AFX MOTORSPORTS SKI064-A User manual

CAN AM MAVERICK 2 SEATER
ALUMINIUM ROCKSLIDERS
INSTALLATION MANUAL
SKI064-A
Finally, put the last rivets on the remaining holes of the
bottom part of the RockSlider.
4
Repeat this steps for the RockSlider of the other side of the
Vehicle.
5
1/8” - 3/16” INCH THICKNESS
Thighten the bolts remaining and enjoy your ride!
6
[email protected]
THIS PRODUCT IS FOR OFF ROAD USE ONLY

KIT OF ALUMINIUM ROCKSLIDERS
FOR CAN AM MAVERICK 2 SEATS 2013-2016
HOW TO MAKE THE INSTALLATION
Pieces included:
Tools needed (Not Included):
Bottom View, Drivers side.
3/16” Aluminium
RockSlider, pilot
side.
*Image shown regards to
standard product (customized
parts may vary).
Fasten the rear
part first
Secondly, the
front part.
(Recommended).
3/16” Aluminium
RockSlider, co-pilot side.
(18x) 3/16” x 1/2” Rivets.
2
1
Remove the screws from the rear and front part of the side
plastic protectors of your Can Am Maverick. For this step,
use a T-40 Torx Screwdriver. Keep the screws and remove
the side plastic protectors of your vehicle.
1
Set the Aluminium RockSlider (Pilot or Co-pilot’s side) in the
vehicle, and fasten it using the original screws and holes of
the side plastic protectors. It is recommended that you
place the bolts on the rear part of the Aluminium RockSlider
and then the front; Do not thight them yet.
2
Using a riveting tool, place the rivets on the bottom part of
the RockSlider in the holes provided. Use a washer for
each rivet (Included). Recommended: First place the 2
rivets of the front holes, (Fig. 1), and then, place 2 rivets on
the rear holes (Fig. 2). This will help to have an easier
installation on the remaining rivets.
3
T-40 Torx Screwdriver.
Rivet Tool.
(18x) 3/16” Flat washer.
THANK YOU!
FOR PURCHASING AT AFX MOTORSPORTS
AFX Motorsports products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory
or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could
interfere with other aftermarket accessories. If user has aftermarket products on machine, contact AFX Motorsports to verify that they
will work together. Although AFX Motorsports has thousands of satisfied customers, user should be aware that installing bumpers, rock
sliders, spare tire carriers, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet
and appropriate riding gear at all times. By purchasing and installing AF1 Motorsports products, user agrees that should damages
occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. AFX
Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that
result from any product purchased from AFX Motorsports. The total liability of seller to user for all damages, losses, and causes of
action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty
only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’
products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warrantied if item was not installed
properly, misused, or modified.
Liability Statement
Hardware:
(2x) 6mm x 30mm screws.