Agora Models FERRARI 312 T4 User manual

STAGES 43-52
PACK
0606
THE LEGENDARY 1970sF1 FERRARI
SCALE
1:8
FERRARI

SCALE
1:8
Contents
STAGE 43
BRAKE AIR INTAKE................................................. 1
STAGE 44
WISHBONE ARMS ................................................. 5
STAGE 45
PARTS TO SECURE SUSPENSION TO
CHASSIS..................................................................... 9
STAGE 46
LEFT SUSPENSION JOINTS AND
WISHBONE ARMS ................................................13
STAGE 47
BRAKE LINE FITTINGS AND FIRST
STEERING PARTS ................................................. 17
STAGE 48
LEFT AND RIGHT SIDES OF BODYWORK....21
STAGE 49
CROSS WRENCH AND DRAG LINK
PLATES.....................................................................25
STAGE 50
LEFT HAND RADIATOR PARTS ...................... 29
STAGE 51
RIGHT HAND RADIATOR PARTS ....................33
STAGE 52
COOLANT FLUID TANK......................................37
FERRARI
Produced under license of Ferrari S.p.A.
The name FERRARI, the PRANCING HORSE
device, all associated logos and distinctive
designs are property of FERRARI S.p.A.
The body designs of the Ferrari cars are
protected as Ferrari S.p.A. property under
design, trademark and trade dress regulations.
© Agora Models
WARNING: NOT SUITABLE
FOR CHILDREN UNDER THE
AGE OF 14. THIS PRODUCT IS
NOT A TOY AND IS NOT
DESIGNED OR INTENDED
FOR USE IN PLAY.
ITEMS MAY VARY FROM
THOSE SHOWN.

1
FERRARI 312 t4
312 T4
Pack 06 . STAGe 43
Stage
PACK 06
LIST OF PARTSLIST OF PARTS
1Air intake (outer)
2Hubcap
3Air duct (inner)
4Brake disc support
BRAKE AIR
INTAKE
WITH THE PARTS INCLUDED IN THIS STAGE, YOU CAN CONTINUE
BUILDING THE SECOND FRONT WHEEL BRAKE.
43
13
4
2

2
FERRARI 312 t4 Pack 06 . STAGe 43
43-01 Place the two parts of
the brake air intake together
on your work surface, so they
are facing the direction shown
in the image. You can see the
interlocking structures that
allow you to press the two
parts together.
43-02
Join the two parts by pressing
them together so that the
interlocking structures can
bond perfectly together.
01
02

3
FERRARI 312 t4 Pack 06 . STAGe 43
43-03 Take the brake assembly
that you built in the previous
stage and place it alongside
the air intake, as shown in the
photo. The brake assembly has
two pins (yellow circles) and a
reference mark (yellow arrow);
the air intake has two holes and
a small recess.
43-04 Using the parts
highlighted in the previous
step, join the air intake to the
front brake assembly.
03
04

4
FERRARI 312 t4 Pack 06 . STAGe 43
In the next stageIn the next stage
Parts for the front right
suspension and the
necessary screws
for their assembly.
Final result
You have just completed
another important step in
building the brake assembly
on the second front wheel.
05
43-05 Now take the brake disc
support. Join it to the brake
disc. The pins and fixing holes
mean they can simply snap
together.

5
FERRARI 312 t4 Pack 06 . STAGE 44
312 T4
Stage
PACK 06
LIST OF PARTSLIST OF PARTS
1Lower arm
2Steering slider
3Shock absorber
4Upper arm
Screws
Four type C screws
Two type D screws
WISHBONE
ARMS
STAGE 44 INCLUDES THE PARTS THAT SERVE TO BUILD THE
RIGHT FRONT SUSPENSION OF YOUR 1:8 SCALE FERRARI 312 T4.
USING THESE INSTRUCTIONS, YOU CAN START TO BUILD
THIS MECHANICAL ASSEMBLY.
44
1
23
4
4type C screws 2type D screws

