EcLine EC-1219 User manual

User Manual
EC-1219
All-in-one Touch POS Terminal

Overview
Thank you for purchasing the EC-1219 all-in-one touch POS terminal, EC-Line is committed
to continuously improve product quality and provide better after-sales service.In order to
take full advantage of our devices, we strongly recommend that you take the time to read
this manual before diving into software solution.
Note: Information in this manual may change without prior notice.
1. Safety Information
Before plug in the electricity, make sure the power voltage are correct; make sure the
the ground of the power outlet is working properly.
Lightning may damage this product. During lightning storms, unplug the network
cable, power cable and any other connections.
Turn off power before connecting any devices (except USB devices) to the terminal.
Do not attempt to open the chassis. You may be hurt by electric shock. For service,
call your place of purchase.
Do not spill liquid on the terminal. Do not place any objects into the ventilation holes
of this product. It may cause short-circuit of the internal components and cause a fire
or electric shock.
After the computer is stored below temperature of 10 °C, please place the machine in
room temperature (10 - 35 °C) in the original packing for at least two hours to allow
the terminal to restore to room temperature before operation. This is to avoid
condensation that might bring electrical damage.
Keep the terminal clean, dry, and away from dust, moisture and direct sunlight.
Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen.
Wipe it clean with a soft terry cloth applied with a mild solution

Do not share the same power outlet with high power electrical appliances keep
distance from high level magnetic interference.
Do not the use sharp pointed objects to work with the touch screen to avoid damage
to the screen.
When the following occurs:
Liquid get inside the POS terminal;
Physical damage accidental;
POS terminal produces a burning smell;
Immediately disconnect the power supply, unplug the power cord, and contact a
qualified service technician.
2. Electromagnetic compatibility statement
FCC NOTICE
This device complies with Part 15 of FCC Rules. Operations are subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
EUROPEAN COMMUNITY (CE) MARK OF CONFORMITY
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. Logic Controls cannot accept
responsibility for any failure to satisfy the protection requirements resulting from a

non-recommended modification of the product. This product has been tested and
found to comply with the limits for Class A Information Technology Equipment
according to CISPR 22 / European Standard EN 55022.The limits for Class A
equipment were derived for commercial and industrial environments to provide
reasonable protection against interference with licensed communication equipment.

Installation Guide
1. Appearances
2. Rear Panel I/O Connectors
At the rear panel of the EC-1219 is a row of external I/O device connectors
Detailed as follows:
COM1,2: DB9 port for connection to serial devices
MIC: Microphone Input
LINE OUT: Stereo phone jack audio output
LAN: RJ-45 Ethernet connection to Giga-bit LAN
USB2.0: Connection to USB 2.0 devices (compatible with USB 1.1 devices)

USB3.0: Connection to USB3.0 devices (compatible with USB 2.0 devices)
VGA: VGA signal output for connection to external monitor
HDMI: Digital image/sound transmission interface
12V DC IN: Connection to 12V DC Power Supply
POWER: ON/OFF

Specification
Model name
EC-1219
Type
12”All In One Touch POS Terminal
Colour
Black
Material
Magaluma
Optional Peripherals
ISO Trick 1/2/3 Magnetic Stripe Reader
2x20 VFD Customer Display
Second Screen(9.7”,12”,15”)
WIFI
Bluetooth
SSD (32G,64G,128G)
Windows OS
Motherboard Part
Main Board
ITX-J1900
CPU
Intel® Celeron® Processor J1900
(2M Cache, up to 2.42 GHz)
BIOS
AMI BIOS
RAM Support
DDR III 1333 2GB, Up to 8GB RAM
Storage
SSD 32G or UP
Network Support
Realtek 8111E Gigabit Ethernet
Audio
Realtek ALC662 HD
Main Display Part
LCD Size
12”LED-LCD

Viewing Angle
left/right ＋60°~ －60°
up/down ＋80°~ －60°
Brightness
280cd /㎡
Resolution
XGA 1024×768 @ 60Hz
Touch Screen
Type
5 wire resistive touch panel
Touch Interface
USB
I/O Ports
I/O port
DC IN*1(2.5)
HDMI*1
POWER BUTTON(Power LED)*1
COM*3(DB 9)
USB2.0*4
LAN*1
USB3.0*2
LINE*1
MIC*1
Operating Temperature
0 ℃to 40℃
Storage Temperature
-20℃to 60℃
SIZE
405*395*245mm
Package: Carton Box with
Foam Packaging
NW:5.1KG
GW:6.2KG
Power Consumption
35W（MAX）

EMC/ Product Safety
FCC Class A / CE Mark / LVD / CCC
OS Support
Windows 7/8 or up
Accessory
Power adaptor, power cable, CD for driver

Setup and Driver Installation
1. Motherboard BIOS settings
The POS terminal has a BIOS (Basic Input Output System) chip on the
motherboard. Every time you start the terminal, the system will first run the
BIOS self-test routine to check the main components of the system to ensure it
is working properly.
The terminal is loaded with default BIOS settings in the factory. Please do not
change the parameters in the BIOS unless necessary.
In the following situations, you need to run the BIOS setup:
1) Error message appears on the screen during the system self-test and
requested to enter BIOS setup.
a) Press F1 to run setup; or
b) Press F2 to load default values and continue
2) If you need to change the factory default settings to customized application
requirements.
a) During system boot, hit DEL key to enter BIOS setup.
b) If the message disappears before you respond to, you can turn off
the machine and restart the computer. You can also press<Ctrl> +
<Alt> + <Del> to restart.
Control keys
<↑> Move up
<↓> Move down

<←> Move left
<→> Move right
<Enter> To select this option
<Esc> To exit the menu or to return to the main menu from the submenu
<+/PU> Increase the value or change selection
<-/PD> Reduce the value or change selection
<F1> Help, only available in the status menu and select templates menu
<F9> To load default settings
<F10> To store settings and exit the CMOS SETUP program
How to enter and leave the COMS interface:
1)Enter the COMS interface
Boot the terminal , Press the key ”Del”enter COMS interface.
2)Leave the COMS interface
Press the key “F9”>>Restore Defaults
Press the key “F10”>>Save configuration and reset
Press the key “ESC”>>Quit without saving
Press the key ”Ctrl”+”Alt”+”Del”>> Quit without saving

2. Touch screen driver installation:
Step 1 : Navigate to the installer directory to find the “setup.exe” file .Double-click
on ”setup exe” to start installation.
Step 2: When installation starts, click [Next] to proceed to the next step.

Step 3: Install action in progress
Step 4: Uncheck “Install PS/2”. Press [Next] to continue installation.

Step 5: Uncheck”install RS232 interface driver”and click [Next] to continue
installation.
Step 6: Select option “NONE”, click [Next] to continue installation.

Step 7: When installing USB touch, please connect the USB controller and USB cable
Step 8: If there are additional touch monitors connected, please check “Support
multi -monitor system”.

Step 9: Select the destination location to install the touch driver. The default path is
“C:\Program Files\eGalaxtouch”. Click [Next] to continue installation.
Step 10: Select the Program Folder to install the utility. The default is “eGalaxtouch”.

Click [Next]to continue installation.
Step 11: Check the option to create a desktop shortcut icon.

After install the driver successfully, identify the USB controller IS installed as shown
below.
Touch function settings

Touch calibration
Touch device line test