Agora Models CORVETTE STING RAY 1963-Z06/N03 Manual

General Motors Trademarks used under license by Premium & Collectibles Trading Co. Ltd on behalf of Agora Models.
STAGE 25: ASSEMBLING THE REAR
LEFT WHEEL
STAGE 26: BUILDING THE REAR
CONTROL ARMS
STAGE 27: ASSEMBLING THE REAR
RIGHT WHEEL
STAGE 28: FITTING THE GEAR BOX
STAGE 29: ATTACHING THE REAR CHASSIS
STAGE 30: BUILDING THE REAR
DIFFERENTIAL CASE
STAGE 31: ATTACHING THE REAR LEAF SPRING
STAGE 32: FITTING THE REAR SUSPENSION
AND WHEELS
Pack 04
BUILD INSTRUCTIONS

AGORAMODELS CORVETTE STING RAY
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Corvette, the left- or right-hand side refers to that side as if
you are sitting in the car.
Advice from the experts
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
!

AGORAMODELS CORVETTE STING RAY
3
XXX
Name
Tyre
Outer wheel rim
Inner wheel rim
Six-spoke wheel cover
Three-bar spinner
CM screws x3
DP screws x3
STAGE 25 PARTS LIST
In this stage you’ll build the rear left
wheel. The rear wheels will be fitted
at the end of this pack.
Tyre
Three-bar spinner
Six-spoke wheel cover
CM x3
Outer wheel rim Inner wheel rim
DP x3
Stage 25: Assembling the Rear Left Wheel

AGORAMODELS CORVETTE STING RAY
4
1a 2b
Fit the outer wheel rim into the tyre (1a, arrow) until it fits flush (1b). Turn over and fit the inner wheel rim onto the outer rim, aligning the
holes (2a, circled). Secure using 2x CM screws (2b).
3b 4
Turn the assembly back over and fit the six-spoke wheel cover in
position, aligning the indent of the cover with the air valve (3a, circled).
Secure the wheel cover with 2x DP screws.
1b
2a
CM
3a
DP
Stage 25: Assembling the Rear Left Wheel

AGORAMODELS CORVETTE STING RAY
5
5 6
Push the three-bar spinner into the wheel cover (arrow). Alternatively,
you may wish to wait until the wheel has been mounted in stage 32.
STAGE COMPLETE
Stage 25: Assembling the Rear Left Wheel

AGORAMODELS CORVETTE STING RAY
6
XXX
Name
Rear left brake drum
Brake drum cover (L)
Rear left knuckle
Brake drum cover (R)
Rear right knuckle
Upper control arm (L)
Lower control arm (L)
Upper control arm (R)
Lower control arm (R)
Transmission shaft connector (x2)
AM screws (x5)
RM screws (x5)
TM screws (x3)
STAGE 26 PARTS LIST
In this stage you’ll begin making
the mounts for the rear wheels
by building the control arms and
fitting the brake drum covers.
Rear left
brake drum
Upper control arm (L)
AM x5
Stage 26: Building the Rear Control Arms
Brake drum
cover (L)
Rear left
knuckle
Brake drum
cover (R)
Rear right
knuckle
Upper control arm (R)Lower control arm (L) Lower control arm (R)
Transmission shaft
connector (x2)
RM x5 TM x3

AGORAMODELS CORVETTE STING RAY
7
1a
3b
2b
4b
Fit the left lower control arm into the rear left knuckle, marked with an
‘L’ (1a, circled). Secure using a TM screw (1b).
While holding the connector in place (3a), turn the assembly over and
secure using an RM screw (3b).
Take the left upper control arm (2a, marked with an ‘L’, circled) and a
transmission shaft connector. Note it has a D-shaped post (2a, arrow).
Fit the connector into the control arm (2b).
Align the left knuckle and upper control arm as shown (4a) then push
screw posts of the knuckle into the holes of the arm (4b).
1b
TM
RM
3a 4a
Stage 26: Building the Rear Control Arms
2a

AGORAMODELS CORVETTE STING RAY
8
5
7
6
8a
Fix the parts together using 2x AM screws.
The brake drum cover will be loosely fitted for now, take care not to
lose it during the assembly.
Place the left brake drum cover, marked with an ‘L’ (circled, inset), over
the knuckle as shown.
Fit the right lower control arm into the rear right knuckle, marked with
an ‘R’ (8a, circled). Secure using a TM screw (8b).
AM
TM
8b
Stage 26: Building the Rear Control Arms

AGORAMODELS CORVETTE STING RAY
9
9b 10b
Fit the other transmission shaft connector into the right upper control
arm, marked with an ‘R’ (9a). Secure using an RM screw (9b).
Fit the right knuckle into the upper control arm (10a) then secure
using 2x AM screws (10b).
11b 12b
Place the right brake drum cover, marked with an ‘R’, over the knuckle. Retrieve the wheel assembled in stage 25. Fit the rear left brake drum
onto the outer wheel rim (12a, arrow), using the locking pin and hole to
align the parts correctly (12a, circled). Secure using 2x RM screws (12b).
RM
9a
AM
11a
10a
12a
RM
Stage 26: Building the Rear Control Arms

AGORAMODELS CORVETTE STING RAY
10
STAGE COMPLETE
Stage 26: Building the Rear Control Arms