Advantech POC-W152 User manual

User Manual
POC-W152/W152C
Point- of-Care Terminal with
Intel® Core™ Haswell / Intel®
J1900 Processor and a 15.6’’ VA
LCD (Computer)

POC-W152/W152C User Manual ii
Instructions for the User
The document provides a comprehensive overview of the system. The information is
presented as a sequential series of actions, allowing the user to learn directly how to
use the device. The text provides explanations and instructs the user step-by-step in
the practical use of the product, with short, clear instructions in an easy-to-follow
sequence.
Definitions
Safety Instructions
1. Strictly follow these Instructions for Use; please read these safety instructions
carefully.
2. Please keep this User Manual for later reference; any use of the product
requires full understanding and strict observation of all portions of these instruc-
tions. Observe all WARNINGS and CAUTIONS as rendered throughout this
manual and on labels on the equipment.
3. Repair of the device may only be carried out by trained service personnel.
Advantech recommends that a service contract be obtained with Advantech
Service and that all repairs also be carried out by them. Otherwise the correct
functioning of the device may be compromised.
4. If one of the following situations arises, have the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
Part No. 2008W15200 Edition 1
Printed in Taiwan October 2015
Warning! A WARNING statement provides important information about a poten-
tially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution! A CAUTION statement provides important information about a poten-
tially hazardous situation which, if not avoided, may result in minor or
moderate injury to the user or patient or in damage to the equipment or
other property.
Note! A NOTE provides additional information intended to avoid inconve-
niences during operation.
Warning! Because of the danger of electric shock, never remove the cover of a
device while it is in operation or connected to a power outlet.

iii POC-W152/W152C User Manual
The equipment does not work well, or you cannot get it to work according to
the user manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
5. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning and keep this equip-
ment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage. For plug-in equipment, the power outlet socket must
be located near the equipment and must be easily accessible.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet. Position the power cord so that people cannot
step on it. Do not place anything over the power cord. If the equipment is not
used for a long time, disconnect it from the power source to avoid damage by
transient over voltage.
8. If your computer does not keep the correct time or the BIOS configuration has
been reset to default, the battery may have no charge.
9. Improper installation of VESA mounting can result in serious personal injury!
VESA mount installation should be operated by professional technician, please
contact the service technician or your retailer if you need this service. The detail
operating procedure is specified in Appendix A.
Caution! To avoid short-circuiting and otherwise damaging the device, do not
allow fluids to come in contact with the device. If fluids are accidentally
spilled on the equipment, remove the affected unit from service as soon
as possible and contact the service personnel to verify that patient
safety is not compromised.
Caution! To prevent overheating, do not cover the openings or place the device in
direct sunlight or near radiant heaters.
Caution! Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20° C (-4° F) or above 60° C (140° F).
This may damage the equipment.
Caution! Do not replace battery yourself. Please contact a qualified technician or
your retailer.
The computer is provided with a battery-powered, real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Caution! The battery charging indicator is not included with this device. It will be
added to the finished system assembly and be shown with the com-
pleted system.

POC-W152/W152C User Manual iv
10. Classification:
1). Supply Class I adapter
2). No applied part
3). IPX1
4). Continuous Operation
5). Not AP or APG category
11. Environmental protection: follow national requirements to dispose of unit.
12. Maintenance: to properly maintain and clean the surfaces, use only the
approved products or clean with a dry applicator.
13. Make sure the user does not allow contact between SIP/SOPs and the patient
at the same time.
14. When networking with electrical devices, the operator is responsible for ensur-
ing that the resulting system meets the requirements set forth by the following
standards:
–EN 60601-1 (IEC 60601-1)
Medical electrical equipment
Part 1: General requirements for safety
–EN 60601-1-1 (IEC 60601-1-1)
Medical electrical equipment
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for Medical electrical systems
–EN 60601-1-2 (IEC 60601-1-2)
Medical electrical equipment
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compatibility; Requirements and tests
15. Accessory equipment connected to analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part
or signal output part is configuring a medical system, and is therefore, responsi-
ble that the system complies with the requirements of the system standard IEC
Warning! This device is not suitable for use in the presence of flammable anes-
thetic mixture with air, oxygen, nitrous oxide, or for life support systems.
Caution! When servicing the device, always use replacement parts that are quali-
fied to Advantech standards. Advantech Digital Healthcare cannot war-
rant or endorse the safe performance of third-party replacement parts
for use with our medical device.

