Agilent Technologies U1602B User manual

Agilent Technologies
Agilent
U1602B and U1604B
Handheld Digital
Oscilloscopes
Quick Start Guide

1
Use the product only as specified by the manufacturer.
Do not install substitute parts or perform any
unauthorized modification to the product. Return the
product to Agilent Technologies or a designated repair
center for service to ensure that safety features are
maintained.
The Agilent U1600B Series handheld digital
oscilloscopes comply with the following standards.
• IEC 61010-1:2001 / EN61010-1:2001
• Canada: CSA C22.2 No. 61010-1:2004
• USA: UL 61010-1:2004
Safety Terms and Symbols
A WARNING notice denotes a hazard. It calls
attention to an operating procedure, practice, or the
like that, if not correctly performed or adhered to,
could result in personal injury or death. Do not
proceed beyond a WARNING notice until the
indicated conditions are fully understood and met.
A CAUTION notice denotes a hazard. It calls attention
to operating procedure, practice, or the like that, if not
correctly performed or adhered to, could result in
damage to the product or loss of important data. Do not
proceed beyond a CAUTION notice until the indicated
conditions are fully understood and met.
Symbols
Safety Information
WARNING
CAUTION
Earth Ground Terminal
Risk of electric shock
CAUTION
(refer to safety information in manual)
Equipotentiality
Direct and alternating current
Direct current
Double insulation
Caution, hot surface
CAT III
Measurement Category III

2
Prevention of fire or injury:
• Use only the designated AC adapter and test leads
supplied with the instrument.
• Observe all ratings and markings of the instrument
before connecting to the instrument.
• When performing measurement, ensure that the
right safety and performance ratings of instrument
and accessories are used.
• Connect the scope probe or test leads to
instrument before connecting to any active circuit
for testing. Before disconnecting the active circuit
from instrument, remove scope probe or test leads
from active circuit.
• Do not connect the ground wire to voltages higher
than 42 Vpeak (30 Vrms) from earth ground.
WARNING
Maximum Input Voltages
Maximum Floating Voltage
• From any terminal to ground — 300 Vrms CAT III
(up to 400 Hz)
• Input CH1 and CH2 direct (1:1 Probe) — 300 V CAT III
• Input CH1 and CH2 via 1:10 Probe — 600 V CAT III
• Input CH1 and CH2 via 1:100 Probe — 600 V CAT III
• Meter Input — 300 V CAT III, 600 V CAT II
• Scope Input — 300 V CAT III
• Voltage ratings are Vrms (50 Hz - 60 Hz) for AC sine
wave and VDC for DC applications.
• Do not expose the circuit or operate the instrument
without its cover or while power is being supplied.
• Do not use exposed metal BNC or banana plug
connectors, use only the insulated voltage probes,
test leads and adapters that come with the
instrument.
• Do not supply any voltage when measuring
resistance or capacitance in meter mode.
• Do not operate the instrument if it does not operate
properly, have the instrument inspected by qualified
service personnel.
• Do not operate the instrument in wet or damp
environments.
• Do not operate the instrument in any environment
in a risk of explosion.
• Maintain a clean and dry condition to the
instrument’s surface.
Prevention of electro-static discharge
• Electro-static discharge (ESD) can result in damage
to the components in the instrument and
accessories.
• Select a static-free working location when installing
and removing sensitive components.
• Handle sensitive components to the minimum
extent possible. Do not allow contacts between
components and exposed connector pins.
• Transport and store in ESD preventive bag or
container that protects sensitive components from
static electricity.
Safety Information
CAUTION

3
Table of Contents
Safety Information 1
Introduction 4
The Front Panel at a Glance 4
Getting Started
• To Inspect Package Contents 5
• To Charge a Battery 6
• To Power On the Handheld Scope 6
• To Reset to Factory Default Setting 6
• To Perform Self-Calibration 6
• To Set Time and Date 6
• To Set Auto Power Off 7
• To Select Language for Quick Help 7
• To Adjust Contrast of Display 7
• To Compensate Scope Probe 7
Scope Screen Display 8
Scope Connection Configuration 9
Meter Connection Configuration 10
Cursor Measurement 11
Save/Recall Setup and Waveform 12
Signal Triggering 12
Automatic Measurements 14
Data Logger 14
Quick Help 14
Charging the Battery 15

4
Introduction
This quick start guide provides the basic information, front panel functions
and general specifications of Agilent U1600B Series handheld digital
oscilloscopes. The U1600B Series can also function as a digital multimeter
(DMM) and data logger. With its 4.5- inch LCD color display, it is capable of
clearly distinguishing waveforms from two channels. The U1600B Series
handheld digital oscilloscopes are high performance troubleshooting tools in
multi- industrial automation, process control, facility maintenance and
automotive- service industries. The U1600B Series comprises two models:
U1602B and U1604B, with 20 MHz and 40 MHz bandwidths, respectively. Both
models are dual- channel scopes with real- time sampling rate of up to 200
MSa/s. Users can use the Dual Waveform Math (DWM) and Fast Fourier
Transform (FFT) functions (in U1604B) to perform a quick waveform analysis
in both time and frequency domain. The U1600B Series with built- in 6000-
count resolution and true RMS comes with an auto range function that allows
users to perform quick and accurate DMM measurements. Additionally, with
data logger function, users can perform automatic data logging for all DMM
measurements.
The Front Panel at a Glance
Quick Help button
Power Switch button
Softkeys to select submenu of
each function mode.
Logger mode button
User mode button
Scope mode button
Meter mode button
Auto measurement button
To access Cursor mode, press
and hold the button.
Run/Stop button
To access Save/Recall mode,
press and hold the button
Trigger button
To access Trigger mode, press
and hold the button.
Autoscale button
For manual ranging setting, press
and hold the button.
Horizontal scale
button to
increase and
reduce time/
Vertical scale button to
increase and reduce
volt/div for respective
channel.
Turn clockwise or anti-clockwise
for value selection and press the
knob to set the value.

