Airwheel H3S User manual
USER MANUAL
EN
H3S
- 01 -
Backrest
Battery
Clutch
Motor
Rear wheel
Controller
Liftable armrest
Frame
Footrest
Front
wheel
Packing list
H3S 1 unit Charger 1 piece
Instruction 1 unit
Diagram
- 02 -
Installation and usage
1.Controller installation
Insert the xing lever of the
controller into the square tube
and adjust the position of the
controller to the appropriate
position, and tighten the xing
bolt to fasten it.
2. Headlight
4. Charging port
3. Power switch
Product Introduction
This product is designed for user's simple operation.
The reducer with dual back drivers is used to ensure the stability and reliability of driving.
Advanced controller, easy operation system.
Seat design complying with Human Engineering provide user with enough coziness.
The whole H3S could be folded and the pedals could be dismantled, easy for package, delivery and
storage in household.
1.
2.
3.
4.
5.
- 03 -
Main Technical Parameters
Size 1100X620X980mm Item weight ~33kg
Folding size
890X620X400mm
（controller size not
included）
Max. load 130kg
Rotation radius 1.2m Frame Aluminum alloy
6061
Standard max. speed 6Km/h Climbing capacity about 8 °
Braking performance ≤ 1.5m Slope capacity about 8 °
Charging time about 5H Battery lithium 25.2V
524Wh
Reduction gearbox worm and gear
reduction ratio 1: 32 Applicable temperature -15℃~50℃
Over-obstacle capacity <40mm Trench crossing capacity <100mm
Front wheel 8 inch Rear wheel 12.5 inch, inflatable
tire
Motor Dual-drive brush motor with clutch pull rod. Power: 200W; voltage: 24V;
revolving speed: 3776rpm
Automatic folding
function a key to automatically contract and extend
Specications
Warning
Please do not throw away the waste battery, so as not to pollute the environment. The waste
lithium battery of the product is to be recycled by the enterprise or dealer, and the government
designated outlets.
- 04 -
Horn Button
Operational Rocker
Guidance
Press the button the buzzer will buzz; Release the
button, the buzzer stop buzzing.
Horn Button
Controller instruction
Headlight switch
Power on/off
Speed indicator
Gear+/Extend
LED Light of 5 scales for
battery indicator
Gear-(decelerate)
/Contract
Exit the extending
/contracting mode
In the power-off state, the H3S is not folded
completely, click the switch to enter the ready
mode.
In the ready mode, remote control mode, riding
mode and pushing mode, click the switch to enter
the power-off state.
In the ready mode, remote control mode, riding
mode and pushing mode, click the button to turn
on/ off the headlight.
In the sleep mode, press the button over 2 seconds,
the H3S enters the extending/contracting mode.
Release it to contract.
In the extending/contracting mode, click the
button to stop contracting if it is contracting. When
extending stops, click it to contract.
In the ready mode, remote control mode and riding
mode, click the gear button to decrease one gear.
Power on/off
Headlight switch Gear-(decelerate) /Contract
- 05 -
Speed of 5 levels is available: Press the slower speed
once, and the speed will be reduced by one level;
Press the higher speed once and the speed will be
increased by one level.
When battery is fully charged, the 5 scale light is on,
and each scale represents 20% of the charge.When
only 2-scale light is on, it is advisable to charge the
H3S, which is better for the battery duration.When only
1-scale light is on, it warns that battery is under low
charge condition. In this event, it is not allowed to use
the H3S continuously; otherwise, the battery will keep
discharging and be damaged.
Speed indicatorLED Light of 5 scales for battery indicator
In the sleep mode, press the button over 2 seconds,
the H3S enters the extending/contracting mode.
Release it to extend.
In the extending/contracting mode, click the button
to stop extending if it is extending. When contracting
stops, click it to extend.
In the ready mode, remote control mode and riding
mode, click the gear button to increase one gear.
In the extending/contracting mode, click the button to
stop extending or contracting. It enters the shutdown
state.