v POC-W152/W152C User Manual
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment out-
side of the patient environment. If in doubt, consult the technical services
department or your local representative.
16. Grounding reliability can only be achieved when the equipment is connected to
an equivalent receptacle marked "Hospital Only" or "Hospital Grade".
17. Use a power cord that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular country.
18. “WARNING - Do not modify this equipment without authorization of the manu-
facturer.”
19. “WARNING – To avoid risk of electric shock, this equipment must only be con-
nected to a supply mains with protective earth.
20. “CAUTION: This adapter Sinpro Power: Type: HPU101-107 is a forming part of
the medical device”.
Explanation of Graphical Symbols
Caution! Use suitable mounting apparatus to avoid risk of injury.
Note! Environmental protection
Follow national requirements to dispose of unit.
IEC 60878 and ISO 3864-B.3.6 : Warning: dangerous voltage
ISO 7000-0434 : Caution, consult ACCOMPANYING DOCUMENTS.
ISO 7000-1641 : Follow operating instructions or consult instructions for
use.
IEC 60417 -5009 : STAND-BY.
IEC 60417-5031 : Direct current.
IEC 60417-5021 : Equipotentiality.

POC-W152/W152C User Manual vi
Disposing of Old Products
Within the European Union
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential environment. This equipment
generates, uses and can radiate radio frequency energy. If not installed and used in
accordance with this user manual, it may cause harmful interference to radio commu-
nications.
Note that even when this equipment is installed and used in accordance with this
user manual, there is still no guarantee that interference will not occur. If this equip-
ment is believed to be causing harmful interference to radio or television reception,
this can be determined by turning the equipment on and off. If interference is occur-
ring, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to a power outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
EU-wide legislation, as implemented in each member state,
requires that waste electrical and electronic products carrying the
mark shown at left must be disposed of separately from normal
household waste. This includes monitors and electrical accesso-
ries, such as signal cables or power cords. When you need to dis-
pose of your display products, please follow the guidance of your
local authority, or ask the shop where you purchased the product, or
if applicable, follow any agreements made between you and the
provider.
The mark on electrical and electronic products only applies to the
current European Union Member States.
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standard’s authority could void your
authority to operate the equipment.

vii POC-W152/W152C User Manual
List of Accessories
Before installing your Point-of-Care Terminal, ensure that the following materials
have been received:
POC-W152 series Point-of-Care Terminal
Accessories for POC-W152
CD-ROM disc-"Drivers, User's manual and Utilities"
Mounting kits and packet of screws.
VESA mounting note x1
China RoHs note x1
Additional Information and Assistance
Contact your distributor, sales representative, or Advantech's customer service cen-
ter for technical support if you need additional assistance. Please have the following
information ready before you call:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software,
etc.)
A complete description of the problem
The exact wording of any error messages
This equipment is a source of electromagnetic waves. Before use please, make
sure that there are not EMI sensitive devices in its surrounding which may mal-
function therefore.
Environmental protection
Follow national requirements to dispose of unit.
Manufacturer:
Advantech Co., Ltd.
No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei,
Taiwan 114, R.O.C.
TEL: [phone]
Distributed in Europe by:
Advantech Europe GmbH Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: [phone]
Fax: [phone]
Visit the Advantech websites at www.advantech.com or www.advantech.com.tw if
you need more information.
Warning! No user serviceable parts inside; refer servicing to qualified personnel.
Only the accessories indicated on the list of accessories above have
been tested and approved to be used with the device. Accordingly it is
strongly recommended that only these accessories be used in conjunc-
tion with the specific device. Otherwise the correct functioning of the
device may be compromised.

POC-W152/W152C User Manual viii

ix POC-W152/W152C User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.3 Dimensions ............................................................................................... 4
Figure 1.1 Dimensions of the POC-W152/W152C ...................... 4
Figure 1.2 VESA Mounting of the POC-W152/W152C................ 4
Figure 1.3 POC-W152/W152C Front Panel................................. 5
1.3.1 Optional Modules .......................................................................... 5
1.3.2 Cleaning and Disinfecting ............................................................. 5
Chapter 2 System Setup.......................................7
2.1 A Quick Tour of the POC-W152/W152C................................................... 8
2.1.1 Front View..................................................................................... 8
Figure 2.1 Front View of the Point-of-Care Terminal ................... 8
2.1.2 Rear View ..................................................................................... 8
Figure 2.2 Rear view of the Point of Care Terminal..................... 8
Figure 2.3 Rear view of Multi I/O ports ........................................ 9
2.1.3 Bottom view .................................................................................. 9
Figure 2.4 Bottom view ................................................................ 9
2.2 Installation Procedures............................................................................ 10
2.2.1 Connecting the Power Cord........................................................ 10
Figure 2.5 Connecting the power cord....................................... 10
2.2.2 Connecting the Ground Pin......................................................... 10
Figure 2.6 POC-W152/W152C Equipotential Terminal Pin ....... 10
Figure 2.7 Grounding cable with connector ............................... 10
2.3 Running the BIOS Setup Program .......................................................... 11
2.4 Installing System Software...................................................................... 11
2.5 Installing the Drivers................................................................................ 12
Chapter 3 Operation and Safety Information....17
3.1 General Safety Guide.............................................................................. 18
3.2 Protecting Your Optical Drive.................................................................. 18
3.3 Thermal ................................................................................................... 18
3.4 Disconnect the Power ............................................................................. 19
Appendix A Install VESA Mounting ......................21
A.1 Install VESA Mounting ............................................................................ 22

