 Integrated Peripherals .................................................................. 55
5.1.10 Password Setting ....................................................................... 55
5.1.11 IDE HDD Auto Detection ........................................................ 55
5.1.12 Save & Exit Setup ...................................................................... 56
5.1.13 Exit Without Saving ................................................................... 56
Appendix A Programming the
Watchdog Timer......................................... 57
A.1 Programming the Watchdog Timer .................................................. 58
Appendix B Pin Assignments ....................... 61
B.1 VGA Display Connector (CN1) ......................................................... 62
B.2 COM1 and COM2 Serial Ports (CN2 and CN3) ............................ 62
B.3 Keyboard and Mouse Connnector (CN4) ........................................ 63
B.4 Ethernet RJ-45 Connectors (CN5 ~ 7) ............................................. 63
B.5 USB Connector (CN8) ....................................................................... 64
B.6 Floppy Drive Connector (CN10) ....................................................... 65

B.7 CompactFlash Socket (CN11) ........................................................... 66
B.8 IDE Connector (CN13) ....................................................................... 67
B.9 System I/O Ports ................................................................................. 68
B.10 DMA Channel Assignments ............................................................. 68
B.11 Interrupt Assignments ....................................................................... 69
B.12 J1 connector pin assignments ........................................................... 70
B.13 J2 connector pin assignments ........................................................... 71
B.14 J3 connector pin assignments ........................................................... 72
B.15 J4 connector pin assignments ........................................................... 73
Figures
Figure 1-1: MIC-3357 function block diagram .............................................................. 6
Figure 1-2: MIC-3357 Jumper Setting .......................................................................... 8
Figure 1-3: MIC-3357 connector and jumper locations .............................................. 11
Figure 1-4: MIC-3357 Front Panel Connector and Indicator Locations ..................... 12
Figure 1-5: Installing the card into the chassis ............................................................. 16
Figure 5-1: Setup program initial screen ..................................................................... 48
Figure 5-2: CMOS Setup Screen ................................................................................. 49
Figure 5-3: BIOS features setup screen ...................................................................... 49
Figure 5-4: Chipset features setup screen .................................................................. 53
Figure 5-5: Power management setup screen .............................................................. 53
Figure 5-6: PCI configuration screen .......................................................................... 54
Figure 5-7: Integrated peripherals ............................................................................... 55

Tables
Table 1-1: MIC-3357 jumper descriptions .................................................................... 7
Table 1-2: PVIO voltage setting (JP7) ........................................................................... 8
Table 1-3: Clear CMOS (JP9) ....................................................................................... 9
Table 1-4: CompactFlash Master/Slave Selection (JP10) .............................................. 9
Table 1-5: MIC-3357 connector descriptions ............................................................. 10
Table 2-1: MIC-3357 serial port default settings ........................................................ 18
Table B-1: MIC-3357 CRT display connector ............................................................ 62
Table B-2: MIC-3357 COM1 and COM2 serial ports ............................................... 62
Table B-3: MIC-3357 keyboard connector ................................................................. 63
Table B-4: MIC-3357 Ethernet RJ-45 connectors ...................................................... 63
Table B-5: MIC-3357 USB1 connector ....................................................................... 64
Table B-6: Floppy drive connector ............................................................................. 65
Table B-7: MIC-3357 CompactFlash socket .............................................................. 66
Table B-6: MIC-3357 IDE connector .......................................................................... 67
Table B-9: System I/O ports ....................................................................................... 68
Table B-10: DMA channel assignments ...................................................................... 68
Table B-11: Interrupt assignments .............................................................................. 69
Table B-12: J1 connector pin assignments .................................................................. 70
Table B-13: J2 connector pin assignments .................................................................. 71
Table B-14: J3 connector pin assignments .................................................................. 72
Table B-15: J4 connector pin assignments .................................................................. 73