Gear+/Extend Exit the extending/contracting mode
- 06 -
Forward:
Push the operational rocker
forward and the H3S will move
forward.
Backward:
Pull the operational rocker
backward and the H3S will
move backward.
Leftward:
Push the operational rocker
leftward and the H3S will move
to the left.
Rightward:
Push the operational rocker
rightward and the H3S will move
to the right.
The controller controls H3S to go forward, backward, and turn left and right, and to accelerate, decelerate and brake.
After turn on the switch button, push the rod forward vertically and H3S moves forward. More forward, the faster the speed.
Release the rod to slow down and when fully released, the rod is reset and H3S stops and is in the braking state. Pull the
rod backward, H3S moves backwards, more backward, the faster the speed to backward.Release the rod to slow down
and when fully released, the rod is reset and H3S stops and is in the braking state.
Similarly, turn the rod to left or right, H3S will turn left or right. Pushing more left or right, the faster the speed towards
left or right. Release the rod to slow down and when fully released, the rod is reset and H3S stops and is in the braking
state.
How to use the controller
- 07 -
Get familiar with local trafc rules.
H3S belongs to non-motor vehicle, being designed especially for the old or disabled. No driving license
is needed in accordance with trafc law, but driver of H3S should observe the same trafc rules that are
applied to pedestrians. Please drive H3S in pedestrian lane or bike lane.
Operation Practice.
Before your rst time to operate this H3S, please get familiar with all the functions of this vehicle. Practice
the operations like moving forward, increasing speed, reducing speed, stopping, moving backward, moving
uphill, moving downhill and turning direction in a safe pace with less people and good road condition. Then
you can ofcially drive on road after getting familiar with all these operations.
If possible, please nd a person familiar with this H3S to accompany you to ensure your safety during rst
on-road operation.
Do not drive the H3S after you drink, are exhausted or are not consciously clear to guarantee your safety.
Please conrm that the operator of this H3S is not suffered from any mental disease or other diseases that
may attack during driving and result in the driver's incompetence of driving the vehicle safely.
If you are taking medicine, please conrm from your doctor that if such medicine will have adverse influence
on your ability to operate the H3S.
Check the vehicle condition to conrm if the brake and various properties are normal, if the seat is locked
and ift the charge volume is enough.
Do not ret this H3S without the authorization of our company
①Get familiar with all the trafc signals marks used for pedestrians.
②Do not turn direction or cross road suddenly when driving on road.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Never expose the electrical system of this vehicle to humid environment (such as rain, snow or
fog), do not wash this vehicle with water, which will damage the electrical system. If the H3S is
wet, it could only be used after being dried and conrmed for good condition.
Do not drive the H3S under hostile weather conditions, such as rain, snow, fog, strong wind,
temperature lower than -20℃or higher than 40℃.The electrical system may be damaged under
those conditions to cause failures in control.
Do no drive the H3S on desert, beach, muddy road, road with pooled water, iced road, too
smooth road or saline and alkaline land to prevent the driving property of this vehicle.
Safety
Please read User Manual carefully and follow riding requirements during the H3S ride. Please do
not use it until riders have read User Manual carefully and learned the performance well. Do not lend it
to those who cannot manipulate H3S.
Important Note:
Attentions before operation:
You need lots of practice to grasp the skill before you ride H3S safely. If you are not skilled, or
fail to follow the user guide of this product, it may cause rider or others injury or property loss. Our
company only takes the responsibility for product defects or damage, and we are NOT responsible for
physical injury or property loss related with using products.
- 08 -
H3S is designed with only one seat not allowing for taking passengers.
H3S is not intended to be used for moving or loading cargos.
The operator should sit on the seat and grip the handle for operation.
Do not drive in a zigzag manner, take a sudden turn at high speed or incline your body to prevent H3S inclination to
one side.
Please high concentrate and drive slowly on uneven or soft road (such as grassland), when making a turn, on streets
with a lot of trafc, in shopping centers or parks.
