AEG BEWS18125BLC User manual

BEWS18125BLC
BEWS18125BLP
Original instructions

2
2
Important!
This appliance is not intended to be used or cleaned by persons with
reduced physical, sensory or mental capabilities, or lack of experience
or knowledge, unless they have been given instructions concerning the
safe use of the appliance by a person legally responsible for their safety.
They should be supervised whilst using the appliance.
Children shall not use, clean or play with this appliance, which when not
in use should be secured out of their reach.
It is essential that you read the instructions in this manual before
assembling, operating and maintaining the product.
Subject to technical modifications.

33
BEWS18125BLC
1
BEWS18125BLP
1
2
6
5
BEWS18125BLC BEWS18125BLP
BEWS18125BLC
BEWS18125BLP
15
14
9
13
10
4
3
11
12
7
8
12
1. On/Off switch
2. Safety lock lever
3. Spindle lock button
4. Grinding wheel
5. Standard outer flange nut
6. Fixtec nut
7. Wheel guard lock lever
8. Half tool-less wheel guard
9. Anti-vibration auxiliary handle
10. Auxiliary handle
11. Handle, insulated gripping surface
12. Dust cover
13. Battery port
14. Toolless cutting guard
15. Wrench

4
4
10
27
8
9
23
16
15
24
25
26
17
18
19
START
STOP
BEWS18125BLC
20
21
22
START
STOP
BEWS18125BLP
6
BEWS18125BLC
7
BEWS18125BLP
12
11
BEWS18125BLC
14
13
BEWS18125BLP

55
10
27
8
9
23
16
15
24
25
26
17
18
19
START
STOP
BEWS18125BLC
20
21
22
START
STOP
BEWS18125BLP
6
BEWS18125BLC
7
BEWS18125BLP
12
11
BEWS18125BLC
14
13
BEWS18125BLP

6
6
BEWS18125BLC
22
2
1 1
1

77
22
2
11
1
BEWS18125BLP

8
8
1. 2.
3. 4.
2
1

99
click
1. 2.
click
3.
2
3
1

10
10
0°
30°
30°
60° 60°
30
°
60
°
30
°
60
°
0
°

11 11
< 6 mm
> 6 mm
2.
1.
3. 4.
5.
BEWS18125BLC
WARNING:
Always check the spindle lock button is fully released before switching on
the tool!
After using the spindle lock to tighten / loosen the abrasive disk, it is
possible that the button may stick in the lock position. Whilst this will not
damage the tool it may cause the tool or battery protection to operate and
remove power to the tool. Turn o the switch, remove the battery then
carefully rock the disk back and forth to release the spindle lock button.
NOTE:
If the battery protection has also activated, simply remove the battery pack
from the tool and replace it, thus resetting the protection.
The flange nut must be
securely tightened before
the machine is started.

12
12
2.
3.
1.
BEWS18125BLC

13 13
2.
1.
3.
4.
BEWS18125BLP
The flange nut must be
securely tightened before
the machine is started.
WARNING:
Always check the spindle lock button is fully released before switching on
the tool!
After using the spindle lock to tighten / loosen the abrasive disk, it is
possible that the button may stick in the lock position. Whilst this will not
damage the tool it may cause the tool or battery protection to operate and
remove power to the tool. Turn o the switch, remove the battery then
carefully rock the disk back and forth to release the spindle lock button.
NOTE:
If the battery protection has also activated, simply remove the battery pack
from the tool and replace it, thus resetting the protection.

14
14
2.1.
3. 4.
BEWS18125BLP

15 15
1.
1.
2.
2.
Remove the battery pack
before starting any work on
the product.

16
16
78-100 %
33-54 %
55-77 %
10-32 %
<10 %

17 17
Start
Stop
BEWS18125BLC

18
18
2.
Start Start
1 A 1 B
StartStop 4.3.
2 A 2 B
Steady Red
2
1
BEWS18125BLC

19 19
Start
Electronic brake
Flashing Red (Overload)
BEWS18125BLC

20
20
Start
Stop
2
1
BEWS18125BLP