AETEK H60-044-30-150 User manual

1. Install the PoE switch in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the switch are not blocked.
3. Use CAT5 or 5e UTP/STP cables.
4. AC input (100~240V/AC, 50~60Hz), for a max. consumption of 150W/250W.
H60-044-30-150 Outdoor Pro L2 Managed PoE Switch
H60-044-90-250
H60-084-30-250 Quick Installation Guide
The H60 series is a 4/8 port 10/100/1000BaseT at PoE or PoH/bt switch capable of feeding 15.4/30W or 15.4/30//60/90W
(54V max. per port) power to Power over Ethernet (PoE) devices. It comes with another 2x GbE TP port + 2xGbE SFP port
or 4xGbE SFP port. The switch is capable of a total of 120W/240 Watts PoE power budget.
IMPORTANT:
INTRODUCTION
* 1x PoE switch * 1x Quick Installation Guide * 1x Console cable
* 1x T25 L-wrench, 4x wall anchors
PACKAGE CONTENTS
5.Digital output (relay): ON/OFF Digital input: level 0(Low) -> 0V, level 1(High) -> 12V.
Reset button
Task Method SYS LED Behavior Port Status LED Behavior
Reset Press 2 ~ 7 seconds Blinking Green All LEDs Off.
Restore Defaults Press 7 ~ 12 seconds Blinking Green All LEDS On.
P/N:A625013900G
H60-044-30-150 H60-044-90-250
10/100/1000
RJ45 ports
100/1000
SFP ports
Digital input
Digital output relay
Power1 LED
Power2 LED
DO LED
10/100/1000
RJ45 ports
100/1000
SFP ports
Digital input
48~56VDC Input
Digital output relay
Console port
Power1 LED
Power2 LED
DO LED
Reset button 100~240V/AC
AC on/off Switch
Console portReset button 100~240V/AC
AC on/off Switch
H60-084-30-250
10/100/1000
RJ45 ports
100/1000
SFP ports
Digital input
Digital output relay
Power1 LED
Power2 LED
DO LED
48~56VDC Input
48~56VDC Input
Console portReset button 100~240V/AC
AC on/off Switch

AETEK INC.
10F, No.168, Lien-Cheng Rd., Chung-Ho, New TaipeiCity, 235, Taiwan, R.O.C.
|T:[phone]|W:www.aetektec.com|E:[email protected]om
Copyright © 2021 AETEK INC. All rights reserved.
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
User Name
Password
DEFAULTS
Power LEDs
LED Color State Description
Power1 Green On Powered on correctly.
Off Not receiving power from power1.
Power2 Green On Powered on correctly.
Off Not receiving power from power1.
DO LED
LED Color State Description
System Yellow On DO ON
Off DO OFF
Baud rate 115200
Stop bits 1
Data bits 8
Parity N
Flow control none
Console Port Defaults
Port Status LEDs
LED Color State Description
RJ45 Ports
Up (PoE)
Amber On The port is enabled and supplying power to connected device.
- Off The port has no active connection, or it is not connected to a PoE PD device. Otherwise, the port may
have been disabled through the switch user interface.
RJ45 Ports
Down (LAN)
Green On The port is enabled and established a link to connected device.
- Off The port has no active network connection, or it has no established link to connected device.
Otherwise, the port may have been disabled through the switch user interface.
SFP Ports Green On The port is enabled and established a link to connected device,
Green Blinking
Green Blinking
The port is transmitting/receiving packets.
The port is transmitting/receiving packets.
- Off The port has no active network connection, or it has no established link to connected device.
Otherwise, the port may have been disabled through the switch user interface.
Outdoor PoE switch:
H60-044-30-150
H60-044-90-250
H60-084-30-250
3/4” conduit
M8
AT-100 AT-101
AT-200