Alarm Lock 260 Manual

OPERATING INSTRUCTIONS
BEFORE INSTALLING THE LOCK COVER:
1) Select:
For continuous alarm, leave the black jumper plug on the terminal strip, as installed.
For two minute auto-alarm shutdown, remove the black jumper plug from the terminal strip.
2) Connect the battery connector to the 9-volt battery observing the proper polarity. A short beep will sound ensuring that the
lock is powered and ready.
3) Install the lock cover with four (4) screws supplied.
4) Close the door.
OPERATIONAL TESTING
1) Lock and unlock the door using the cylinder key and note a small beep will sound when the deadbolt is retracted, indicating a
disarmed condition. The door can now be opened without an alarm, by pushing the clapper plate.
2) Lock the door again and push the clapper plate to open it. Immediately the alarm will pulse loudly and one of the following will
occur:
A) If continuous alarm has previously been selected the alarm will sound until the lock is manually reset by locking the dead-
bolt with the key.
B) If auto-alarm shutdown has been selected, the alarm will sound for two minutes then reset.
LOW BATTERY DETECTION
When the battery becomes weak, the sounder will emit a short beep approximately once a minute indicating the battery needs
replacing.
RETRIGGERABLE OPERATION
If the unit has a retriggerable alarm (Model 260), after the initial two minute alarm and auto shutdown, the alarm will retrigger if
the door is opened again. This function will remain retriggerable until the door is relocked with the key. NOTE: Whenever an
alarm is caused by opening the door, and the door is left open, the two minute alarm shutdown will be inhibited.
WI1862 02/10
ALARM LOCK LIMITED WARRANTY
ALARM LOCK SYSTEMS, INC. warrants each of its products to be free from manufacturing defects in materials and work-
manship for fifteen months following the date of manufacture. ALARM LOCK will, within said period, at its option, repair or
replace any product failing to operate correctly, without charge to the original purchaser or user.
This warranty shall not apply to any equipment or any part thereof which has been repaired by others, improperly installed,
improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial
numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling, reassembly or reinstalla-
tion charges.
In order to exercise the warranty, the product must be returned by the user or purchaser, shipping costs prepaid, and insured
to ALARM LOCK. After repair or replacement, ALARM LOCK assumes the cost of returning products under warranty.
There are no warranties, express or implied which extend beyond the description on the face hereof. There is no express or
implied warranty of merchantability or a warranty of fitness for a particular purpose. Additionally, this warranty is in lieu of all
other obligations or liabilities on the part of ALARM LOCK.
This warranty contains the entire warranty. It is the sole warranty and any prior agreements, or, representations, whether
oral or written, are either merged herein or are expressly cancelled. ALARM LOCK neither assumes, nor authorizes any
other person purporting to act on its behalf to modify, to change, nor to assume for it, any other warranty or liability concern-
ing its products.
In no event shall ALARM LOCK be liable for an amount in excess of ALARM LOCK's original selling price of the product, for
any commercial loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of
the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or
liability shall arise or grow out of Seller's rendering of technical advice or service in connection with Buyer's order of the
goods furnished hereunder.
Warning: Despite, frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or
communications disruption, it is possible for the system to fail to perform as expected. Therefore, the consumer is advised to
take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling police or fire
department, in order to mitigate the possibilities of harm and/or damage.
This warranty shall be construed in accordance with the laws of the State of New Jersey.
INSTALLATION & OPERATING INSTRUCTIONS
WATERPROOF ELECTRONIC PANIC LOCKS
250 SERIES MODELS
ALARM LOCK SYSTEMS, INC.
345 BAYVIEW AVE., AMITYVILLE, NY 11701

DETAIL ASSEMBLY 250 SERIES
DIMENSIONS: Model 250 / 260: 18"W x 8½"H x 3¼"D
Model 250L / 260L: 24"W x 8½"H x 3¼"D
WEIGHT: 9 lbs. approx.
