Agora Models Hachette Mitsubishi A6MZERO FIGHTER Manual

STAGE 01: THE PROPELLER
STAGE 02: ENGINE, LOWER ENGINE COWLING & CYLINDERS
STAGE 03: ENGINE, UPPER ENGINE COWLING & CYLINDERS
STAGE 04: ENGINE CYLINDERS
STAGE 05: ENGINE CYLINDERS & OIL PIPES
Pack 01 |Build Instructions
Your 1:18 model of the Japanese Zero is reproduced in the most exquisite
detail, with electronics allowing you to recreate aeronautical operations such
as take-off and landing, turning, firing and night combat. Lights, machine-gun
and propeller sounds bring your legendary fighter plane to life.
In your first model pack, you will assemble:
© 2020 Hachette Partworks Ltd.
North America Edition by Agora Models

2
AGORAMODELS A6M ZERO
Not suitable for children under the age of 14. This product is not a toy and is not designed for use in play. Keep
the parts out of the reach of small children. Some parts may have sharp edges. Please handle them with care.
Advice from the experts
Spare screws are included with each part. Occasionally, you may
be instructed to keep spare or unused screws for a later stage.
Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite
similar, but the threads do vary slightly. Using the wrong screws
may damage the parts.
When securing parts together using multiple screws, fit each
screw loosely to ensure all the parts are correctly aligned before
gently tightening them firmly, but not overtight, in the order in
which you placed them.
The screwdriver can be magnetised by stroking it with a magnet
(fridge magnet, etc.) enabling it to hold the screws and make
assembly easier.
If a screw is tight going into a metal part, do not force it as you
may shear the head off. Remove it and put a tiny smear of Vaseline,
soap or light oil on the thread. That will lubricate it and make it
easier to drive home.
During the course of this build, you will receive many pieces that
you will assemble immediately – following the instructions in the
corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.

STAGE 01 PARTS PARTS LIST
You will also need: superglue, tweezers.
No.PART
001-01
001-02
001-03
001-04
001-05
001-06
001-07
001-08
001-09
001-10
001-11
001-12
3
3
1
1
1
1
1
1
1
1
1
3
MATERIAL
ABS resin
Die-cast
Die-cast
Die-cast
ABS resin
ABS resin
ABS resin
ABS resin
POM
Steel / ABS resin
Steel
Steel
001-01
001-02
001-04 001-10
001-05
001-03
001-07
001-08
001-09
001-11
001-06
001-12
Stage 01 Assembly
The Propeller
Stage 01: Assembling
the Propeller
In the first stage of building your Zero fighter plane,
you will assemble the propeller.
3
AGORAMODELS A6M ZERO

STEP 1
Apply a small drop of superglue to the
three pins on 001-08 and insert them into
the small holes in 001-04.
Fit 001-09 into the parts already assembled
in picture1. Insert 001-09 ensuring that the
teeth facing up. Do not glue.
TIP
Insert the convex part in the centre of
001-08 firmly into the hole in the centre of
001-04. Study the picture below carefully.
STEP 2
Insert 001-02 into 001-0. 001-01 is a jig to prevent the angles of the
three blades from shifting. Do not glue it as it will no longer be
needed after assembly.
Fit 001-02 into the parts assembled in picture1. Do not glue.
STEP 3
Place 001-07 on the parts assembled in STEP 2 and fix it with a
001-11 screw.
STEP 4
Apply a small amount of superglue to the three pins of 001-05
and insert them into the holes of 001-07.
Apply a small amount of superglue to the center pin of 001-05
before pushing 001-06 in place on top.
STEP 5
Cover the parts assembled in STEP 4 with 001-03, carefully turn it over and fix it with 001-12 screws. Do not glue.
TIP
The angle of the blades can be operated by hand. Check that
the three blades are moving together.
001-08
001-01
001-02
001-07
001-11
001-04
001-09
001-05
001-03
001-12
001-06
001-04
001-02
12
12
12
STAGE COMPLETE
: Glue
: Don’t glue
4
AGORAMODELS A6M ZERO

STEP 1
Apply a small drop of superglue to the
three pins on 001-08 and insert them into
the small holes in 001-04.
Fit 001-09 into the parts already assembled
in picture1. Insert 001-09 ensuring that the
teeth facing up. Do not glue.
TIP
Insert the convex part in the centre of
001-08 firmly into the hole in the centre of
001-04. Study the picture below carefully.
STEP 2
Insert 001-02 into 001-0. 001-01 is a jig to prevent the angles of the
three blades from shifting. Do not glue it as it will no longer be
needed after assembly.
Fit 001-02 into the parts assembled in picture1. Do not glue.
STEP 3
Place 001-07 on the parts assembled in STEP 2 and fix it with a
001-11 screw.
STEP 4
Apply a small amount of superglue to the three pins of 001-05
and insert them into the holes of 001-07.
Apply a small amount of superglue to the center pin of 001-05
before pushing 001-06 in place on top.
STEP 5
Cover the parts assembled in STEP 4 with 001-03, carefully turn it over and fix it with 001-12 screws. Do not glue.
TIP
The angle of the blades can be operated by hand. Check that
the three blades are moving together.
001-08
001-01
001-02
001-07
001-11
001-04
001-09
001-05
001-03
001-12
001-06
001-04
001-02
12
12
12
STAGE COMPLETE
: Glue
: Don’t glue
5
AGORAMODELS A6M ZERO

