Allen-Bradley 140G EXS3 Series User manual

Front spread terminal for 140G-G, 140G-H, 140G-I, 140G-J
Terminali anteriori divaricati
Vorderseitige verbreiterte Anschlüsse
Prises avant épanouies
Terminales frontales separadores
Bul. 140G/140MG
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
DIR 1000719R0805 Version 01 - 140G-_-EXS3, 140G-_-EXS4
140G-G 140G-I
140G-H 140G-J
CLACK
CLACK
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
1
1
140G-G
140G-H
140G-I
140G-J
4p
3p
x3
x2
x3
x2
x3
x2
x3
x2
x1
x1
x1
x1
x1
x1
/
/
x1
/
x1
/
x1
/
/
/
/
x1
/
x1
/
x1
/
/
x1
/
x1
/
x1
/
/
/
x1
x1
x1
x1
x1
x1
/
/
4p
3p
4p
3p
4p
3p x1
x1
/
x1
x1
x1
x1
x1
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/x1
x1
/
/
x1
x1
/
/
x2
x2
/
/
x2
x2
/
/
Terminals
Phase
barriers Insulator Screw
DIR 1000719R0805 Version 01
LENGTH dia.
6.5 mm (0.26") 2.9

(2)
2
34
56
1
OK
NO
OK
NO
140G-G 3p
4p
140G-H, 140G-I, 140G-J 3p
4p
3p
6 Nm
53 lb-in
140G-H 53 lb-in/6 Nm
140G-I, 140GJ 71 lb-in/8 Nm
140G-G, 140G-H 53 lb-in/6 Nm
140G-I, 140GJ 71 lb-in/8 Nm
1
3
1
3
2
4
1
32
2
4
OK
NO
7.87"/200 mm
4
DIR 1000719R0805 Version 01
1
2
2
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
G&I 140G-G-PB3H
H&J 140G-H-PB3H
G&I 140G-G-PB4H
H&J 140G-H-PB4H
7.87"/200 mm
2
1
2
2
1
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
1
1
1
1
CH 5
CH 5
CH 6
CH 5
CH 6

8
7
140G-H, 140G-J 3p
140G-H, 140G-J 3p
dia. 0.10"/ø 2.6 mm
XX
Y
Y
C
A
B
2
1
2
Ue > 440V
(3)
DIR 1000719R0805 Version 01
140G-H 140G-J
A3.24"/82.5 mm 3.05"/77.5 mm
B6.49"/165 mm 6.10"/155 mm
C11.1"/282 mm 12.83"/326 mm
LENGTH dia.
6.5 mm (0.26") 2.9

DIR 1000719R0805 Version 01 (L8101) - B0301
Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN091B-MU-P - September 2015
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
9140G-H, 140G-J 4p
1
2
2
Ue > 440V
140G-H 140G-J
A3.24"/82.5 mm 3.15"/80 mm
B7.68"/195 mm 7.68"/195 mm
C11.1"/282 mm 12.83"/326 mm
XX
Y
Y
C
A
B
dia. 0.10"/ø 2.6 mm
LE N GT H di a.
6. 5 mm (0.26" ) 2. 9