Aeroflex RGS-2000NG Parts list manual

RGS-2000NG
TCAS Test Set
Getting Started Manual
EXPORT CONTROL WARNING: This document contains controlled technical data under the jurisdiction
of the Export Administration Regulations (EAR), 15 CFR 730-774. It cannot be transferred to any foreign
third party without the specific prior approval of the U.S. Department of Commerce, Bureau of Industry
and Security (BIS). Violations of these regulations are punishable by fine, imprisonment, or both.
Issue-4

RGS-2000NG Getting Started Manual
Subject to Export Control, see Cover Page for details.
RGS-2000NG
TCAS Test Set
Getting Started Manual
PUBLISHED BY Aeroflex
COPYRIGHT Aeroflex 201
6
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form
or
by any means, electronic, mechanical, photocopying, recording or otherwise without the prior permission of the publisher.
Original March
2015
Issue-2
August 2015
Issue-3
July 2016
Issue-4
October 2016
10200 West York / Wichita, Kansas 67215 U.S.A. / [phone] / FAX [phone]

RGS-2000NG Getting Started Manual
Subject to Export Control, see Cover Page for details.
This manual contains essential information relating to initial use of the
Unit. Aeroflex recommends the operator become familiar with the
Operation Manual contained on the accompanying CD-ROM.
Aeroflex updates Test Set software on a routine basis. As a result, the
examples may show images from earlier software versions. Images are
updated when appropriate.

RGS-2000NG Getting Started Manual
Subject to Export Control, see Cover Page for details.
1
Product Warranty
Refer to http://ats.aeroflex.com/about-us/quality/standard-
hardware-warranty for the Product Warranty information.
Electromagnetic Compatibility
Double shielded and properly terminated external interface
cables must be used with this equipment when interfacing
with the REMOTE Connector.
For continued EMC compliance, all external cables must be
shielded and 3 meters or less in length.
Nomenclature Statement
In this manual, RGS-2000NG, Test Set or Unit refers to the
RGS-2000NG TCAS Test Set.
Declaration of Conformity
The Declaration of Conformity Certificate included with the
Unit should remain with the Unit.
Aeroflex recommends the operator reproduce a copy of the
Declaration of Conformity Certificate to be stored with the
Operation Manual for future reference.
Software Version
Aeroflex updates Test Set software on a routine basis. As a
result, examples may show images from earlier software
versions. Images are updated when appropriate.

RGS-2000NG Getting Started Manual
Subject to Export Control, see Cover Page for details.
2
Precautions
SAFETY FIRST - TO ALL OPERATIONS PERSONNEL
General Conditions of Use
This product is designed and tested to comply with the
requirements of IEC/EN61010-1 ‘Safety requirements for
electrical equipment for measurement, control and laboratory
use’ for Class I portable equipment and is for use in a
pollution degree 2 environment. The equipment is designed
to operate from installation supply Category II.
The RGS-2000NG should be protected from liquids such as
spills, leaks, etc. and precipitation such as rain, snow, etc.
When moving the equipment from a cold to hot environment,
allow the temperature of the equipment to stabilize before the
Unit is connected to an AC power supply to avoid
condensation forming. The equipment must only be operated
within the environmental conditions specified in the product
specifications.
This product is not approved for use in hazardous
atmospheres or medical applications. If the equipment is to
be used in a safety-related application, such as avionics or
military applications, the suitability of the product must be
assessed and approved for use by a competent person.
Refer all servicing of Unit to Qualified Technical Personnel.
PROTECTION PROVIDED BY EQUIPMENT
MAY BE IMPAIRED IF THE TEST SET IS
USED IN A MANNER NOT SPECIFIED BY
THE MANUFACTURER.
Safety Identification in Technical Manual
This manual uses the following terms to draw attention to
possible safety hazards that may exist when operating or
servicing this equipment:
IDENTIFIES CONDITIONS OR ACTIVITIES
THAT, IF IGNORED, CAN RESULT IN
EQUIPMENT OR PROPERTY DAMAGE, E.G.
FIRE.
IDENTIFIES CONDITIONS OR ACTIVITIES
THAT, IF IGNORED, CAN RESULT IN
PERSONAL INJURY OR DEATH.
Safety Symbols in Manuals and on Units
CAUTION: Refer to accompanying documents.
(Symbol refers to specific CAUTIONS
represented on the Unit and clarified in the text.)
Indicates a Toxic hazard.
Indicates item is static sensitive.
AC TERMINAL: Terminal that may supply or be
supplied with AC or alternating voltage.
Indicates a fuse (AC or DC).
HOT SURFACE: This surface may be hot to the
touch.