6
FERRARI 312 t4 Pack 06 . STAGe 44
44-01 Place the upper wishbone and the shock absorber
on your work surface. Rest the shock absorber plate in the
seat highlighted by a circle in the image (pay attention
to the reference notch – highlighted by the arrow in the
photo –, which needs to match with the recess in the shock
absorber plate). Secure the assembly with a type D screw.
44-02 Press the slot at the free end of the upper wishbone arm
onto the relevant column of the brake assembly. In this case
fasten with a type C screw. After tightening all the way, loosen
the screw by a quarter turn so as that the brake can move.
01
02

7
FERRARI 312 t4 Pack 06 . STAGe 44
44-03 Take the lower
wishbone arm and the
steering slider. There are two
columns to secure the brake
assembly, shown by the circle
in the image.
44-04 Now it is the turn of
the lower wishbone arm. In
this case too, you should look
at the images to ensure
the parts are facing
the right way. Use
a type C screw for
the lower arm.
03
04

8
FERRARI 312 t4 Pack 06 . STAGe 44
In the next stageIn the next stage
New parts for the right front suspension and
the screws needed to assemble the parts.
44-05 Lastly, place the
steering slider and secure it
with another type C screw.
05
Final result
Now you have started to build
the right front suspension of
your 1:8 scale Ferrari 312 T4.

9
FERRARI 312 t4 Pack 06 . STAGE 45
312 T4
STAG e
PACK 06
LIST OF PARTSLIST OF PARTS
1Front link
2Rear link
3Shock absorber
4Hex-head screw
5Rear suspension joint
Screws
Four type D screws
Two type E screws
Six type G screws
Two type L screws
PARTS TO SECURE
SUSPENSION
TO CHASSIS
NOW YOU HAVE THE PARTS YOU
NEED TO COMPLETE THE RIGHT
FRONT SUSPENSION AND
SECURE IT TO THE CHASSIS
OF YOUR FERRARI 312 T4.
45
5
1
2
3
4
6type G screws4type D screws 2type L screws2type E screws

10
FERRARI 312 t4 Pack 06 . STAGe 45
45-01
Take the
cockpit cradle
and the
sheath
provided
with stage
30. Insert
the three
tubes from
the console
on the left of
the steering
wheel into
the sheath.
45-02 Now place the cockpit cradle on the
underbody, starting from the front. Press the
rear section until the two pins (shown inside
the inset photo) have slotted perfectly into the
relevant columns.
45-03 Place the front and back
joints of the suspension in their
correct position and fix them
to the underbody using two
type D screws. Important: the
wider slots need to be facing
the front of the car.
03
01
02

11
FERRARI 312 t4 Pack 06 . STAGe 45
45-04 Use the hex-head screw to join the
upper wishbone arm to the front and rear links.
Make sure the parts are facing the right way, as
shown in the image.
45-05 Join the ends of the lower wishbone
arm to the rear joint of the suspension and the
master cylinder support. The bottom slot of
the shock absorber must be inserted into the
shock absorber joint.
45-07 Using three type G screws, fasten the
rear track rod of the suspension under the
underbody.
45-06 Secure the
lower wishbone
arm in the rear
joint using a type
E screw. Use
another type E
screw to secure the
shock absorber.
04 05
07
06

12
FERRARI 312 t4 Pack 06 . STAGe 45
In the next stageIn the next stage
The suspension mounting brackets and
joints, together with the screws needed for
assembly.
45-08
Now it is time
for the front
track rod.
Bring the two
assembly
holes
into line with
those of the
bottom plate,
then secure
with two type
G screws.
08
Final result
Now you have fastened the front right suspension
to your 1:8 scale Ferrari 312 T4.
Place the model in a safe place.