5
Getting Started
To Inspect Package Contents
Inspect and verify the following items for the standard purchase of
U1602B or U1604B, and any optional accessories you may have
Optional Accessories
1. Soft casing
2. Scope probe (100:1)
CAT III 600 V with
ground alligator clip
Standard Item and
Accessories
1. Handheld digital
oscilloscope
2. Power cable
3. Ni- MH battery pack,
7.2 V
4. AC adapter
5. Two scope probes
(10:1) CAT III 600 V
6. DMM test lead
7. Hook Clip
8. Ground alligator clip
9. Medium jaw alligator
clip
10. USB cable
11. Quick Start Guide
34
5
6
1
2
7
11
12
8
9
10

6
To Charge a Battery
Upon delivery of the unit, the rechargeable
battery is required to be fully charged for
approximately 25 hours with the desig-
nated Agilent AC adapter. Ensure that you
have the correct line power cord. The AC
adapter converts input line voltages rang-
ing from 100 VAC to 240 VAC to output
voltage 12 VDC.
Input: 100 V – 240 VAC
Output: 12 VDC, 2 A,
50/60 Hz
To Power On the Handheld Scope
To turn on or off the scope, press and hold the
power switch button for three seconds. A
basic self-test shall be executed
automatically upon power up. The scope will
be loaded with the last configuration setup of
the scope.
To Reset to Factory Default Setting
To recall the factor default settings:
Open Save/Recall menu by pressing and
holding the button
Open Save/Recall Setup menu
Select MORE 1/4 page menu
Restore factory default settings
Enter for “Restore OK?”
To Perform Self-Calibration
To ensure the scope is operating properly,
perform the self- calibration. Before pro-
ceeding to the next step, ensure the scope
passes self- calibration.
Open User menu
Open Utility menu
Select MORE 3/4 page menu
Self-calibration start
Disconnect all probe and meter
connections to the input terminal
before starting self- calibration.
To Set Time and Date
User Open User menu
Open Utility menu
Select MORE 2/4 page menu
Select time format in MM/DD/YY or
YY/MM/DD
Select time set for Year, Month, Day, Hour,
Minute or Second
Turn rotary switch to set the time display
To Set Auto Power Off
User Open User menu
Open Utility menu
Select MORE 1/4 page menu
Select preference time (5 min/10 min/ 30
min/ 1 hr/ 2 hrs/ 4 hrs) or turn off the auto
power off function

7
To Select Language for Quick Help
Open User menu
Open Utility menu
Select MORE 1/4 page menu
Select language (English/French/Italian/
Portuguese/German/Spanish/Korean/
Japanese/Traditional Chinese/Simplified
Chinese)
To Adjust Contrast of Display
Open User menu
Open Display menu
Select MORE 1/2 page menu
Enter once to release the fixed contrast value
Turn rotary switch clockwise to reduce
brightness (contrast value shows increment
from 20 to 79) and vice versa
Enter once to fix the contrast value
To Compensate Scope Probe
To compensate the probe characteristic to
the scope’s channel, perform probe
adjustment. This step must be performed
whenever a passive probe is first attached to
the input channel. Connect the passive probe
to channel 2 and probe contact to channel 1
to obtain input signal 3 Vp- p with 1 kHz.
Open User menu
Open Utility menu
Select MORE 3/4 page menu
Enter probe calibration
Select probe attenuation
Enter to start probe adjustment
Trimmer capacitor
Ensure the shape of the displayed pulse is
properly compensated. If not, adjust the
trimmer capacitor to obtain the flattest
square wave possible.
Proper compensated
Under compensated
Over compensated

8
Scope Screen Display
Agilent U1600B Series offers a 320×240 color LCD display.
No. Description / Function
1To display the status of channel 1 and channel 2 in volt/div and time/div
2To display input waveform from channel 1 and channel 2
3To display trigger position in window
4To show the battery level and to indicate battery charging when connected to AC line power
5To display signal acquisition status
6To display signal triggering mode and the status of the triggering
7To display resulting auto measurement values
8To d i s p l ay t i m e
9To display menu of the functions by pressing the respective buttons and softkeys
10 To display numeric measurement value in meter mode
11 To indicate the meter is in auto ranging mode
12 To display analogue bar graph for measurement value
Table 1 Descriptions of the handheld digital oscilloscope main display
Figure 2 Multimeter display
Figure 1 Oscilloscope display

9
Scope Connection Configuration
Connect the scope in either single or dual channels with scope probes as
shown in figure 3.
Figure 3 Connection for scope measurement
Scope Menu Sub Menu Description
CH1 / CH2
MORE 1/2 page
On/Off To turn on or off waveform display for channel 1 and channel 2
Coupling To select channel coupling:
DC: To display both AC and DC component of the input waveform
AC: DC offset voltage will be removed from the input waveform, only AC com-
ponent will be shown
GND: Input signal is grounded
Position To adjust the reference ground position, turn rotary switch clockwise to raise to
positive position and vice versa
To set the position, press rotary switch
CH1 / CH2
MORE 2/2 page
Probe Select the probe attenuation 1X, 10X or 100X
Invert To turn on or off waveform invert function
Position to 0 Reset the reference ground position to zero volt
Table 2 Function descriptions of scope menu