SHIPWEIGHT: 10 lbs. approx.
FINISH: US28 aluminum baked enamel
US3122 duranodic
POWER: 9VDC alkaline battery
CURRENT: Standby - 7 micro amps typical.
Alarm - 75 milli amps typical.
BATTERY LIFE:
One year standby typical.
200 alarm sequences typical.
or constant alarm for 7 hours typical.
LOW BATTERY DETECTION Short beep from piezo horn - 1 per minute typical.
AUTO ALARM SHUTDOWN: 2 minutes typical.
SOUND PRESSURE LEVEL: Dual piezo horn 95db measured at 10 feet
OPERATING TEMPERATURE: 20°F to 135°F (-7°C to 57°C)
NOTE: All above specifications rated at 72°F (22°C)
SPECIFICATIONS
DES. 'P' NO. DESCRIPTION
1 P0248 KEEPER COVER
2 P1140 (PART OF S5251 ASS'Y)
3 P1146 (PART OF S5252 ASS'Y)
4 P1151 (PART OF S3120 ASS'Y)
5 P1152 (PART OF S3120 ASS'Y)
6 P1157 KEEPER BASE
7 P1158 (PART OF S3113 ASS'Y)
8 P1159 (PART OF S3114 ASS'Y)
9 P1160 (PART OF S3114 ASS'Y)
10 P0250 KEEPER COVER*
11 P1168 (PART OF S5252 ASS'Y)
12 P1169 LATCH TRIP SPRING
13 P1170 D'LOCK LEVER SPRING
14 P1171 (PART OF S3121 ASS'Y)
15 P1250 CLAPPER PLATE (LONG)*
16 P1260 HINGE
17 P1508 6-32 X 1/4 L TRUSS HD.
18 P4545 CLAPPER ARM
19 P1520 (PART OF S5252 ASS'Y)
20 P1613 8-32 X 1/2 L PH PHIL.
21 P1615 8-32 X 1/2 L PH PHIL.
22 P1675 10 X 1 1/4 L PH PHIL.
23 P1676 10 X 1 1/2 L FH PHIL.
24 P1684 NUT 10-32 X 3/8 HEX.
25 P1739 10-24 X 1/2 L PH PHIL.
26 P1740 10-32 X 1/2 L FH PHIL.
27 P1748 10-32 X 3/4 L OVAL HD.
28 P1927 (PART OF S3113 ASS'Y)
29 P1928 (PART OF S3113 ASS'Y)
30 P1929 (PART OF S5251 ASS'Y)
31 P1930 (PART OF S5252 ASS'Y)
32 P1931 (PART OF S5252 ASSY)
DES. 'P' NO. DESCRIPTION
33 P1932 (PART OF S5252 ASS'Y)
34 P1933 (PART OF S5252 ASS'Y)
35 P1934 (PART OF S3120 ASS'Y)
36 P1935 (PART OF S3120 ASS'Y)
37 P1937 (PART OF S3121 ASS'Y)
38 P4155 10-24 X 5/8 PH PHIL.
39 P4493 CLAPPER ARM
40 P4495 TRIGGER CAM
41 P5232 PROD-LABEL 250/260
42 P5111 LOCK COVER (DURONODIC)*
43 P1143 (PART OF S3113 ASS'Y)
44 P1145 (PART OF S5252 ASS'Y)
45 P1149 (PART OF S5252 ASS'Y)
46 P1150 (PART OF S5252 ASS'Y)
47 P5012 PIEZO MT. PLATE
48 S5227 SUB-ASS'Y PCB
49 P5019 CAM FOLLOWER
50 P5029 TENSION SPRING
51 P5030 TENSION SPRING SPACER
52 P5031 LOCK COVER (ALUM)
53 P5050 CLAPPER PLATE
54 P5054 (PART OF S5252 ASS'Y)
55 S5228 SUB-ASS'Y PEZO SOUNDER
56 P5063 LOCK BASE PLATE
57 S5229 SUB-ASS'Y BATT.CONT.
58 P5077 BATTERY CLAMP BKT.
59 P5089 SPACER, NYLON 1/4 L
60 P5103 BATTERY, 9 VOLT
61 P5121 (PART OF S5252 ASS'Y)
62 P5195 SCRW. 2-56 X 1/2 L PH PHIL.
63 P5194 SCRW, 4-40 X 1/2 L PH PHIL.
64 P5197 SCRW, 10-24 X 3/4 L HEX SLOT
65 P5244 INTERNAL TOOTH LOCKWASHER
