AFX MOTORSPORTS DEF060 User manual

THIS PRODUCT IS FOR OFF ROAD USE ONLY
INSTALLATION MANUAL
SHORT FRONT BUMPER WITH WINCH
POLARIS RZR 1000XP/1000XP TURBO S
DEF060
[email protected]

STEEL FRONT BUMPER WITH WINCH
FOR POLARIS RZR 1000XP/100XP TURBO S
THANK YOU!
FOR PURCHASING AT AFX MOTORSPORTS
HOW TO INSTALL
Pieces included:
AFX
Motorsports
products
are
designed
to
best
fit
user’s
ATV/UTV
under
stock
conditions.
Adding,
modifying,
or
fabricating
any
factory
or
aftermarket
parts
will
void
any
warranty
provided
by
AFX
Motorsports
and
is
not
recommended.
AFX
Motorsports
products
could
interfere
with
other
aftermarket
accessories.
If
user
has
aftermarket
products
on
machine,
contact
AFX
Motorsports
to
verify
that
they
will
work
together.
Although
AFX
Motorsports
has
thousands
of
satisfied
customers,
user
should
be
aware
that
installing
bumpers,
rock
sliders,
spare
tire
carriers,
etc.
will
change
the
ride
of
machine
and
may
increase
maintenance
and
part
wear.
Operating
any
off-road
machine
while,
or
after,
consuming
alcohol
and/or
drugs
increases
risk
of
bodily
harm
or
death.
No
warranty
or
representation
is
made
as
to
this
product’s
ability
to
protect
user
from
severe
injury
or
death.
AFX
Motorsports
urges
operators
and
occupants
to
wear
a
helmet
and
appropriate
riding
gear
at
all
times.
By
purchasing
and
installing
AFX
Motorsports
products,
user
agrees
that
should
damages
occur,
AFX
Motorsports
will
not
be
held
responsible
for
loss
of
time,
use,
labor
fees,
replacement
parts,
or
freight
charges.
AFX
Motorsports,
nor
any
3rd
party,
will
not
be
held
responsible
for
any
direct,
indirect,
incidental,
special,
or
consequential
damages
that
result
from
any
product
purchased
from
AFX
Motorsports.
The
total
liability
of
seller
to
user
for
all
damages,
losses,
and
causes
of
action,
if
any,
shall
not
exceed
the
total
purchase
price
paid
for
the
product
that
gave
rise
to
the
claim.
AFX
Motorsports
will
warranty
only
parts
provided
by
AFX
Motorsports.
Any
damage
or
problems
with
OEM
housings,
bearings,
seals,
or
other
manufacturers’
products
will
not
be
covered
by
AFX
Motorsports.
AFX
Motorsports
parts
and
products
are
not
warrantied
if
item
was
not
installed
properly, misused, or modified.
Liability Statement
Tools needed (Not included):
5/32” Allen Key.
7/16” or 14mm Combination Wrench.
(2x) 3/8” Lock Washer
(2x) 3/8” Flat Washer
(2x) 3/8” nuts
(4x) 3/8” x 1” Bolts
(1x) 5/16” Flat Washer
(1x) 5/16” Lock Washer
(4x) 5/16” Security nuts
(5x) 5/16” x 1” Bolts
Hardware “A”
Hardware “B”
Front Bumper

To finish with the installation thighten all the screws and
place the front plastic that was previously removed
* For safety tighten all the screws.
Now you have completed the installation.
*Note: You need to have the winch assembled before
the installation.
*Just in case that the RZR has
this hardware, remove it and
keep it.
1
Tabs
Plastic
Remove the front plastic of the RZR starting by the tabs.
7
2Place the hardware “A” over the front structure of the RZR,
use a 5/16” screw with one flat washer and one lock washer.
(As it is shown in the image).
Flat washer
Lock washer
5/16” screw
Hardware A
Hardware A

3Install the winch to the hardware “B” with the 4 original
screws of the winch (as it is shown in the image).
Original winch
screw
Mount the hardware “B” with the winch previously
installed and use two 3/8 x 1” screws with lock
washer (as it is shown in the image).
4
3/8 x1” screw
Hardware “B”
perpendicular
to the front
structure
Hardware “B”
Winch
Original winch screw
5
6
Place the bumper over the hardware “B” aligning the
4 upper perforations and use four 5/16 x 1” screws with
nut.
5/16x 1” screw5/16x 1” screw
Align the two lower perforation with the structure of the
RZR, place the original hardware that was previously
removed and use two 3/8 x 1” screw with flat washer
and nut.
3/8 x1” screw