1
Hardware
Configuration
CHAPTER

2MIC-3357 User's Manual
1.1 Introduction
The MIC-3357 is a 6U CompactPCI™ single board computer. With an
on-board Intel® Pentium® MMX 266 MHz CPU, the MIC-3357 can
operate under a wider operating temperature range. The MIC-3357 has
many functions within a merely single-slot width, thus saving valuable
CompactPCI™ slots for peripheral boards.
Low-Powered Mobile Pentium® Processor
The MIC-3357 uses an embedded Intel® Pentium® MMX 266 MHz
processor, which has low power consumption and an extended
temperature range. This CPU is designed for embedded application
and is suitable under fanless operation.
Complete I/O Functions
The MIC-3357 offers all the functions of an industrial computer with
the rugged Eurocard form factor. It offers a PCI VGA display, two serial
ports, one USB port, three auto-switchable fast Ethernet interfaces,
and one PS/2 keyboard/mouse connector. Standard connectors for all
the functions are available on the front and rear panels. The front
panel also has LEDs for power status, HDD operation and Ethernet
communication, as well as a reset button.
The built-in high speed PCI IDE controller provides one IDE channel
with Ultra DMA/33 mode. The User-defined J3 connector is designed
to support up to two IDE devices and two FDDs. These drives can
simply be connected to the backplane or to the rear transition board
for easy service and maintenance.
Meets Industrial Application Requirements
The MIC-3357 is designed for use in mission critical applications. It
accepts a CompactFlash™ memory card on the board or on the rear
transition board, to eliminate the need to use a fragile rotating hard
drive. To protect the system, a watchdog timer can automatically reset
the system if the system stops due to a program bug or EMI. The two-
layer front panel design complies with IEEE 1101.10. Connectors are
firmly screwed to the front panel, and the replaceable shielding gasket
is attached to the panel edge. This reduces emissions and gives better
protection against external interference.

Chapter 1 Hardware Configuration 3
1.2 Features
• On-board Intel® Pentium® 266 CPU
• Intel® 430TX chipset
• Two SO-DIMM sockets support up to 256 MB SDRAM
• One PCI-to-PCI bridge drives up to 7 CompactPCI™ slots
• Three on-board 10/100Base-TX fast Ethernet with RJ-45 connectors
• On-board high-performance VGA display
• Connection to two Ultra DMA/33 high speed IDE devices through
J3 connector
• Accepts CompactFlash™ memory card on-board (optional)
Compact single slot wide
1.3 Specifications
1.3.1 Standard SBC Functions
•CPU: On-board Intel® Pentium® MMX 266 MHz CPU
•BIOS: Award 2 Mb flash memory
•Chipset: Intel® 430TX chipset
•Front Side Bus Clock: 66 MHz
•Bus Interface: 32-bit/33 MHz, PICMG 2.0 compliant
•2nd level cache: 256 KB on-board
•RAM: Two 144-pin SO-DIMM sockets. Support up to 256 MB
SDRAM.
•Enhanced IDE interface: Handles up to two IDE devices.
Supports PIO mode 4, DMA/33 mode.
•Floppy disk drive interface: Supports up to two floppy disk drives
•Series ports: Two RS-232 ports with 16C550 compatible UARTs

4MIC-3357 User's Manual
•USB interface: One USB connector with fuse protection. Complies
with USB specification 1.0
•Keyboard/Mouse connectors: One 6-pin mini-DIN connector on the
front panel.
•Watchdog timer: Can generate a system reset. Software enabled/
disabled. Time interval is from 1 to 63 seconds, jumperless with run-
time setup.
•PCI-to-PCI bridge: One Intel® DEC 21150 controller chip, drives up
to 7 PCI master peripherals
1.3.2 10/100Base-TX Ethernet Interfaces
!Controller chips: Three Realtek 8139C Fast Ethernet controller chips
!10 Mbps or 100 Mbps auto-switchable
!Three LAN ports on the front panel
1.3.3 PCI VGA Interface
!Controller: Intel® C&T 69000
!PCI 2.1 compliant, 33 MHz
!Display memory: On-chip 2 MB SDRAM
!Display resolution:
noituloseRsroloCforebmuN
4201X0821,867X4201,006X008,084X046)stib8(652
867X4201,006x008,084x046)stib61(635,56
006X008,084X046)stib42(noillim8.61
084X046)stib23(noillib3.4