*Optional parts available. Contact your sales representative for more information.

STANDARD FEATURES
•WATERPROOF
•UNIT IS NON-HANDED
•DEADBOLT WITH HARDENED STEEL INSERT
•DEADLATCH FOR EASY ACCESS FROM INSIDE WITHOUT ALARM
•DEADBOLT CAN BE OPERATED BY OUTSIDE KEY
•LOCK ONLY REQUIRES 5 TO 10 LBS. OF FORCE TO OPERATE
•CAN BE USED FOR SINGLE OR DOUBLE DOORS
•LOUD DUAL PEZO HORN
•SELECTABLE - CONTINUOUS OR TWO MIN. ALARM SHUTDOWN
•DISARMING BEEP WHEN BOLT IS RETRACTED WITH KEY
•LOW BATTERY BEEP WHEN BATTERY NEEDS TO BE REPLACED
•RETRIGGERABLE ALARM AFTER TWO MIN. SHUTDOWN FOR MODEL
260 ONLY
INSTALLATION
SINGLE DOOR PAIRS OF DOORS PAIRS OF DOORS
WITH CENTER MULLIONS
Only one Exit Lock is required for each
exit door of this type
If two exit devices are not required, use one
lock with a Model 732 Double Door Keeper -
plus one Model 44 Double Door Holder on
the inactive door (or a vertical rod)
Pairs of this style should be treated as
two single exit doors. Use two Locks for
maximum safety and security.
ELECTRONIC PANIC LOCK ACCESSORIES:
FINISH BACK PLATE MODEL 767
Required to conceal the open back of the
lock body when mounted on a glass door.
Stainless Steel 4.5" x 8.5".
DOUBLE DOOR KEEPER MODEL 732
Applied to the surface of the inactive leaf of a
pair of doors. Plated Case Aluminum 7/8" x 6"
ARMORED DOOR LOOP MODEL 271
For use with Electrified locks.
An easy means for bringing electric current
from the hinge side of a door frame to the door.
18" flexible armored cable. End brackets are
deep drawn anodized aluminum to conceal
wire connections.
DOUBLE DOOR HOLDER MODEL 44
The Double Door Holder secures the inactive
door to the door frame while the active door is
closed. Releasing the active door automatically
allows both doors to swing freely. Reversible,
right or left hand doors. Cast aluminum 8.5"
long, 3" wide and 2.5" high.
THUMB TURN
MODEL THT
Used instead of cylinder
and keys to retract and
project the deadbolt
from inside.
CYLINDER
FINGER PULL
MODEL 711
An inexpensive door pull for use
when outside key only access is
required.
RIM CYLINDER
MODEL CER-OKC
Used to lock and unlock all
our exit and panic alarm locks
from outside. Includes two
keys for outside key control
(KA or KD).
OUTSIDE ACCESS
DOOR PULL MODEL 707
For access from build-
ing exteriors. Installed
on the outside of the
door and linked to the
lock. After deadbolt is
retracted by outside
key, a slight pull will
release the deadlatch
and open door. Cast
aluminum, 8" x 1.5".
SINGLE DOOR KEEPER
MODEL 730
Supplied for single doors or pairs of
doors with mullions.