You will also need: superglue, tweezers.
* 0002-04 and 002-07 will not be used in this stage. Keep them in a safe place
Stage 02 Assembly
The Engine
002-01
002-02
002-03
002-04
002-05
002-06
002-07
3
3
1
1
3
3
1
Die-cast
Die-cast
Die-cast
Die-cast
ABS resin
ABS resin
ABS resin
002-04
002-03
002-01
002-06
002-05
002-07
002-02
STAGE 02 PARTS PARTS LIST
No.PART MATERIAL
Stage 02: Building the
Engine (Part 1)
In this stage you will start building the Sakae 21
14-cylinder radial engine of your Zero Fighter Type 52.
6
AGORAMODELS A6M ZERO

STEP 1
Glue 002-05 & 002-06 to the cylinder
assembly in 1. Make three of these.
Apply a small amount of superglue to the
two pins on part 002-01 and insert them
into the holes on part 002-02 to join them.
Make 3 of these.
NOTE
Parts 002-05 & 002-06 are similar, so be
careful not to make a mistake. Make sure
that the holes on the sides face outward.
NOTE
Study part 002-03 carefully. The holes
are marked C and D. Ensure the
assemblies are located in the correct
holes - position D.
NOTE
This shows how your assembly should look.
STEP 2
002-01
002-02
1
Fit the three assemblies made in STEP 1 to the crank-
case – part 002-03 – by aligning the projections with the
holes marked D and pushing the pieces together. Do
not glue.
2
002-06
002-05
002-03
002-05 002-06
Protrusions face outward.
NOTE
Parts 002-01 & 002-02 are marked with
the letter D.
002-02 002-01
STAGE COMPLETE
7
AGORAMODELS A6M ZERO

STEP 1
Glue 002-05 & 002-06 to the cylinder
assembly in 1. Make three of these.
Apply a small amount of superglue to the
two pins on part 002-01 and insert them
into the holes on part 002-02 to join them.
Make 3 of these.
NOTE
Parts 002-05 & 002-06 are similar, so be
careful not to make a mistake. Make sure
that the holes on the sides face outward.
NOTE
Study part 002-03 carefully. The holes
are marked C and D. Ensure the
assemblies are located in the correct
holes - position D.
NOTE
This shows how your assembly should look.
STEP 2
002-01
002-02
1
Fit the three assemblies made in STEP 1 to the crank-
case – part 002-03 – by aligning the projections with the
holes marked D and pushing the pieces together. Do
not glue.
2
002-06
002-05
002-03
002-05 002-06
Protrusions face outward.
NOTE
Parts 002-01 & 002-02 are marked with
the letter D.
002-02 002-01
STAGE COMPLETE
8
AGORAMODELS A6M ZERO

You will also need: superglue, twezers, screwdriver.
* Part 0003-02 will not be used in this stage. Keep it in a safe place..
Stage 03 Assembly
The Engine / Engine Cowling
003-01
003-02
003-03
003-04
003-05
003-06
003-07
2
2
1
1
2
2
1
003-04
003-07 003-01 003-05
003-06
003-03
003-02
STAGE 03 PARTS PARTS LIST
No.
Die-cast
Die-cast
Die-cast
ABS resin
ABS resin
ABS resin
ABS resin
MATERIALPART
Stage 03: Building
the Engine
(Part 2)
You will continue to build the engine
cylinders and add the upper cowling.
9
AGORAMODELS A6M ZERO

STEP 1
STEP 3
1 2
Apply a small amount of superglue to the two pins on 003-03 and
attach to 003-04.
Fit the upper part of the engine cowling assembled in 1 to part
002-04 . Do not glue as this is secured with a magnet.
STEP 2
Insert the protrusions on the cylinder
assemblies from Step 1 into the holes
marked C on the crankcase assembled
from Stage 02. Do not glue.
003-02
003-01
003-03
003-04
002-04
Apply a small amount of superglue to the two pins on 003-01 and insert
them into the holes of 003-02 to join them. Make two of these.
1NOTE
Parts 003-01 and
003-02 are
marked with a C.
Glue 003-05 & 003-06 to the cylinder assembled in 1. Make two of
these. Please note that 003-05 & 003-06 are different shapes.
003-05
003-06
2
003-02 003-01
STAGE COMPLETE
10
AGORAMODELS A6M ZERO