POC-W152/W152C User Manual x

Chapter 1
1General Information

POC-W152/W152C User Manual 2
1.1 Introduction
The POC-W152/W152C is a multimedia Intel® Haswell/Baytrail processor series
designed for mobile computing as a Point-of-Care terminal (POC.) It is a PC-based
system with 15.6’’ wide screen TFT LCD display, single VGA Port, HDMI out, on-
board 10/ 100/1000 PCI-E Ethernet controllers, and LAN ports. It has dual COM
ports, USB 2.0 and 3.0 ports and a 24-bit stereo audio controller. With the 2.5" SATA
interface, the POC-W152/W152C is a user-friendly computer. For system integrators,
this highly integrated multimedia system lets you easily build a Point-of-Care Termi-
nal into your applications. The POC-W152/W152C makes it an ideal and safe point-
of-care solution for patients and hospital practitioners.
The POC-W152/W152C is specially designed to resist spills and water damage, and
ensures dust resistance with its protected LCD and sealed ports. The POC-W152/
W152C is a reliable solution to your application's processing requirements.
Intended use - The POC-W152/W152C is intended to serve as a Point-of-Care ter-
minal (POC) for integration with hospital systems. POC-W152/W152C is designed for
general purpose medical computing in the hospital environment, for data collection
and for dis-playing information.
NOTE: It should not be used as a life-support system.
The latest version of this user manual is available for download from http://sup-
port.advantech.com.tw/support/
1.2 Specifications
Computing System
CPU
POC-W152:
Intel® Core™ i7-4650U Processor
Intel® Core™ i5-4300U Processor
Intel® Core™ i3-4010U Processor
POC-W152C:
Intel® Celeron® J1900 Quad Core 2.0GHz
Memory Up to 16GB DDR3L 1600MHz
Graphics Controller LVDS
Operating System Win 7, Win 8
System Input
Rating Display
Input Voltage +18 VDC,5.55 A.
Display Size 15.6” TFT LCD (16:9)
Type VA
Max Resolution 1366 x 768
Max. Colors 16.7 M colors
(6-bits+A-FRC)
Pixel Pitch (mm) 0.252(H) x 0.252(V)
Viewing Angle 160°/160°
Luminance 300 cd/m2
Backlight LCD
Contrast Ratio 300

3 POC-W152/W152C User Manual
Chapter 1 General Information
Expansion Slot PCIe
1 x PCIe (x4)
PCIe and Battery Pack can switchable for only
one interface.
Storage HDD 1 x 2.5” SATA , Support 5V/12V, Height up to
15mm, Easy installation
IO Port
Serial Ports 1 x RS-232/422/485 serial port
USB Ports 2 x USB 3.0 ports
3 x USB 2.0 ports
HDMI 1 x HDMI
VGA Port 1 x VGA
LAN 1 x Gigabit Ethernet (RJ45 isolation)
Audio 2 x speakers (1 W)
Power Supply
DC Model External Power Adapter
AC/DC adapter (Sinpro Model no.HPU101-107)
Input Voltage 100-240V AC, 47-63Hz, 1.2-0.5A
Output Voltage +18 VDC,5.55 A.
Battery
1x Backup Battery Pack
PCIe and Battery Pack can switchable for only
one interface
Optional Function
WLAN Integrated wireless 802.11 a/b/g/n
Bluetooth Bluetooth 4.0
RFID Passive RFID
Type Res TS
Touch Screen
Light transmission Res. TS 75%
Controller USB surface
Surface Res. AG
Certification UL/TUV/CB, ANSI/AAMI ES60601-1/EN60601-1/IEC60601-1, CE &
FCC Class B certified
Environment
Shock Resistance 20G peak acceleration (11ms duration)
Temperature
0 ~ 40°C(Operating)
-20 ~60°C (Storage)
-20 ~60°C (Transportation)
Humidity
10%-90% @ 40°C (non-condensing)
5 ~90% (non condensing) (Storage)
5 ~90% (Transportation)
Pressure
700-1013 hPa (Operation)
375 mmHg to 760 mmHg (Storage)
375 mmHg to 760 mmHg (Transportation)
Physical
Characteristics
Dimensions
(W x H x D) 405.53mmx274mmx60.82mm
Weight 4.65Kg

