Agora Models OPTIMUS PRIME Pack 02 Manual

Pack 02
BUILD INSTRUCTIONS
ASSEMBLING THE LEFT SHOULDER & ARM
TRANSFORMERS and HASBRO and all related trademarks and logos are trademarks of Hasbro, Inc. ©2022 Hasbro.

AGORAMODELS 2OPTIMUS PRIME
Please keep ALL unused screws as they may be required in a later stage.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
Some parts will require a little glue for assembly. Please apply glue sparingly and use a cocktail
stick so that you don’t use too much nor apply the glue too heavily. We recommend superglue
gel or Extra Thin Liquid modeling glue. Where possible, parts should be test-fitted in place
before gluing.
Look out for the glue symbol and apply glue to the red area indicated in the picture.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
in the tray supplied, for use in future assembly stages.
Always protect the paint finish on components by placing a cutting mat, sheet of white paper
or soft cloth on your work surface.
Left and Right! When building your Optimus Prime, the left or right hand side refers to each
side as viewed by Optimus Prime. Optimus Prime’s left arm is on the viewer’s right.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!
!

AGORAMODELS 3OPTIMUS PRIME
Pack 2: Assembling the Left Shoulder & Arm

AGORAMODELS 4OPTIMUS PRIME
Pack 2 Parts
TRAY 1:
TR-2-48 x4
TR-2-59
TR-2-07
TR-2-06
TR-2-46 x2
PB2.3x6 mm
x31
M3x8 mm
x20
TR-2-30
TR-2-28
TR-2-49 x36
TR-2-50 x8
TR-2-58
(nut 3) x11
M3x6 mm
x8
M3x14 mm
x4
M3x10 mm
x4
TR-2-14 TR-2-15
TR-2-42
TR-2-19 TR-2-18
TR-2-02
TR-2-43
TR-2-33
TR-2-17
TR-2-25

AGORAMODELS 5OPTIMUS PRIME
Pack 2 Parts
TRAY 2:
TR-2-03
TR-2-34
TR-2-32 TR-2-21
TR-2-20
TR-2-22
TR-2-23
TR-2-44
TR-2-47 x2
TR-2-41
TR-2-29
TR-2-16
TR-2-45 x3
TR-2-26/27 TR-2-10 TR-2-11

AGORAMODELS 6OPTIMUS PRIME
Pack 2 Parts
TRAY 3
TR-2-01 TR-2-05
TR-2-12 ‘1’
TR-2-13 ‘2’
TR-2-04 TR-2-35
PB2x4 mm
x5
PWM2x4 mm
x9
PWM2x6 mm
x5
TR-2-37
TR-2-31
TR-2-36
TR-2-39
TR-2-38
TR-2-40 TR-2-08 TR-2-09
TR-2-24

AGORAMODELS 7OPTIMUS PRIME
Assembling the Left Shoulder & Arm
Glue the assembly from
step 1 as shown in 2a, then
fix TR-2-43 over the glued
end as shown.
Glue TR-2-17 as shown
in 2b, then fix it to the
opposite end of the
assembly, taking care
to align the glued fixing
points.
1
2
STEP 1
STEP 3
Align TR-2-14 and TR-2-15 as shown and secure them
together using 2x PB2x4 mm screws.
STEP 2
2a 2b
TR-2-43
TR-2-17
Apply a little glue to TR-2-33 as shown in 4a and fix
to the assembly from step 3. Study the inset image
(bottom, right) to check that part TR-2-33 is in the
correct orientation. There is a step at one end.
3
TR-2-42
Push TR-2-42 onto the assembly from step 2, paying
attention to the detail highlighted in the inset
image. Check that the slot in TR-2-42 is oriented
over the corresponding slot in the assembly.
STEP 4
TR-2-33
4
4a
PB2x4
TR-2-15
TR-2-14

AGORAMODELS 8OPTIMUS PRIME
Assembling the Left Shoulder & Arm
First attach TR-2-40 to TR-2-02,
Fix TR-2-02 to the assembly from step 4 using
1x PB2.3x6 mm screw.
STEP 5
TR-2-40
TR-2-02
PB2.3x6
5
5b
Thread TR-2-49 and TR-2-50 onto a M3x8 mm
screw before inserting the assembled screw
through a corner screw hole hole in TR-2-18. Then
attach TR-2-48. Repeat with the other 3 sets,
driving them through the remaining 3 screw holes.
Fasten each screw quite tight.
STEP 6
6a
6b
TR-2-48
TR-2-18
M3x8
TR-2-49
TR-2-50

AGORAMODELS 9OPTIMUS PRIME
Assembling the Left Shoulder & Arm
Push TR-2-46 through the hole in TR-2-18, paying close attention to the
orientation. The top and bottom edges are rounded, the left and right edges are flat
(see 8a–d on the next page). Thread TR-2-49 onto a M3x6 mm screw and make 4
sets, using them to secure TR-2-46 in place as shown.
STEP 8
TR-2-46
TR-2-49
M3x6
Push assembly A into TR-2-25 as shown.
Thread washers TR-2-49 and then TR-2-50 onto a
M3x8 mm screw. Make 4 sets and then screw them
into TR-2-48 as shown.
STEP 7
7a 7b
7c
8
TR-2-25
M3x8
TR-2-49
TR-2-50
TR-2-48
A

AGORAMODELS 10 OPTIMUS PRIME
Assembling the Left Shoulder & Arm
IMPORTANT! Check that the red sides are flat.
Align assembly A, TR-2-28
and assembly B as shown.
Push the parts together.
Thread washers
TR-2-49 onto screws
M3x14 mm and make 4
sets. Fix the parts together
as shown, pushing each
screw assembly through
the four screw holes on
each part.
Place a washer
TR-2-49 onto a M3x6 mm
screw before pushing it
through TR-2-19 to attach
it to TR-2-46. Repeat three
more times, pushing the
screw assemblies through
the remaining three
screw holes. There is no
particular direction for
parts at this stage.
M3x6
TR-2-49
TR-2-19
TR-2-46
TR-2-28
A
B
STEP 8 CONT...
STEP 10
STEP 9
9
10
8a 8b
8c 8d
Correct Incorrect
TR-2-49 M3x14