Agri-Fab 45-0390 User manual

ASSEMBLY INSTRUCTIONS
The Tine Harrow consists of two sections of 4 rows
of tines (2-1/2' length) with welded hooks on the front
section, open hooks and "S" hooks on the rear section.
Total length is 8 rows of tines (5' length.)
FIGURE 1
FIGURE 4
1.
The harrow sections are in two labelled bundles. The
sections with welded front hooks will be located at
the front and the sections with the open hooks and
s-hooks will be located at the rear. Unroll the front and
rear sections and line them up. Note how the front and
rear sections are joined. See fi gures 1 and 2.
FIGURE 2
2.
Slide the drawbar through the welded hooks on the
front of the harrow section. See fi gure 3.
FIGURE 3
3.
Make sure the top angle of the drawbar which
contains the holes is facing forward, away from the
section. Use a fl anged nut to attach a J-bolt with nut
to the top of the drawbar at each end to secure the
drawbar to the section. See fi gure 4.
MODEL NO.
45-0390 TINE HARROW
™
FIGURE 5
4.
Attach the clevis to the middle link in the chain using a
5/16" x 2-1/4" hex bolt and 5/16" nylock nut.
5.
Attach the chain to the drawbar with two 7/16" x 1-1/2"
carriage bolts, lock washers and nuts. The chain can
be attached in two positions on the drawbar depending
on the size of the harrow and turning radius desired.
See fi gure 6.
FIGURE 6
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com

OPERATION
The Tine Harrow can be pulled in many different
confi gurations.
Aggressive:
Aggressive:
For maximum pe
For maximum pe
netration.
For this setup, slide the drawbar through the welded rings
and use the open hooks to connect the back to the front
section. This is the most common harrow confi guration.
This setting allows for the most work per pass.
Backward: For light penetration.
Backward: For light penetration.
This setup uses the same confi guration as the aggressive
except you slide the drawbar through the S-hooks instead
of the welded hooks. The tines laying fl at will knock down
material without penetrating very deep.
Upside Down: For smoothing.
Upside Down: For smoothing.
Simply fl ip both the front and rear sections on their back
and pull from either direction. This does a nice job of
scattering material, smoothing and as a fi nishing pass.
Combination
: For working u
: For working u
p and smoothing in one pass.
p and smoothing in one pass.
Front section
- Aggressive with maximum penetration.
Rear section
- Backward (for light penetration) or Upside
Down (for smoothing.)
This is a popular setup for horse arenas and driveways.
By having the front section digging in and the rear section
smoothing out, you can work up and dress up in one
pass.
REPAIR PARTS FOR TINE HARROW MODEL 45-0390
11
2
4
6
5
3
7
8
10
9
10
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
No. No.
No. No.
No. No.
1 40077 2 Drag Array
1 40077 2 Drag Array
1 40077 2 Drag Array
1 40077 2 Drag Array
1 40077 2 Drag Array
2 40078 1 Tow Bar
2 40078 1 Tow Bar
2 40078 1 Tow Bar
2 40078 1 Tow Bar
2 40078 1 Tow Bar
3 40076 1 Tow Linkage Chain
3 40076 1 Tow Linkage Chain
3 40076 1 Tow Linkage Chain
3 40076 1 Tow Linkage Chain
3 40076 1 Tow Linkage Chain
4 24221 1 Clevis
4 24221 1 Clevis
4 24221 1 Clevis
4 24221 1 Clevis
4 24221 1 Clevis
5 43224 1 5/16" x 2-1/4" Hex Bolt
5 43224 1 5/16" x 2-1/4" Hex Bolt
5 43224 1 5/16" x 2-1/4" Hex Bolt
5 43224 1 5/16" x 2-1/4" Hex Bolt
5 43224 1 5/16" x 2-1/4" Hex Bolt
6 47810 1 5/16" Nylock Nut
6 47810 1 5/16" Nylock Nut
6 47810 1 5/16" Nylock Nut
6 47810 1 5/16" Nylock Nut
6 47810 1 5/16" Nylock Nut
7 40257 2 J-Bolt, 7/16-14
7 40257 2 J-Bolt, 7/16-14
7 40257 2 J-Bolt, 7/16-14
7 40257 2 J-Bolt, 7/16-14
7 40257 2 J-Bolt, 7/16-14
8 HA181668 2 Bolt, 7/16-14 x 1-1/4"
8 HA181668 2 Bolt, 7/16-14 x 1-1/4"
8 HA181668 2 Bolt, 7/16-14 x 1-1/4"
8 HA181668 2 Bolt, 7/16-14 x 1-1/4"
8 HA181668 2 Bolt, 7/16-14 x 1-1/4"
9 43554 2 Lock Nut, 7/16-14
9 43554 2 Lock Nut, 7/16-14
9 43554 2 Lock Nut, 7/16-14
9 43554 2 Lock Nut, 7/16-14
9 43554 2 Lock Nut, 7/16-14
10 R73220700 4 Nut, 7/16-14
10 R73220700 4 Nut, 7/16-14
10 R73220700 4 Nut, 7/16-14
10 R73220700 4 Nut, 7/16-14
10 R73220700 4 Nut, 7/16-14
11 43555 2 Lock Washer, 7/16"
11 43555 2 Lock Washer, 7/16"
11 43555 2 Lock Washer, 7/16"
11 43555 2 Lock Washer, 7/16"
11 43555 2 Lock Washer, 7/16"
40075 1 Owners Manual
40075 1 Owners Manual
40075 1 Owners Manual
40075 1 Owners Manual
40075 1 Owners Manual
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
FORM NO. 40075 (3/06)
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com