Do not use wireless communication devices such as mobile phone during driving. These devices could only be used
when you stop the H3S in a safe place and cut off the power supply.
When moving backward, pay attention to road conditions and pedestrians at a slow speed.
Drive at a slow speed when getting out of door or elevator. It is not permitted to sit on the H3S on escalator.
Keep highly concentrated, fasten the safety belt and drive straightly at a slow speed when driving uphill or downhill. It
is not permit to drive the H3S across slopes exceeding the limit of this vehicle.
Do not cross the slope exceeding 5°at a high speed.
Do not cross over obstacles or steps higher than 4cm, which may impede the H3S from moving forward. At this
condition, release operational handle immediately.
Do not cross any gap wider than 10cm. Drive the H3S straightly when crossing gap less than 10 cm in width.
Follow trafc rules when driving through cross street and do not run a red light. When passing railway, please stop to
observe the surrounding conditions, and then drive across the railway slowly in a direction perpendicular to tracks to
avoid dropping into the gap between different sleepers.
Do not frequently lock or unlock the electrical door. Do not frequently start or stop the H3S.
Do not lend your H3S to anyone who is not familiar with or has never used this vehicle. Do not fet children paly with
electrical door lock or operational handle.
Do not use this vehicle with too much load (higher than 100KG).
If you are not going to use the H3S for over 48 hours, Please turn off the power switch.
When bring H3S to other vehicles, make sure the battery is xed.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
1.
2.
When you release the operation handle during driving and the handle has returned to the
central position, but the H3S does not stop, please lock the electrical door as soon as possible
and contact the nearest dealer.
Attentions during Operation:
Attentions after Operation:
Battery usage:
Auxiliary charge: such as short delivery time, users can directly use the battery.If the delivery time is longer (2
months or longer), the battery will lose power during storage and transport. It is better to charge the battery
before use. To charge it requires plugging the exclusive charge to the battery charging hole and connecting
AC100-240V power source for 2~4 hours until the charger is full.
The normal charge of the battery: the operation of AIR is also the discharge process of the battery. The battery
should be charged immediately after the use of the power-assisted vehicle.
Please turn off the power if not riding.
The connectors of the battery box should be fixed tightly according to the requirements (the battery box
connecting line has been reliably connected before ex-factory). Loosened or wrong connection will cause the
related parts abnormal and lead to serious damage.
1.
2.
3.
- 09 -
Airwheel reserves the right of nal interpretation of all the terms and conditions of this User Manual.
The driver should fasten safety belt after sitting on the seat.
Press the starting button and then the 5-scale charge volume display will be on or twinkles slowly,
Push the rocker slowly forward until you hear the sound of electromagnetic brake. At this time, the
H3S should move forward. Similarly, push or pull the rocker backward/leftward/rightward, the H3S
will move backward/leftward/rightward.
Adjust the speed scale button to regulate driving speed according to road condition, surrounding
conditions and personal preference.
When you want to stop, release the operational rocker and it will turn to central position. Then you
could hear electromagnetic sound soon, it means that the H3S is braking steadily.
Pay attention to surrounding conditions when moving backward. Slowly pull the rocker backward
and the H3S will move backward.
1.
2.
3.
4.
5.
6.
Lithium batteries can not be close to open re or high temperature heat source, can not be thrown into
water and can not be exposed in the sun in high temperature season.
Do not disassemble and decompose, as the internal part of them lithium battery has been packaged intactly.
The waste lithium battery of the product is to be recycled by the enterprise or dealer, and the
government designated outlets. Please do not throw away the waste battery, so as not to pollute the
environment.
4.
5.
6.
Charger usage:
Carefully check whether the charger's rated input voltage (AC100-240V) and the grid voltage is consistent.
When the vehicle needs charging,rst connect the battery to the charger, and then connect the charger to
AC power source .The charging indicator is red meaning it is charging. When it turns green, it will take 15
minutes to be fully charged. The charging time is about 2-4 hours (depending on the quantity of remaining
battery).