Chapter 1 Hardware Configuration 5
1.3.4 Optional Rear I/O Boards
emaNsledoM&BK2/SP
esuom
MOC
stroP
BSU
stroP
NAL
stroP
AGV
.nnoC
ISCS
.nnoC
EDI
.nnoC
DDF
.nnoC
hsalFtcapmoC
tekcoS
htdiWtolS
2033-CIMV112VV2VV1
F2033-CIMV222VV2VV2
Note: The MIC-3357 does not support SCSI function.
1.3.5 Mechanical and Environmental Specifications
!Operating temperature: 0 ~ 60°C (32 ~ 140°F), depending on CPU
installed
!Storage Temperature: -20 ~ 80°C (-4 ~ 176°F)
!Humidity (Operating and storage): 5 ~ 95% (non-condensing)
!Power Consumption: +5 V @ 1.6 A; +3.3 V @ 1.2 mA; +12 V @ 4
mA;
!Board size: 233.35 x 160 mm (6U size), 1-slot (4 TE) wide
!Weight: 0.8 Kg (1.8 lb)
!Shock: 20 G (operating); 50 G (storage/transit)
!Random vibration: 1.5 Grms

6MIC-3357 User's Manual
1.4 Function Block Diagram
Figure 1-1: MIC-3357 function block diagram

Chapter 1 Hardware Configuration 7
1.5 Jumpers
1.5.1 Jumper Locations
The MIC-3357 provides jumpers for configuring your board for
specific applications other than the default settings.
Table 1-1 list the jumper functions. Figure 1-2 illustrates the jumper
locations.
Table 1-1: MIC-3357 jumper descriptions
Number Function
JP1~6 COM mode selection
JP7 PVIO voltage selection
JP8 SVIO voltage selection (available in the future)
JP9 Clear CMOS
JP10 (optional) CompactFlash card master/slave selection

8MIC-3357 User's Manual
Figure 1-2: MIC-3357 Jumper Setting
1.5.2 COM Mode Selection (JP1 ~ 6)
The MIC-3357 offers two serial ports in micro-formats: COM1 and
COM2. These ports accept RS-232, 422 and 485, and can be selected
by using the jumper setting (Please refer to figure 1-2.) For more
information, you may also refer to section 2.2.
1.5.3 PVIO Voltage Setting (JP7)
The jumper JP7 is used to select the PCI bus reference voltage before
the PCI-to-PCI bridge (PVIO). The MIC-3357 allows PVIO to be set to
either 5 V or 3.3 V. The default is configured as 3.3 V. If the different
voltage is needed, please refer to the following table for changing the
PVIO voltage.
Table 1-2: PVIO voltage setting (JP7)
Voltage PVIO
3.3 V (Default)
5 V

Chapter 1 Hardware Configuration 9
1.5.4 Clear CMOS (JP9)
This jumper is used to erase CMOS data and reset system BIOS
information. Follow the procedures below to clear the CMOS.
1. Turn off the system.
2. Close jumper JP9 (2-3) for about 3 seconds.
3. Close jumper JP9 (1-2).
4. Turn on the system. The BIOS is reset to its default setting.
Table 1-3: Clear CMOS (JP9)
CMOS JP9
Clear
Normal (default)
1.5.5 CompactFlash Master/Slave Selection (JP10)
The MIC-3357 accepts on IDE-compatible CompactFlash memo-
ry card is optional based on an OEM demand. Once a Compact-
Flash socket in added on the MIC-3357 board, please set the
CompactFlash memory as the master or the slave depending on
your need. The default is configured as the slave.
Table 1-4: CompactFlash Master/Slave selection (JP10)
Priority JP10
Master
Slave (default)
123

10 MIC-3357 User's Manual
1.6 Connectors
On board connectors link to external devices such as hard disk drives,
keyboards, or floppy drives, etc. Table 1-5 lists the function of each
connector and Figure 1-3 and Figure 1-4 illustrate each connector
location. Chapter 2 gives instructions for connecting external devices
to your card.
Table 1-5: MIC-3357 connector descriptions
Number Function
CN1 VGA connector
CN2 COM1 connector
CN3 COM2 connector
CN4 PS/2 Keyboard and mouse connector
CN5 Ethernet connector 1
CN6 Ethernet connector 2
CN7 Ethernet connector 3
CN8 USB connector
CN10 FDD connector
CN11 CompactFlash socket (optional)
CN13 IDE connector
J1/J2 Primary CompactPCI bus
J3/J4 Rear I/O transition
LED1 HDD LED and Power LED
SW1 Reset switch
Please refer to Appendix B for pin assignments.

Chapter 1 Hardware Configuration 11
Figure 1-3: MIC-3357 connector and jumper locations

12 MIC-3357 User's Manual
Figure 1-4: MIC-3357 Front Panel Connector and Indicator Locations
1.7 Front Panel Connectors and Indicators
LAN3LAN2LAN1
USB
COM2
COM1
VGA
RESET
PWRHDD