AL-KO AKS 2004 User manual

PLEASE ENSURE YOU READ THESE INSTRUCTIONS CARE-
FULLY, BEFORE COMMENCING TO OPERATE THIS PRODUCT.
GENERAL:
1) These notes are guidelines for use of the new handle only. They should
be read in conjunction with the “Assembly and Operating Instructions”
leaet, that should have been supplied with your stabiliser. Please refer to
this leaet for full guidance on maintenance/operation and coupling
procedures for AKS 2004 or AKS 3004. If you do not have a copy, please
request the following from our Service Department:
a) Operating Instructions for AKS 2004 - Part No. 1385399
b) Operating Instructions for AKS 3004 - Part No. 1387429
2) When not in use (during travelling or storage), the handle MUST be
removed from the stabiliser and stored within your vehicle. Providing the
stabiliser has been coupled correctly, the removal of the handle from the
stabiliser arms will not interfere with the normal operation of the stabiliser.
3) Suitable for AKS 2004/3004 Stabilisers only.
ASSEMBLY INSTRUCTIONS FOR
REPLACEMENT AKS 2004/3004 STABILISER HANDLE
PLEASE ENSURE YOU READ THESE INSTRUCTIONS CARE
FULLY, BEFORE COMMENCING TO OPERATE THIS PRODUCT.
GENERAL:
1) These notes are guidelines for use of the new handle only. They should
be read in conjunction with the “Assembly and Operating Instructions”
leaet, that should have been supplied with your stabiliser. Please refer to
this leaet for full guidance on maintenance/operation and coupling
procedures for AKS 2004 or AKS 3004. If you do not have a copy, please
request the following from our Service Department:
a) Operating Instructions for AKS 2004 - Part No. 1385399
b) Operating Instructions for AKS 3004 - Part No. 1387429
2) When not in use (during travelling or storage), the handle MUST be
removed from the stabiliser and stored within your vehicle. Providing the sta-
biliser has been coupled correctly, the removal of the handle from the stabiliser
arms will not interfere with the normal operation of the stabiliser.
3) Suitable for AKS 2004/3004 Stabilisers only.
ASSEMBLY INSTRUCTIONS FOR
REPLACEMENT AKS 2004/3004 STABILISER HANDLE

KIT CONTENTS (Fig. 1):
1) Replacement handle
2) Torx spanner
3) Fixing Screw
ASSEMBLY:
1) Removal of existing red handle from the stabiliser
lever arms:
a) using the torx spanner provided, undo and remove the
xing screw located on the side of the red handle (Fig.
2).
b) the red handle should now pull off the stabiliser lever
arms (Fig. 3).
2) Fitment of new handle
a) ensure both stabiliser lever arms are level
b) Push the new handle on to the lever arms (Fig. 4).
c) Insert xing screw and tighten using the torx spanner
(Fig. 5).
The handle is now ready for use.
Part No: 1552888 Rev 07/09
1)
3)
Fig. 3
AL-KO Kober Ltd
South Warwickshire Business Park, Kineton Road, Southam, Warwickshire, CV47 0AL
Phone: [phone] Fax: [phone] www.al-ko.co.uk
Fig. 1
2)
Fig. 2
Fig. 4
Fig. 4
Fig. 5
KIT CONTENTS (Fig. 1):
1) Replacement handle
2) Torx spanner
3) Fixing Screw
ASSEMBLY:
1) Removal of existing red handle from the stabiliser
lever arms:
a) using the torx spanner provided, undo and remove the
xing screw located on the side of the red handle (Fig.
2).
b) the red handle should now pull off the stabiliser lever
arms (Fig. 3).
2) Fitment of new handle
a) ensure both stabiliser lever arms are level
b) Push the new handle on to the lever arms (Fig. 4).
c) Insert xing screw and tighten using the torx spanner
(Fig. 5).
The handle is now ready for use.
Part No: 1552888 Rev 07/09
1)
3)
Fig. 3
AL-KO Kober Ltd
South Warwickshire Business Park, Kineton Road, Southam, Warwickshire, CV47 0AL
Phone: [phone] Fax: [phone] www.al-ko.co.uk
Fig. 1
2)
Fig. 2
Fig. 4
Fig. 4
Fig. 5