LATCH HOLDBACK
DEVICE MODEL 747
An integral lock modifica-
tion which "dogs" the
latchbolt to provide a
hold-open function. Sim-
ply depress the latchbolt
beyond the face of the
lock and it will remain
retracted until the door is
relocked by key..
BATTERY ELIMINATOR MODEL AC-9
The AC-9 battery eliminator provides constant
regulated 9VDC power for Models 250 and
260. It is simple to install and maintenance
free. 117 VAC to 9VDC. The AC-9 conserves
the battery which automatically takes over as
the power source in the event of a power failure
or intentional power cutoff.
INSTALLATION & OPERATING INSTRUCTIONS
ELECTRONIC PANIC LOCK 250 SERIES
INSTALLATION
1) With the door closed, select the proper template and tape it to the inside face of the door with the
center line approximately 38" above the floor per template directions.
2) Mark and drill the following holes (see template for details):
A) FOR SINGLE AND DOUBLE DOORS: Mark six (6) .157" dia. holes, four (4) for the lock mount-
ing plate and two (2) for the keeper.
B) Mark a ¼" dia. hole for the rub plate on double doors 1¾" thick only.
C) IF OUTSIDE CYLINDER (CER-OKC) IS USED: Mark the center of the 1¼" dia. hole.
D) IF OUTSIDE PULL MODEL 707 IS USED: Mark the center of the four (4) ¼" dia. holes.
E) If mounting the lock on a hollow metal door and wires are to be run through the door, drill hole x
(see template). NOTE: If outside pull is used, drill four (4) holes ¼" dia. through the door from the
inside. Then drill ¾" dia. holes 1¼" deep from the outside of the door.
3) Remove the lock cover and four (4) screws holding the cylinder housing to the bolt cover. Install rim
cylinder (CER) with the keyway horizontal, facing the front of the lock (nine o'clock position) and cut
the cylinder tailpiece 3/8" beyond the base of the cylinder. Reinstall the cylinder housing, guiding the
tailpiece into the crosshole of the cam with four (4) screws.
4) Use the key to test for proper operation of the deadbolt. The key should be able to be withdrawn from
the lock in either the fully locked or fully unlocked position of the deadbolt. If not, the cylinder and the
cam are misaligned and the cylinder housing must be removed. Turn the cam a quarter (¼) turn to
the right, and reinstall the cylinder housing. (NOTE: The deadbolt can be projected into the keeper
by turning the key counter-clockwise and can be withdrawn from the keeper by turning the key clock-
wise one full turn.)
5) FOR OUTSIDE CYLINDER ONLY (CER-OKC): Install the rim cylinder with the keyway horizontal
facing the front of the door (three o'clock position) with the screws supplied and cut the tailpiece 3/8"
beyond the inside face of the door.
6) FOR OUTSIDE CYLINDER ONLY: Guide the tailpiece of the outside cylinder into the crosshole of
the outside cam.
7) Install the lock to the door with four (4) #10 screws as supplied.
8) FOR SINGLE DOOR ONLY: Remove the keeper cover, roller, and pin. Install the keeper base on the
door with two (2) screws supplied. Reinstall the pin, roller and cover with two screws.
FOR DOUBLE DOOR ONLY: Install the rub plate for a 1¾" wide door, from inside the door. Also in-
stall the 732 keeper with two (2) #10 screws supplied. Do not tighten the screws fully because the
keeper will require adjustment as mentioned in instruction 9.
9) FOR SINGLE DOOR ONLY: Close the door, project the deadbolt and adjust the keeper so that the
door is tightly latched. Retract the deadbolt, hold the keeper, release the latch and open the door
Open the keeper cover and tighten the screws. Drill a .157" dia. hole, as shown on template, for the
holding screw, and fasten the keeper with a #10 screw. Reinstall pin, roller and cover with two
screws.
FOR DOUBLE DOOR ONLY: Close the door, project the bolt and adjust the plastic slide on the 732
keeper so the door is tightly latched and tighten the screws.