1.
2.
When charging, please put it in the safe place where children can not touch.
It is not advised to use it when it is not fully charged.
Do not use other brands of chargers, and other brands of batteries are not suitable for the use of the charger.
Do not disassemble, as the charger contains high voltage circuit.
Prevent liquid and metal particles from penetrating into the inside and be aware of falling and impact,
so as not to cause damage during use and storage.
When charging, do not afx any items.
Before long-period storage, make sure it powers off and is fully charged, and charge it every 2 or
3months.
Matters needing attention in charging:
How to Drive this H3S:
1.
2.
3.
4.
5.
6.
7.
- 10 -
When folding upward the armrest manually
(see step ①), please be careful and do
not overexert or exceed the limit.
When unfolding downward the armrest
manually, push the support rod downward
(see step ②) to make it easier to unfold.
Notes on folding armrest manually
①
②
- 11 -
Pull the tie rod to the open position, then the brake of H3S will not work, the weelchair can be
pushed by people(no matter the H3S is power on or power off, people can do it), when people pulf the
tie rod to the close position, nobody can push the H3S.
Tie rod of clutch
Hand mode Hand mode
Battery mode Electric mode
Tie rod of clutch
Hand mode, pull it
counterclockwise to
brake.
Electric mode, pull it
clockwise to brake.
Hand mode, pull it
clockwise to brake.
Electric mode, pull it
counterclockwise to
brake.
Operate tie rod of clutch
The clutch lever must be in electric mode, it means the H3S is braking, people can drive the
H3S.To ensure the security of people and H3S.it is prohibited to use this function when the
H3S uphill or downhill.
- 12 -
H3S
Exit folding state
System is normal
Exit folding state
System is normal
Exit folding state
System is normal
Exit folding state
System is normal
A
Airwheel Bluetooth password authenticatio
Intelligent helmet
Intelligent scooter
Search Devices
cancecomfirm
Input verify password 1111111
App download (optional)
Scan QR code to download
*Applicable to Android 4.3 or higher, iOS 7.0 or higher.
APP Instructions
1. Turn on H3S power button, and start App as well as Bluetooth.
2. Click the search button and do as the follows to connect
(verify password is 11111111).
3. Refer to ofcial website or give calls for details.
Click the Intelligent scooter
in the App interface.
Power on and enter the
home page.
Click the headlight button to
turn on the headlight. Click
the buzzer button, buzz
sound will be heard.
When the icon-H3S
showing on the home
page, it means it is ready
to be ridden.
When H3S is powered off, click the
contracting button and it will contract
automatically. Click the extending
button and it will automatically
extend. Click the stop button, it will
stop contracting or extending.
Click the search button
or .
Search Airwheel nearby,click
the searched Airwheel model
to connect.
Input the verify password:
11111111 to connect.
- 13 -
APP remote control operation (optional)
Backpack (optional)
km
Current mileage
System is normal
28
10.0
km/h
remote
control
km/h
forward
backward
left right
km/h
forward
backward
left right
Click the main interface
button to open the
sidebar.
Click the button in the
sidebar to open the remote
control interface.
The four corners’ Velcro are tied to the frame
respectively (see right Figure), to complete
the installation, and it can also be removed.
Move the button to operate
the intelligente scooter going
forward, backward or turning.
Slide the control speed
and click the icon to switch
to the hand-operationmode.
- 14 -
For indoor and outdoor usage
For indoor usage
The electronic equipment to be recovered separately (only for battery chargers)
Protection class-II
CE certication
Brake is activated
Brake is not activated (in the neutral position, it can be pushed or can not be ridden in
electric mode
Please be careful when going downhill in the neutral position
It’s not suitable to be the seat of motor vehicle
Product model
MP: +32 494 26 71 78
Airwheel Europe S.A.
Changzhou Airwheel Technology Co.,Ltd.
,
. .
P
TYPE
Other manuals for H3S
1
Table of contents
Other Airwheel Wheelchair manuals
