Advantech PPC-103 User manual

PPC-103
Celeron®/Pentium™III Panel PC
with 10.4" LCD flat panel display

ii
Copyright Notice
This document is copyrighted 2000 by Advantech Co. Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of Advantech. Information provided in this manual is intended
to be accurate and reliable. However, Advantech assumes no responsibility
for its use, nor for any infringements upon the rights of third parties which
may result from its use.
All brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders.
PartNo.2002010300, 1stEdition
Printed in Taiwan
December2000

iii
FCC Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio
frequency energy. If not installed and used in accordance with this
user's manual, it may cause harmful interference to radio communica-
tions. Note that even when this equipment is installed and used in
accordance with this user’s manual, there is still no guarantee that
interference will not occur. If this equipment is believed to be causeing
harmful interference to radio or television reception, this can be
determined by turning the equipment on and off. If the interference is
occurring, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning: Any changes or modifications made to the equipment
which are not expressly approved by the relevant stan
dards authority could void your authority to operate the
equipment.

iv
Packing List
Before installing your panel PC, ensure that the following materials
have been received:
• PPC-103seriespanel PC
• User's manual
• Accessories for PPC-103
- Powercable for both FDDand HDD/CD-ROM
- FDDflatcable(35cm)
- Keyboardextension cable (5-pin DIN female to 6-pinPS/2 male)
- FDDpower cable
- HDDflatcable(44-pin)(5cm)
- IDE flatcable(40-pin)(46cm)
- Audio line-in cable
- Power cord (1.8 m) - USA type
- Mounting kits and packet of screws
- Heat sink
- HDDbracket
- Driver/UtilityCD-ROMdisk
- Screws
- Silicon heat sink paste
- CPU push cover
- CPU push screw driver
- Warranty card
- CPUtop plate for FPCGA type CPU
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Note:
1. Customers may buy the CPU separately. Do not buy a CPU that
already has a fan attached with adhesive, because it is not easy to
remove such fan.
If you install or upgrade a CPU yourself, you must install the heat sink
assembly from Advantech above the CPU in order to avoid heat
damage to the CPU. The CPU and the heat sink are normally sold

v
Additional Information and Assistance
1. Visit the Advantech Web site at www.advantech.comwhereyou can
find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's
customer service center for technical support if you need additional
assistance. Please have the following information ready:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version,
application software, etc.)
• A complete description of the problem
• The exact wording of any error messages
together with the fan attached to the CPU. Due to tight constraints
within the PPC-103’s housing, care must be taken to use the heat sink
in the accessory box which will both cool the CPU and fit within the
PPC-103. Thus you must buy a CPU without a fan attached.

vi
Safety Instructions
1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from any AC outlet before cleaning. Do not use
liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the socket-outlet must be installed near the equipment
and must be easily accessible.
5. Please keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it
fallcouldcausedamage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This could cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened
only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to
the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW
-20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
equal to or less than 70 dB(A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

vii
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden
Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein ange-
feuchtetes Tuch zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein
Kippen oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht
abgedeckt werden.
8. Beachten Sie beim AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es
vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine
Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüs-
sigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elek-
trischen Schlag auslösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu tren-
nen und von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni
ert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70
dB(A) oder weiger.
DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

viii
Contents
Chapter 1 General Information....................... 1
1.1 Introduction ................................................ 2
1.2 Specifications............................................. 3
1.3 General ........................................................ 3
1.4 Interface Standard PC functions ............. 3
1.5 I/O Arrangement ......................................... 8
1.6Cutout (Suggestion) ................................... 9
1.7Mounting .................................................... 10
1.7.1 Panel mounting .....................................................................10
1.7.2 Desktop stand (optional)........................................................ 11
1.7.3 Wall-mounting (optional) ...................................................... 12
Chapter 2 System Setup ............................... 13
2.1General....................................................... 14
2.2Removing Rear Panel ............................... 15
2.3 Installing Options..................................... 16
2.3.1 Installing CPU and heat sink assembly................................. 16
2.3.2 Installing a primary 2.5” HDD (internal) ................................19
2.3.3 Installing the SDRAM Memory Module .................................24
2.3.4 Installing an FDD ....................................................................26
2.4 Installing I/O Equipment .........................26
2.4.1 Installing one secondary HDD/CD-ROM device (external)..26
2.4.3 Parallel port connection .......................................................27
2.4.4 PS/2 keyboard and PS/2 mouse ...........................................27
2.4.5 Mic-in, line-out .......................................................................28
2.4.6 External VGA .........................................................................29
2.4.7 Four serial COM ports............................................................29
2.4.8 Ethernet ..................................................................................29

ix
2.5 Installing Software to the HDD ............... 30
2.5.1 Method 1: Use the Ethernet....................................................30
2.5.2 Method 2: Use an FDD ............................................................30
2.5.3 Method 3: Use the COM or parallel port ...............................30
2.5.4 Method 4: Use a 3.5" HDD or CD-ROM ...................................30
2.6 Exploded Diagram ................................... 31
2.7 PCM-9573 and I/O Adapter
Replacement ................................................... 33
2.8 Power Supply and Cooling Fan Replace-
ment............................................................. 34
Chapter 3 Jumper Settings
and Connectors............................................ 37
3.1 Jumpers and Connectors....................... 38
3.1.1 Setting jumpers.......................................................................38
3.1.2 Jumpers and switch................................................................39
3.1.3 Locating jumpers and switch.................................................40
3.1.4Connectors ..............................................................................41
3.1.5 Locating connectors ...............................................................42
3.3 CMOS Clear for External RTC (JP7)...... 43
3.4 COM-port Interface .................................. 43
3.4.1 COM2 RS-232/422/485 setting (JP2, JP3, JP4) .......................43
3.4.2 COM3 / COM4 pin 9 output type setting (JP5) .......................45
3.5VGA Interface............................................. 45
3.5.1 LCD panel power setting........................................................45
3.5.2 Panel type select (SW1) .........................................................45
3.6 Watchdog Timer Configuration.............. 46
3.6.1 Watchdog activity selection (JP6) .........................................46
Chapter 4 Award BIOS Setup ....................... 47
4.1 Award BIOS Setup ................................... 48

x
4.2 CMOS Setup Utility................................... 48
4.3 Standard CMOS Setup ............................ 49
4.3.1 Hard disk configurations ........................................................ 49
4.4 BIOS Features Setup ............................... 51
4.5 Chipset Features Setup .......................... 54
4.6 Power Management Setup ..................... 57
4.7 PNP/PCI Configuration Setup................. 59
4.8 Load BIOS Defaults .................................60
4.9 Load Setup Defaults ................................ 61
4.10 Integrated Peripherals .......................... 61
4.11 Password Setting................................... 63
4.12 IDE HDD Auto Detection........................ 64
4.13 Save and Exit Setup .............................. 65
4.14 Exit Without Saving................................ 65
CHAPTER 5 PCI Bus Ethernet Interface...... 67
5.1 Introduction .............................................. 68
5.2 Installation of Ethernet Driver ................ 68
5.2.1 Installation for Windows 95 ................................................... 69
5.2.2 Installation for Windows 98 ................................................... 72
5.2.3 Installation for Windows NT...................................................76
5.3Further Information .................................. 78
Chapter 6 PCI SVGA Setup ........................... 79
6.1 Introduction .............................................. 80
6.1.1 Chipset.....................................................................................80
6.1.2 Display memory ......................................................................80
6.1.3 Display types ........................................................................... 80
6.2 Installation of SVGA Driver ..................... 80