POC-W152/W152C User Manual 4
1.3 Dimensions
Dimensions: 405.53 x 274 x 60.82 mm (Unit: mm)
Figure 1.1 Dimensions of the POC-W152/W152C
VESA Mounting: 75 x 75 mm; 100x100 mm
Please use M4x12L (Maxium)screw.
Figure 1.2 VESA Mounting of the POC-W152/W152C
Warning! Use suitable mounting apparatus to avoid risk of injury.
405.53
274
60.82

5 POC-W152/W152C User Manual
Chapter 1 General Information
Figure 1.3 POC-W152/W152C Front Panel
(A) Power
(B) Volume Down/Up
(C) Touchscreen Status Control
(D) Read Light Control
(E) Brightness Decrease / Increase
1.3.1 Optional Modules
WLAN: Integrated wireless 802.11 a/b/g/n.
Bluetooth: Bluetooth 4.0.
Smart card reader: 1x Smart card reader.
RFID: Passive RFID.
1.3.2 Cleaning and Disinfecting
During normal use of the POC (Point-of-Care Terminal) the device may become dirty
and should be regularly cleaned.
Steps:
1. Prepare cleaning water.
2. Wipe the POC with a clean cloth that has been moistened in the pure water.
3. Wipe thoroughly with a clean cloth.
A B C D E
Caution!
 Do not immerse or rinse the POC or its peripherals. If you accidentally
spill liquid on the device, disconnect the unit from the power source. Con-
tact your IT support department regarding the continued safety of the unit
before placing it back in operation-Do not spray cleaning agent on the
chassis.
 Do not use disinfectants that contain phenol.
 Do not autoclave or clean the POC or its peripherals with strong aromatic,
chlorinated, ketone, either, or ether solvents, sharp tools or abrasives.
Never immerse electrical connectors in water or other liquids.

POC-W152/W152C User Manual 6

Chapter 2
2System Setup

POC-W152/W152C User Manual 8
2.1 A Quick Tour of the POC-W152/W152C
Before you start to set up the POC-W152/W152C, take a moment to become familiar
with the locations and purposes of the controls, drives, connections and ports, which
are illustrated in the figures below.
When you place the POC-W152/W152C upright on the desktop, its front panel
appears as shown in Figure 2.1.
2.1.1 Front View
Figure 2.1 Front View of the Point-of-Care Terminal
Front Bezel View
(1) LCD panel will touch screen module
(2) Power symbol w/ indicator light
2.1.2 Rear View
When you turn the Point of Care Terminal around and look at its rear cover, the
sunken I/O section is at the bottom of the panel PC, as shown in Figure 2-2 and
zoom in Figure 2-3. (The I/O section includes various I/O ports, including serial ports,
VGA port, the Ethernet port, USB ports and so on.)
Figure 2.2 Rear view of the Point of Care Terminal
(1)
(2)
(1)

9 POC-W152/W152C User Manual
Chapter 2 System Setup
Figure 2.3 Rear view of Multi I/O ports
2-2 and 2-3 Rear view
(1) VESA mounting 75mmx75mm( VESA screw: 1/4R/S+M4*12L ST Ni)
Please use M4x12L (Maxium) screw.
(2) Ethernet (network) ports labeled TCP/IP (LAN1)
(3) USB1-USB5 ports* (USB2.0X3, USB3.0 X2)
(4) COM serial port
(5) PCIE slot
(6) VGA port
(7) HDMI port
(8) DC-in
2.1.3 Bottom view
Figure 2.4 Bottom view
Bottom View
( 9) Power switch
(10) Equipotential terminal
(11) Add on card bracket PCIe and Battery Pack can switchable for only one
interface
(5) (3) (2)
(8) (6) (4) (7)
Note! Equipotential terminal need link to hospital ground/earth system before
system boot to protect operator and system.
(11) (10) (9)

POC-W152/W152C User Manual 10
2.2 Installation Procedures
2.2.1 Connecting the Power Cord
The POC-W152/W152C can only be powered by a DC power adapter (Sinpro Model
HPU101-107). Be sure to always handle the power cords by holding the plug ends
only.
Follow these procedures in order:
1. Connect the female end of the power adapter to the DC jack of the panel PC.
(See Figure 2.5)
2. Connect the female end of the power cord to the DC power adapter.
3. Connect the 3-pin male plug of the power cord to an electrical outlet.
Figure 2.5 Connecting the power cord
2.2.2 Connecting the Ground Pin
1. System ready and find the Equipotential Terminal on rear side of POC. An Equi-
potential Terminal is provide to optionally connect to a hospital ground/earth
system
Figure 2.6 POC-W152/W152C Equipotential Terminal Pin
2. Prepare the Grounding cable and the other terminal link to hospital ground/earth
system.
Figure 2.7 Grounding cable with connector
3. Grounding cable plug with POC-W152/W152C Equipotential Terminal (See Fig-
ure 2-7).
Equipotential Terminal