13
FERRARI 312 t4 Pack 06 . STAGe 46
312 T4
PACK 06
STAG e
LIST OF PARTSLIST OF PARTS
1Left wishbone arm
2Right wishbone arm
3Rear suspension joint
4Shock absorber
Screws
Four type D screws
Three type E screws
Three type F screws
Six type G screws
Five type N screws
LEFT
SUSPENSION
JOINTS AND
WISHBONE ARMS
WITH THE CONTENTS OF THIS STAGE YOU CAN
SECURE THE FRONT LEFT SUSPENSION TO
THE CHASSIS, COMPLETING THE FRONT OF
YOUR 1:8 SCALE FERRARI 312 T4.
46
1
2
3
4
6type G screws
3type F screws
4type D screws
5type N screws
3type E screws

14
FERRARI 312 t4 Pack 06 . STAGe 46
46-01
Place the two
joints on the
left side of the
chassis and
secure them
with two
type D
screws.
46-02 Join the ends of the
lower left suspension arm
(which you built in the
assembly stage for
stage 6) to the rear
suspension joint and
the master cylinders
support. The bottom
slot of the shock
absorber must be
inserted into the
shock absorber joint.
Insert two type E screws
into the brackets in
question.
46-03 With three type G screws,
fasten the rear track rod
of the left wishbone to
the chassis. Then pass
on to the front track
rod. Bring the two
assembly holes
into line with those
of the chassis then
secure with two
type G screws.
You may find this
easier if you remove
the wheel first.
01
02
03

15
FERRARI 312 t4 Pack 06 . STAGe 46
46-04 Take
the front wheel,
a type L screw
and the hubcap,
included in previous
stages. Fix the wheel to
the left front suspension
assembly using the type L
screw.
46-05 All that is left
is to position the
hubcap, using the
two assembly pins.
Now the two front
wheels are joined
to the model being
constructed.
46-06 Take a close
look at the image
of the wishbone
arms. Their almost
triangular end has
a reproduction of a
flanged hex-head screw
on one side, and on the
other, the copy of a nut
and the end of a screw.
The first, which is the face with
the bolt head (on the right in the photo) is
the side that needs to be facing upwards.
05
04
06

16
FERRARI 312 t4 Pack 06 . STAGe 46
In the next stageIn the next stage
Brake line connections,
the first parts for the steering
system, and the assembly
screws.
46-08
Take two more type N screws
and insert them in the
positions circled in the image.
46-07
Fit the wishbones in question.
For each arm, couple the
fork-shaped end into the
suspension support, and
the triangular shape in the
relevant peg in the chassis.
Then drive two type N screws
into the positions indicated in
the image.
08
Final result
You have completed the assembly of the mechanical
parts in the front section of your 1:8 scale Ferrari 312 T4.
Place the model in a safe place.
07

17
FERRARI 312 t4 Pack 06 . STAGe 47
312 T4
Stage
PACK 06
LIST OF PARTSLIST OF PARTS
1Reinforcement plate for steering
wheel support frame
2Steering joint plate
3Steering rack
4Front brake line fittings
Screws
Five type E screws
Four type J screws
BRAKE LINE
FITTINGS
AND FIRST
STEERING PARTS
NEXT YOU'LL BE
ASSEMBLING THE BRAKE
LINES. THESE CAN BE
BUILT WITHOUT ADDING
THE METAL LINER, BUT
INCLUDING IT GIVES A
MORE REALISTIC RESULT.
47
1
2
34
5type E screws 4type J screws

18
FERRARI 312 t4 Pack 06 . STAGe 47
47-01 Take a length of the
same metal wire used to
tie the spark plug cables
(stage 18). Take the brake
lines, installed on the master
cylinders in the assembly
steps in stage 39 and then
removed in stage 41. Insert a
piece of metal wire into one
of the brake lines. The line is
130 mm long; the metal lining
must be about 124 mm.
47-02 Apply a small
amount of two-
component adhesive to
the longer end of a brake
line fitting. Then push a brake
line (with metal wire lining)
onto this end.
47-03 Follow the same steps
to complete the second brake
line, adding the metal lining
and fitting.
01
02
03